In-circuit Test Probe Pogo Pin PICT75 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PICT75� series here. Its� diameter is 1 mm� and the total length is 21 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly four types of receptacles, namely CR, SC, CRW� and SW� to fit each test probe.� For details, please check below parameters. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 150 milliohms Full Stroke: 4 mm Rated Stroke: 2.65 mm Spring Force:� 130 gf (4.5 oz) at load 2.65 mm Materials Contact Barrel: Phosphor Bronze, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
High-Current Probe Pogo Pin P203 for Electronic Test Cable harness test probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. Their standard and requirements are higher than other series of test probes. They can be divided into screw-thread harness test probes, cable harness switch probes, non-screw-thread harness test probes, position-limited harness test probes and cable harness high-current probes, etc. High-current probes can withstand high current and high temperature in the tests. They are mainly applied to the in-circuit test field of high temperature and high current environments. High-current probes manufactured by Centalic mainly include P203, P264, P265, P350 and P420, etc. There is a fixed schedule for mass production of P203. This probe can withstand the current up to 17 Amps. And its typical maximum contact resistance is 80 milliohms. The materials used for the construction of this high-current test probe are different for each component: The barrel is made of phosphor bronze. Subsequently gold and nickel plated during the galvanic plating phase. The spring is made of gold plated music wire. The plunger is made of beryllium copper, then gold and nickel plated. For details, please check parameters in below table. Technical Specifications Recommended Current Rating: 17 amps, continuous Contact Resistance: 80 milliohms, max Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 115 gf (4 oz) at load 4.3 mm Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Spring Loaded Pogo Pin Test Probe BIP68 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP68 series of battery contact probes. The outside diameter is usually 0.68 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 0.95 mm (37 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 0.5 mm Rated Stroke: 0.4 mm Spring Force: 10 gf (0.35 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Wire Harness Probe Pogo Pin CH203 Series for Electronic Test Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CH203 harness probe we will introduce here is 2.03 mm in diameter and 35.9 mm in total length. Its barrel is made of phosphor bronze plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of stainless steel plated with gold and nickel. This probe can withstand up to the current 5 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 5 mm at most when this probe works, although the plunger can move as far as 7.75 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 5 mm, its loaded force is about 145 gf, namely 5.5 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 5 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 7.75 mm Rated Stroke: 5 mm Spring Force: 145 ±43 gf (5.5 oz) at load 5 mm Materials (plated) Barrel: Phosphor Bronze, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SUS, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Cable Harness Contact Probe Pin CHL137 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHL137 harness probe we will introduce here is 1.37 mm in diameter and 26.7 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 100 milliohms. It is suggested the plunger be pressed at a distance of 2.8 mm at most when this probe works, although the plunger can move as far as 4.2 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 2.8 mm, its loaded force is about 100 gf, namely 3.5 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 100 milliohms Full Stroke: 4.2 mm Rated Stroke: 2.8 mm Spring Force: 100 ±30 gf (3.5 oz) at load 2.8 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Interface Probe Straight Brass Pin IFP-002 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-002, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-002 interface probe is 14.3 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
In-circuit Test Probe Pogo Pin PE75 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PE75 series here. Its test center is 75 mil. The diameter is 1.91 mm and the total length is 33.1 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly three types of receptacles, namely CR, SC and WW to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms Mounting Hole Size: Diameter 1.35 mm Full Stroke: 6.4 mm Rated Stroke: 4.3 mm Spring Force: 150 gf (5.5 oz)/200 gf (7.2 oz)/227 gf (8 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Nickel Plated or Gold Plated semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Test Probe BIP47 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP47 series of battery contact probes. The outside diameter is usually 1.6 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.54 mm (100 mil) Current Rating: 3 Amps, continuous Contact Resistance: 20 milliohms (Maximum) Full Stroke: 1.5 mm Rated Stroke: 1.5 mm Spring Force: 80 gf (2.8 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Wire Harness Probe Pogo Pin CHL165 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHL165 harness probe we will introduce here is 1.65 mm in diameter and 35.4 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 100 milliohms. It is suggested the plunger be pressed at a distance of 3.5 mm at most when this probe works, although the plunger can move as far as 5.3 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 3.5 mm, its loaded force is about 113 gf, namely 4 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 100 milliohms Full Stroke: 5.3 mm Rated Stroke: 3.5 mm Spring Force: 113�?�±35 gf (4 oz) at load 3.5 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Spring-Loaded Pogo Pin SCPA031(21) for Chip Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA031(21) we will introduce is 0.31 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2 Amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 0.7 mm. But it is better to be pressed at a distance of 0.45 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.45 mm, the loaded force is about 20 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 2 amps Contact Resistance: 100 milliohms max Bandwidth: 7.4 GHz at -1dB Inductance: 1MHZ at -0.05996 uH Captance: 1MHZ at 0.425647 uF Specifications: Full Stroke: 0.7 mm Rated Stroke: 0.45 mm Spring Force: 20�?�±6 gf at load 0.45 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Cable Harness Probe Pogo Pin CHL265 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHL265 harness probe we will introduce here is 2.65 mm in diameter and 28.4 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 100 milliohms. It is suggested the plunger be pressed at a distance of 3.5 mm at most when this probe works, although the plunger can move as far as 5.5 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 3.5 mm, its loaded force is about 113 gf, namely 4 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 100 milliohms Full Stroke: 5.5 mm Rated Stroke: 3.5 mm Spring Force: 113�?�±35 gf (4 oz) at load 3.5 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Interface Probe Straight Metal Pin IFP-003 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-003, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-003 interface probe is 16.33 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Interface Pin Test Probe IFP-005 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-005, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-005 interface probe is 17.8 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Semiconductor Test Probe Pogo Pin SCFE035 for Integrated Circuit Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCFE035 we will introduce is 0.35 mm in barrel diameter and 18 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold The bottom plunger is made from SK4 plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1.5 amps. The typical maximal contact resistance is about 150 milliohms. The plunger can be pressed at a distance of up to 1.5 mm. But it is better to be pressed at a distance of 1 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 1 mm, the loaded force is about 38 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: SK4, Au on Ni Plated Top Plunger: SK4, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 1.5 amps Contact Resistance: 150 milliohms max Bandwidth: 9.3 GHz at -1dB Inductance: 1MHZ at -0.05517 uH Captance: 1MHZ at 0.462432 uF Specifications: Full Stroke: 1.5 mm Rated Stroke: 1 mm Spring Force: 38�?�±11 gf at load 1 mm Mechanical Life: about 200000 cycles For more information, please check below catalog. Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Cable Harness Probe Pogo Pin CHZ199 Series for Electronic Test Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHZ199 harness probe we will introduce here is 1.99 mm in diameter and 33.2 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 4.4 mm at most when this probe works, although the plunger can move as far as 6.6 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 4.4 mm, its loaded force is about 133 gf, namely 4.7 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 6.6 mm Rated Stroke: 4.4 mm Spring Force: 133�?�±40 gf (4.7 oz) at load 4.4 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated For more information, please check below catalog. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Cable Harness Probe Pogo Pin CH136-J for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CH136 harness probe we will introduce here is 1.36 mm in diameter and 33 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 5.3 mm at most when this probe works, although the plunger can move as far as 8 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 5.3 mm, its loaded force is about 57 gf, namely 2 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 8 mm Rated Stroke: 5.3 mm Spring Force: 57±17 gf (2 oz) at load 5.3 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Pogo Pin SCPA030 Series for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA030 we will introduce is 0.3 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2 Amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1.1 mm. But it is better to be pressed at a distance of 0.65 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.65 mm, the loaded force is about 10 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph/ SP, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 2 amps Contact Resistance: 100 milliohms max Bandwidth: 7.1 GHz at -1dB Inductance: 1MHZ at -0.02524 uH Captance: 1MHZ at 1.12735 uF Specifications: Full Stroke: 1.1 mm Rated Stroke: 0.65 mm Spring Force: 10 ±3 gf at load 0.65 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Spring Pogo Pin Battery Contact Test Probe BIP94 for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP94 series of battery contact probes. The outside diameter is usually 0.94 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms (Maximum) Full Stroke: 0.78 mm Rated Stroke: 0.7 mm Spring Force: 30 gf (1.05 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu/SK4, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Battery Contact Probe Test Pogo Pin BIP148 Series for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP148 series of battery contact probes. The outside diameter is usually 1.49 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.16 mm (85 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 2 mm Rated Stroke: 1.33 mm Spring Force: 25 gf (1/ 0.9 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
In-circuit Test Probe Pogo Pin P085 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe P085 series here. Its diameter is 0.82 mm and the total length is 37 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Rated Stroke: 2 mm Spring Force: 130 gf (5oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated For more information, please check below catalog. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
