Type: vh660 Laser module: single glass lens Exterior sizes: ª¦130mm x 166mm Laser diode: horizontal 532nm vertical 532nm down point 650nm Accuracy: horizontal line: ía 1.0mm/5m Vertical line: ía 1.0mm/5m Line width: ín 1.8mm/5m Angle of projection: horizontal>100íp vertical>140íp Beam change: a. Horizontal b. Cross line C. Vertical d. Up point & down point Leveling range: ía 3íp Weight: about 1kg Power supply: 2 aa batteries Output power: < 5mw Operating temperature: 0-40 centidegree Operating time: single line: 8hours Central screw: 5/8" x11
Voltage:ac...220/230/250v, 50/60hz Ac...100/110/120v, 50/60hz Rated power:30w X/y scan angle:60 Scan rate:ilda 25k pps Working mode Dmx512, music active& automatic Pc laser show software:pangolin, phoenix, ishow and etc.(via lda port) Opotional mode I.Dew80 green(532nm)>80mw I.Dew60 green(532nm)>60mw I.Dew50 green(532nm)>50mw N.W:3kg size:270*150*80mm G.W:4kg(standrad carton package)
Voltage:ac...220/230/250v, 50/60hz Ac...100/110/120v, 50/60hz Rated power:100w X/y scan angle:60 Scan rate:ilda25kpps Laser diode Red(650nm)>150mw Green(532nm)>50mw Working mode Dmx512, music active &automatic Pc laser show software :pangolin, phoenix, ishow and etc(via ilda port) Additional function:pattern download via com1.Maximum 65535 images(2mb-8mbflash memory) Optional function:remote control Optional model I.Mist300 Red(650nm)>250mw Green(532nm)>50mw I.Mist400 Red(650nm)>300mw Green(532nm)>100mw N.W:4.5kg size:270*300*120mm G.W:5.5kg(standard carton package)
Voltage :ací¡220/230/250, 50/60hz Ací¡100/110/120v, 50/60hz Rated power :100w X/y scan a ngle:60 Scan rate:ilda30kpps Laser diode Green (532nm)>200mw Working mode Dmx512, music active& automatic Pc laser show software : pangolin, phoenix, ishow and etc(via ilda port) Additional function: pattern download via com1maximum 65535 image(2mb~8mb flash memory) Dmx512 mode Dmx512 channel :15chs Color :stochastic color, storbe , color corroding Gobo:255 gobos&30 group cartoon &30 group wave effect Movement :rotating , bounce, zoom, slow draw , stretch& rolling Optional function: remote control N.W:4.5kg size:270*300*120mm G.W: 5.5kg (standard carton package)
Voltage :ací¡220/230/250, 50/60hz Ací¡100/110/120v, 50/60hz Rated power :100w X/y scan a ngle:60 Scan rate:ilda25kpps Laser diode Red(650nm)>150mw Green(532nm)>50mw Working mode Dmx512, music active& automatic Pc laser show software : pangolin, phoenix, ishow and etc(via ilda port) Additional function: pattern download via com1maximum 65535 image(2mb~8mb flash memory) Optional function: remote contro N.W:4.5kg size:270*300*120mm G.W: 5.5kg (standard carton package)
Features: Small and light, conveniently to be carried Auto close light when scanner have trouble Safety capacity: design according to security and good performance, safer to human and environment Twinkling laser, more than 2,000 red and green beams shot out from the aperture within 70 angles, the effect of rotating direction, speed and frequently flashing controlled Applicable for disco, clubs, KTV, pub, bar, family party New product is the latest invention patent in the world with a unique effect and large marketing potential Specifications: Laser diode: diode pumped solid state laser (DPSS) Total laser power: 150mW Red laser: Wavelength: 650nm Laser power: 130mW Green laser: Wavelength: 532nm Laser power: 20mW Frequency: 50 - 60Hz Power supply: 12V DC Control: high capacity and speed microprocessor Scan system: micro-step motor scanner, big angle scanning Play mode: sound active, autoplay Inner packing size: 175 x 160 x 135mm Gross weight: 1kg . Paking:PE bag+stryrofoam+box packing size: 175 x 160 x 135mm Gross weight: 1kg .
1) Un-mounted Single-element Scan Lenses, STSL Series STSL scanner lenses specially designed and optimized for use in CO2 laser 2-axis galvo-scanner systems with full beam diameters of up to 15.0mm. 2) Mounted Single-element Scan Lenses, STDC Series. 3) Mounted 2-element Scan Lenses, STC Series The mounted 2-element scan lenses are 2-element designs for CO2 laser beams up to 15mm diameter, supplied complete in a mechanical housing.
Material: Nd:YAG Nd dopant concentration: as specified ¦ 0.1% Parallelism: 10" Flatness: l/10 @ 632nm Perpendicularity: < 2' Interference fringes: < 0.5 fringes/inch Extinction ratio: >15db Transmission with AR coating: ¦99.8% Damage threshold: >15J/cm2.
With a new development process, CNI has upgraded solid state 543 nm green laser up to 1 watt, 589 nm yellow laser up to 2 watts, and 660 nm red laser up to 2 watts, which has been designed as a complete laser solution for industry use in diverse applications.
1.Introduction The new generation of laser scribing machine YMS-50 (CE certificated product) is capable of scribing various silicon wafer, solar cell, ceramic wafer, thin metal sheet (~0.5 mm thick maximum), etc., in industries of electronics, semiconductor and solar energy, etc.. It is designed by experts with professional features, such as excellent beam quality and power stability, precise CNC worktable and efficient auto cooling system. Some of the most important parts are manufactured in UK, USA and Germany. Thanks to the automatic control of the whole system, you can save more efforts on the manufacturing, instead of how to operate and maintain the system. 2. Features Excellent beam quality and system reliability High-speed scribing (up to 120 mm/s), very low-defective index Auto cooling system Precise CNC worktable Friendly man-machine interface and simple software operation 3. Technical Parameters Laser medium Nd3+:YAG Wavelength 1064 nm Pump source Kr lamp Laser cavity Ceramic Modulated frequency 0.5 - 50 kHz Beam power Adjustable, max 50 W Aiming laser Red Scribing speed Adjustable, max 120 mm/ s Scribing depth Max 1.2mm Line width Min 0.2mm Worktable repeating accuracy 0.01mm Marking area 300 mm í- 300 mm Power supply 3-phase 4-wire AC 380V í+ 10%,50 Hz /60 Hz,PE,(A voltage stabilizer might be required to avoid irregular cutting quality caused by severe voltage fluctuation) Input power Max 5kW Dimension 550 mm x 290 mm x 650 mm Net weight ~560 kg Cooling Mode Water cooling 4.Standard Configuration Laser machine í- 1 set Exhauster í- 1 set Vacuum pump í- 1 set Cooling unit (Chiller, temperature controller, water tank, filter) í- 1 set Worktable unit (CNC controller) í- 1 set Kr lamp í- 2 pieces Laser detector í- 1 piece PC í- 1 set Scribing software (In English) í- 1 set Operation manual (In English) í- 1 Wooden Case
1.Introduction The laser scribing machine is specially designed for insulation of a-si (amorphous silicon) and back contacts such as aluminum coating of the a-si thin-film solar cell, without any damage to tco (transparent conductive oxidization) coating. 2. Features Cnc worktable size: 900mm íß 1600mm High-speed up to 500 mm/s or 200 íß 4 Auto programming / cooling / on-off Kerfs width 0.05 ¿c 0.15 mm, continuously adjustable 3. Technical parameters Wavelength 532 nm Laser output stability ín ía 3% Beam expanded angle ín 8 mrad Scribing speed Continuously adjustable, max 250mm/s Kerf width Continuously adjustable, 0.05 - 0.15 mm Scribing area 900 mm íß 1600 mm Power supply Single-phase ac 220v ía 10%, 50 hz /60 hz, pe, (a voltage stabilizer might be required to avoid irregular cutting quality caused by severe voltage fluctuation) Input power Max 1500w Cooling mode Air cooling 4.Standard configuration Laser machine íß 1 set Worktable unit (cnc controller) íß 1 set Pc íß 1 set Scribing software (in english) íß 1 set Operation manual (in english) íß 1. Wooden case
1.Introduction The laser scribing machine is specially designed for insulation of a-si (amorphous silicon) and back contacts such as aluminum coating of the a-si thin-film solar cell, without any damage to tco (transparent conductive oxidization) coating. 2. Features Laser: lamp-pumping laser Cnc worktable size: 500mm íß 500mm High-speed up to250 mm/s Auto programming / cooling / on-off Kerfs width 0.05-0.15 mm, continuously adjustable 3. Technical parameters Wavelength 532 nm Pump source Kr lamp Laser output stability ín ía 3% Beam expanded angle ín 8 mrad Scribing speed Continuously adjustable, max 250mm/s Kerf width Continuously adjustable, 0.05 ~ 0.15 mm Scribing area 500 mm íß 500 mm Power supply 3-phase 4-wire ac 380v ía 10%, 50 hz /60 hz, pe, (a voltage stabilizer might be required to avoid irregular cutting quality caused by severe voltage fluctuation) Input power Max 5kw Cooling mode Water cooling 4.Standard configuration Laser machine íß 1 set Exhauster íß 1 set Vacuum pump íß 1 set Cooling unit (chiller, temperature controller, water tank, filter) íß 1 set Worktable unit (cnc controller) íß 1 set Kr lamp íß 2 pieces Laser detector íß 1 piece Wooden case
1.Introduction The new generation of laser marking machine YMM-50 is applicable to almost any material surface. It offers various advantages with comparison to the traditional marking methods, such as noise-free, stress-free, ink-free, hazard-free (Printing marking uses hazardous solvent handling and disposal), tools-free and wearing-free(Tools wear in stamping systems). Laser marking technique offers a quiet, clean, low maintenance and easily configured system for permanent marking of almost any material surface. 2. Features Friendly and ergonomical man-machine interface Stable, precise and high-speed system File format to support any CorelDraw format, e.g., PLT, BMP, DST, etc.; Embedded test and graphic design tools offer various editing features Auto-numbering Barcode marking including Code 39, 93, 128, EAN-8, EAN-13, VIN, etc. and serial numbers Auto cooling Flexible text / graphics marking; Line or arc scribing to enable flexible profile scribing (Complicated profile scribing is optional) 3. Technical Parameters Wavelength 1064 nm Pump source Kr lamp Laser cavity Ceramic Laser output stability í_ í+ 3% Beam expanded angle í_ 8 mrad Aiming laser Red Linear speed Adjustable, max 5000 mm/ s Line width Min 0.1mm Letter size Min 0.5mm Marking area F=160 mm 70 mm í- 70 mm F=220 mm 100 mm í- 100 mm F=250 mm 150 mm í-150 mm Power supply Single-phase AC 220 V í+ 10%, 50 Hz /60 Hz,PE,(A voltage stabilizer might be required to avoid irregular cutting quality caused by severe voltage fluctuation) Input power Max 7kW Dimension 1500 mm x 500 mm x 1200 mm Net weight ~180 kg Cooling Mode Water cooling 4.Standard Configuration Laser machine í- 1 set PC í- 1 set Marking software (In English) í- 1 set Operation manual (In English) í- 1 Wooden Case
1.Introduction The laser marking machine YMM-10C is applicable to almost any non-metal surface. It has many clear advantages with comparison to traditional marking methods, such as noise-free, stress-free, ink-free, hazard-free (Printing marking uses hazardous solvent handling and disposal), tools-free and wearing-free (Tools wear in stamping systems). Laser marking offers a quiet, clean, low maintenance and easily configured system for permanent marking of almost any surface. 2. Features Unique optics design Friendly and ergonomical man-machine interface Stable, precise and high-speed File format to support any CorelDraw format, e.g., PLT, BMP, DST, etc.. Embedded test and graphic design tools offers various editing features Barcode marking including Code 39, 93, 128, EAN-8, EAN-13, VIN, Data Matrix, QR Code, etc. , and serial numbers 3. Technical Parameters Wavelength 1064 nm Aiming laser Red Linear speed Adjustable, max 5000 mm/ s Line width Min 0.2 mm Letter size Min 0.8 mm Marking area F=160 mm 70 mm í- 70 mm F=220 mm 100 mm í- 100 mm F=250 mm 150 mm í-150 mm Power supply Single-phase AC 220 V í+ 10%, 50 Hz / 60Hz Input power Max 210W Dimension 550 mm x 290 mm x 650 mm Net weight ~33.75 kg Cooling Mode Air cooling 4.Standard Configuration Laser machine í- 1 set PC í- 1 set Marking software (In English) í- 1 set Operation manual (In English) í- 1 Wooden Case
Sell tunable laser source of agilent 8164a, agilent 8168f, agilent 81689a, agilent 81640a, ando aq4320.
Laser power: 70w. Cutting size: 700mmx500mm. 1450x1000x1100mm.
Two cutting head Laser power:70x2w Cutting size:1200mmx600mm . 1820x1220x1150mm.
With cameral, Laser power:85w, Cutting size: 850mmx600mm . 2200x1160x1320mm(lxwxh).
Laser power: 70w Cutting size: 1000x800mm. 1580x1210x1110mm.
Products Characteristics 1.Advanced stepper control system with high precision and stalbe work function,support work on/off line. 2.Integrated design adopt the framework structure,stable and reliable,low noise. 3.Imported linear rail, advanced high-speed motor and driver, carving fast and higher precision. 4.High stability laser tube,imported lens and reflected mirror,infrared positon system ensure the cutting precision is high,incision is smooth. 5.Power off memory and breakpoint continuous carving function avoid wasting materials. 6.Laser Cut 5 software the latest support graphic format form the Auto CAD,Corel Drow,Photoshop and so on. 7.Multifarious work table such as honeycomb work table,aluminous strip work table and aluminous plate work table for choose, up-down device, rotary device optional. Technical Parameters We can supply different kinds of this machine:SF960,SF 1290,SF1410 and so on. 1.Model: SF 960 2.Work area:900X600mm 3.Laser power: 60W(option 80íó100íó130íó150W) 4.Laser type:Co2 sealed glass laser tube 5.Engraving speed:1-50000mm/min 6.Cuttting speed:1-30000mm/min 7.Minimum shapping character:Chinese character2x2mm,letter1x1mm 8.Maximal scanning precision:3000dpi 9.Location precision:
