industrial valves.
Valves, Electronic Valve, Pneumatic Valve, Solenoid Valve & Manual Valve.
Vane pump, piston pump, gear pump, hydraulic pump, valve, hydraulic valve.
Adblue sensor, fuel level sensor, adblue tank, mechanical gauge.
Variable vane pump manufacturers and suppliers Model : vdp-sf-12 Delivery at no load (l/min) : 1800rpm:12¡¢1500rpm:10 Pressure adjusting range (kgf/cm2) : 0 to 70 Shaft speed (rpm) : max:1800 ¡¢min:800 Pressure (kgf/cm2) : 70 Weight (kg) flange : 5 cooling circulating pump has build-in pressure setting, maintaining pressure at 3kg/cm2, protect pipe line of cooling system. rapid testes proven , to combine with proper cooler , it performed better cooling efficiency then cooling variable vane pump`s drain by air. aluminum alloy exterior of the cooling pump, with heat-absorbing strong , fast heat dissipation characteristics. by reduce size of reservoir , it could save space and volume of hydraulic oil.At the end , it saved cost. Mounting indusdruction 1.The rotation of vcm-sf pump is clockwise when viewed from the shaft end. 2.The drain pipe id directly connected to the oil tank and the positon must be below the level of oil. 3.Keep the suction pressure within 0.3 bar at the suction port. 4.Pressure adjusting scrow is turned clockwise to increase pressure and counterclockwise to increase flow and counterclockwise to decrease pressure. 5.Flow adjusting screw is turned clockwise to increase flow and counterclockwise to decrease flow. 6.For proper alignment of pump and electric motor shaft , the eccentricity between then must be kept within 0.05 mm and the eccentric angle error between them must be kept within 1¡ã. 7.When pressure is under 70 bar the viscosity os oil must be within 30-50 cst , when pressure is over 70 bar the viscosity of oil must be within 50-70 cst , at the temperature of 40¡ã. 8.When first time operation , the pump should be at no-load state-on delivery side and be repeated on and off the electric motor a number of times to make sure the air have been bled out of the system. Weight (kg) flange : 5 Packing:inside with a small box packaging, outside with a wooden box packaging
Variable vane pump manufacturers and suppliers Vdp-sf-12 Model : vdp-sf-12 Delivery at no load (l/min) : 1800rpm:12¡¢1500rpm:10 Pressure adjusting range (kgf/cm2) : 0 to 70 Shaft speed (rpm) : max:1800 ¡¢min:800 Pressure (kgf/cm2) : 70 Weight (kg) flange : 5 Packing:inside with a small box packaging, outside with a wooden box packaging Vane pumps; these hydraulic pumps have higher efficiencies than gear pumps, but are also used for mid pressures up to 180 bars in general. Unique shape and connection design , shorten the variable vane pump and cooling circulating pump length , small size , more compact shape. All alumium structure of the cooling pumps draw hydraulic oil tank , transported to the cooling system and returned to the tank , continuously loop, effectively lowering the oil temperature function. Weight (kg) flange : 5 Packing:inside with a small box packaging, outside with a wooden box packaging
product name: Valve body Material: aluminum Size: 9.2*9*4.2CM Weight: 232.3g Process: Die casting Surface treatment: no Use: Gas appliance aluminum profile assembly connectors accessories
V51 Firing pin valve is suitable for ultra micro dispensing precision striker valve. TE needle with inner diameter of 0.41 ~ 0.10mm can be used for high-precision ultra micro dispensing of various liquids. Feature: 1. Precision of ultra micro dispensing 2. Dispensing quantity adjust easily 3. Excellent function of clean in interrupt glue characteristic: 1. Ultra micro precision dispensing 2. Simple adjustment of dispensing amount 3. No bubbles in dispensing 4. Superior glue breaking function Parameters: Model V51 Cylinder body SUS303 Flow groove SUS303 Dimension 26.9 x 130mm Length Weight 320g Firing Pin seat SUS303 Liquid supply port 1/8NPT V-ring PTFE/SUS303 Driving pressure 0.4-0.62MPa Max fluid pressure 0.7MPa Mounting hole M6 Needle diameter 22G(ID (0.14)-33g( ID 0.1) Suitable for: low and high viscosity liquids, such as UV glue, solvent, lubricant, epoxy resin, etc.
V62 quick drying dispensing valve is an anaerobic single acting dispensing valve with one-way drive and thimble structure. It is suitable for the production of speakers and loudspeaker boxes, mechanical hole seam sealing, capacitor and module filling, dispensing of circuit board, canned beverage and liquid medicine, drip and coating with anaerobic adhesive, etc. Rapid and accurate action, maintain superior fluid glue breaking function, and simply control the precise flow of liquid. Feature: 1.Common barrier planning is selected to effectively isolate the fluid tank and rubber valve starting parts, so as to finely control the medium and low density fluid flow. 2.The echo time of the barrier valve can reach 15ms, and the glue breaking is clean and agile without dripping and leakage. 3.The fluid tank and diaphragm are made of polymer plastic materials. The polymer fluid tank can be used for various commonly used fluids such as solvent, instant drying glue, anaerobic glue and flux. 4.The black fluid tank can completely shield the light, making the UV dispensing operation safer. 5.The glue quantity is continuously adjustable, easy to clean and low protection. Parameters: Model V62 Flow groove Yellow UHMW Needle adapter Clear PP Cylinder body SUS 303 Stainless Dimension 26.9*79.0mm Weight 154g Diaphragm Yellow UHMW Mounting port M5 Driving pressure 0.4-0.62 MPa Max fluid pressure 0.48 MPa 1.Suitable for: low viscosity liquid,such as anaerobic adhesive,Quick-drying glue, solvent,adhesive,UV glue, epoxy resin,etc. 2.It can be connected with various needle nozzles, and can be connected with feed pump or storage pressure barrel. 3.Small size and light weight.
Pressure Pulsation Test Bench Pressure pulsation test bench is used to determine the ability of a pressure vessel to withstand pressure, and as a means of determining fatigue failure and simulating the design life of a component. Pressure pulsation test bench is common in various industries such as automotive, shipbuilding, heavy duty, and aerospace. In a typical test procedure and setup, the pressure vessel is connected to an outlet that injects a fluid (e.g., water or oil) into the component using appropriate fixtures. In short, the pressure booster generates a sinusoidal or trapezoidal curve of pressure on the filled test sample. In many cases, various variables are added through the tempering medium or a climatic chamber is added to simulate environmental conditions throughout the pressure pulsation test. Suncenter has rich experience in the hose, tube, pipe, valve pressure test field, we can provide reliable performance air(gas) and Pressure pulsation test bench, leakage test equipment, pressure pulse test equipment according to the standard of (GB/T5568, GB7939, ISO6802, ISO6803, ISO8032, GB/T12722, gb16897, GB/T5563, GB/T10544 etc.), do the test to the hydraulic hose and hydraulic hose assembly, automobile brake pipe, power train pipes and other pressure parts for pressure performance test. Applicable range of air/hydraulic pressure test equipment: Automobile steering tube, brake pipe, air-conditioning pipe, oil pipe, water pipe cooling, radiator, heater hose, hydraulic equipment, condenser, evaporator, air conditioning filter hose, turbocharging system hose, car brake pump, a cylinder body, a project hydraulic hose, air hose and manifold, rigid pipe, joints, valves, pressure gauges, pressure vessel, pressure transmitter etc.
Valve Test Equipment Valve test equipment can be used for a variety of applications, such as intermediate and final inspections by valve manufacturers, testing of new valves on delivery, and routine or post-maintenance testing of valves in service. These include, for example, pressure testing of valve housings, leakage testing of valve seats, and set pressure testing of safety valves. Other components can also be pressure tested, such as tanks, motor housings, pump housings, pipe fittings, insulators etc. Special clamping devices may be required to clamp these test pieces. Structure and working principle Valve test equipment is composed of hydraulic system, electrical control system, high and low pressure water pump pressure supply device system, oil pressure, water pressure instrument system, control valve system, clamping workbench system and hydraulic medium storage circulating water tank. The test process and results meet relevant regulations and requirements. The valve test equipment adopts flange end face sealing, holding pressure claw to directly clamp the valve, and the back of the flange is compressed. The clamping mechanism is directly driven by the clamping oil cylinder of the clamping claw. The axial direction of the clamping claw can move forward and backward, which is not limited by the thickness of the flange. The radial movement is composed of oil cylinder and lever to realize the radial synchronous movement of each clamping jaw. The radial clamping jaw can move forward and backward. It is not limited by the diameter of valve flange. There is no external force on the test valve. The left end of the test bench can move horizontally left and right, and the pressure test is not limited by the structural length of the test valve; The right end can be turned over 90 degrees to facilitate the sealing and air tightness test of the valve. The high-pressure water pump is powered by the 4-7 bar air pressure system and automatically reverses through the electrical control reversing valve to make the high-pressure water pump work automatically and reciprocally. The water suction check valve and water outlet check valve are interchanged to continuously supply pressure to the tested valve to meet the pressure requirements of the tested valve. It is applicable to the high-pressure water seal test of 1.1 times the nominal pressure, the high-pressure water shell test of 1.5 times the nominal pressure and the low-pressure air tightness test of 4-7bar for flange valves.
1- Hemostasis Valve (Y- click or luer ); 1- Torque Device; 1- Insertion Needle.
After-sales service: A: unconditional return or replacement within one month, the delivery fee shall be borne by the Dongguan yangling electronics Co.,LTD. B: Any purchase of any product within a week of quality problems can be replaced by the same products or other products. The delivery fee shall be borne by the Dongguan yangling e-commerce co., LTD. C: No quality goods to replace, return goods. Repair or replace the same goods within 1 week, and all delivery expenses shall be borne by the customer.
Solenoid Valve , Diaphragm Solenoid Valve, Direct Acting Solenoid Valve, High Temperature Solenoid Valve, High Pressure Solenoid Valve, Food Grade Solenoid Valve, Water Fountain Solenoid Valve, Anti Corrosive Solenoid Valve, Explosion Proof Solenoid Valve, Small Household Solenoid Valve, Auto Drain Solenoid Valve, Gas Solenoid Valve, Pulse Solenoid Valve, Motorized Valve, Pneumatic Valve, Manual Valve, Pneumatic Diaphragm Control Valve, Water Pressure Reducing Valve And Safety Relief Valve.
Mold components include mold counter, date inserts, gate inserts, hot runner system, air poppet valves, guide pin, guide bush.
Valve, nozzle, hot runner temperature controller, hot runner gate bush, hot runner valve pin.
Temperature sensor, pressure transducer, mechanical seals, air-intake valve, pressure maintain valve, unloading valve , loading valve, solenoid valve.
Measuring gauge,fastener,thread gauge,Valve.
Vacuum pump, air filter, pressure relief valve, silencer..
Automatic dispensing machine, diy three axis mechanical arm, automatic visual positioning dispensing machine, hot melt dispensing machine, automatic calibration needle dispensing machine, gantry dispensing machine, floor dispensing machine, four axis universal platform, automatic soldering machine, automatic screw machine, online visual dispensing system, glue quantity controller, high speed jet valve, precision screw valve, various precision dispensing valves, precision screw pumps, etc..
