Ature:remove all oil or grease, soluble contaminants and other foreign matter All surfaces to be coated should be clean, dry and free from contamination If applied on rusty surface, rusty layer thickness should be below 50mm, other than bottom surface processing requirements, without acid and sandblasting processing, catalytic reaction, to get black protective layer and solvent (acrylic acid, polyurethane, epoxy resin, alkyd resin, amino paint or water-based paint) match well, will not occur and paint color bleeding Apply in nice weather, don't let coating contact any liquid like water or other solvent before completely dry No painting be carried out in rainy day outdoor If above 85% humidity please stop painting Temperature of substrate should be above 5¡ãc Lower temperature might not dry or cause long time to dry •air spray:nozzle orifice range: 1.5 to 2.5mm Nozzle pressure range: 0.3 to 0.5mpa •airless spray:nozzle orifice range: 0.4 to 0.5mm Nozzle pressure range: 12 to 15mpa •features:brush: use soft brush Recommended finish: rsl series Storage temperature: 5 to 30¡ãc in well ventilated warehouse Stir thoroughly before painting Don't use any steel or other metal stick to stir paint 20l/barrel
Can be applied directly on rusty steel( rust layer ¡ü45um)! Color and appearance: grey or others Coating thickness um: 50¡à5mm Solid content % : 69¡à3% Overcoating interval: minimum: 4 hours max: unlimited Recommended substrate conditions and temperature: 1.Remove all oil or grease, soluble contaminants and other foreign matter. All surfaces to be coated should be clean, dry and free from contamination. 2.If applied on the rusty surface, the rusty layer thickness should be below 45 um 3.Apply in good weather, don¡¯t let coating contact any liquid like water or other solvent before completely dry. No painting be carried out in rainy day outdoor , if the humidity is above 85%, please stop painting 4.The temperature of substrate should be above 5¡ãc, lower temperature might not dry or cause a long time to dry Air spray:nozzle orifice: 1.5-2.5mm Nozzle pressure: 0.3-0.5mpa Airless spray:nozzle orifice: 0.4-0.5mm Nozzle pressure: 12-15mpa Brush : use soft bursh Recommended finish: rsl series finish Shelf life: 12 months Over coating time Substrate Temperature 5¡ãc 15¡ãc 25¡ãc 35¡ãc 45¡ãc Minimum interval 24hrs 7hours 4hours 3hours 2hours Maximum interval Unlimited storage temperature : 5-30¡ãc in well ventilated warehouse 20l/barrel or 20kg/barrel
Hjsil 150 Characteristics Hjsil150 is a hydrophilic fumed silica with a specific surface area of 150 ©o/g. It is a kind of high purity white colloidal powder. Applications Htv and rtv silicone rubber Adhesives and sealants Paints and coatings Properties Reinforcement filler in elastomers Rheology and thixotropy control of liquid systems, binders, polymers, etc. Used as anti-settling, thickening, anti-sagging agent Improvement of free flow and anti-caking characteristics of powders 3-layer kraft paper bag, 10kg per bag.
Reinforcement filler in elastomers Rheology and thixotropy control of liquid systems, binders, polymers, etc. Used as anti-settling, thickening, anti-sagging agent Improvement of free flow and anti-caking characteristics of powders High transparency 3-layer kraft paper paper bag, 10kg per bag
Disposable painting-overall with hood -size s, m, l, xl, xxl -extremely comfortable with elastic sleeves and trouser legs -abrasion resistant, hard wearing, antistatic, breathable fabric. -material is polyester -zipper on the front, hidden Carton
The equipment adopts the resistance heating in the vacuum chamber, to melt and vaporize the metal wire (aluminum wire) cling to the resistance wire. The vaporized metal molecule deposit on the substrates, to gain the smooth film as well as high reflectivity. Thus the surface of the items can be decorated and beautified. Characteristic: reasonable structure, even film, good-quality film forming, quick pumping speed, the cycle of short, high efficiency and easy operation, low energy consumption and performance advantages of stability. Applied industry: Widely used in automotive, audio and various small appliances, computers, clocks and watches, toys, cell phones, reflective Cup, cosmetics, toys, tableware, sanitary ware, shoe heel, ABS, PS, PP, PC, PVC, PET, nylon, metal, Boli, glass, ceramics, TPU, etc. Electroplating effects: general electroplating-face, dumb-(semi-mute, all dumb), the electroplating process wrinkles, lampworking, raindrops, seven colors Coating color:gold, silver, red, blue, green, purple, multi color, and so on. Coating color: gold, silver, red, blue, green, purple, and so on. All vacuum coating machines are environmental prodection products and sooner or later will replace traditional galvanization industrial. Technical parameter: Mode Dimension ZZ-1200 ZZ-1400 ZZ-1600 ZZ-1800 1200*1400mm 1400*1600mm 1600*1800mm 1800*2000mm Mainly Application Plastic decorative coating , glass decorative coating and protective film coating Film Type Semitransparent film, non-conducting film, gold, silver, red, blue, green, purple, seven color, etc. Power source Type Thermal evaporation power, ion bombard power, RF power Vacuum chamber structure Vertical double/single door, horizontal single door, pump system postposition Ultimate vacuum 8.0*10-3Pa Vacuum system Diffusion pump +Roots pump +Mechanical pump +Holding pump Pump time Pump from atmosphere to 5.0*10-2, 6 minutes Workpiece motion mode Public rotation/Frequency control Control mode Manual/Automatic all-in-one mode, Touching screen+PLC compress air the pressure is 5~6kg. water-cooling system Cool water 5~25 supplier, the flux is 5T/H and the pressure is 0.15~0.25MPa. Features Bright delicate aluminum coating, coating speed, simple operation, equipment stability, and the production of high-grade plastic decoration products indispensable a necessary equipmen flat container
Ceramic gold coating machine can coat tin, tic, zrn, crn, ti, ni, cr, cu and other compounds film, multi-layer super-hard film, nitrogen-doped titanium film and the alloy film, and in a very short time to complete all the machining process, it is a highly efficient multi-functional coating equipment. Technical parameter: Mode Dimension Lh-800 Lh-1100 Lh-1250 Lh-1600 Lh-1800 800*1000mm 1100*1000mm 1250*1500mm 1600*1800mm 1800*1800mm Maily application Metal decorative coating and ceramic decorative coating Coating mode and main confirguration Eight multi-arc targets Ten multi-arc targets Twelve multi-arc targets Twenty multi-arc targets Twenty two multi-arc targets Power source Electric-arc power, filament power, Process gas control Mass flowmeter + electromagnetic ceramic valve Vacuum chamber structure Vertical side opening door, pump system postposition, double water cooling Vacuum system Molecule pump +roots pump +mechanical pump(8.0*10-5pa) Diffusion pump +roots pump +mechanical pump(8.0*10-4pa) Workpiece baking temperature Normal temperature to 350 centi-degree pid control, radiation heating. Workpiece motion mode Public rotation frequency control: 0-20 rotation per minute Measure mode Number display composite vacuum gauge: from atmosphere to 1.0*10-5pa Control mode Manual/automatic/pc/plc + hmi/pc four choice of control mode Remark We can design the dimension of the equipment according to customers special technique requirement. 40gp container per set
Property: 1. Excellent chemical resistance 2. Excellent electric insulativity 3. Excellent adhesive force 4. High degree of hardness - good mechanical property Application used for : 1. Coating metal cabinets, 2. Electric distribution boards, 3. Lighting components, 4. Metal shelves, 5. Air conditioners, 6. Office furniture. Solidifying condition: 20min/180-190 degrees. Trademark: rengui Packing: 20kgs/carton or 25kgs/carton Origin: china Production capacity: 600 tons/month 25kgs/carton, sealed plastic bags with brown carton
Property: 1. Excellent chemical resistance 2. Excellent electric insulativity 3. Excellent adhesive force 4. High degree of hardness - good mechanical property Application used for : 1. Coating metal cabinets, 2. Electric distribution boards, 3. Lighting components, 4. Metal shelves, 5. Air conditioners, 6. Office furniture. Solidifying condition: 20min/180-190 degrees. Trademark: rengui Packing: 20kgs/carton or 25kgs/carton Origin: china Production capacity: 600 tons/month 25kgs/carton
Property: 1. Excellent chemical resistance 2. Excellent electric insulativity 3. Excellent adhesive force 4. High degree of hardness - good mechanical property Application used for : 1. Coating metal cabinets, 2. Electric distribution boards, 3. Lighting components, 4. Metal shelves, 5. Air conditioners, 6. Office furniture. Solidifying condition: 20min/180-190 degrees. Trademark: rengui Packing: 20kgs/carton or 25kgs/carton Origin: china Production capacity: 600 tons/month 25kgs/carton
Plative PLP4500 plating layer protective paint Brief description Plative PLP4500 plating layer protective paint, is designed to protect the plating layer by improving abrasion resistance, scratch resistance, chemical corrosion resistance, insolation and heat stability. The paint of transparent has no effect on the color of plating layer, besides the paints of colorful can make the plating layer with different coloration. Operational guidance Prefabricated, diluted plative PLP4500 to a proper consistency and add 15% -25% to total plative SN30, mix completely. Clean and dry the plating layer, make sure no oil, no dust. To paint the layer with prepared paint by spraying, immersion or drawing. Then forced dry at 120 ¡æ in 50 minutes, or air dry in more than 12 hours. Annotation Before use, low-speed mixing of plative PLP4500 is required; dilute the product with special solution alative PLP4500, or else it could lead to paint deterioration. Plative PLP4500 plating layer protective paint brief description Plative PLP4500 plating layer protective paint, is designed to protect the plating layer by improving abrasion resistance, scratch resistance, chemical corrosion resistance, insolation and heat stability. The paint of transparent has no effect on the color of plating layer, besides the paints of colorful can make the plating layer with different coloration. operational guidance Prefabricated, diluted plative PLP4500 to a proper consistency and add 15% -25%to totalplative sn30, mix completely. Clean and dry the plating layer, make sure no oil, no dust. To paint the layer with prepared paint by spraying, immersion or drawing. Then forced dry at 120 in 50 minutes, or air dry in more than 12 hours. Annotation Before use, low-speed mixing of plative plp4500 is required; dilute the product with special solution alative PLP4500, or else it could lead to paint deterioration.
Plative DPP3800 deplate protective paint Brief description Plative DPP3800 deplate protective paint, the paint is prepared from a special process with special resins, special solution and other materials. Specific features are no affect on plating coat, acid and alkali resistance, against corrosion, and so on. Commonly used in deplating process where can protect the plating coat from damage. The plating coat such as aluminum, nickel, copper, tin, chrome and so on. Operational guidance First, to clean and dry the plating layer, make sure no grease, no dust. Second, to paint the surface where prevent from being processed next (alative DPP3800 can be used to dilute the product). Then forced dry at 70 before deplating. After deplating, the coating can be cleaned or not, with special cleanser. Annotation Before use, low-speed mixing of plative dpp3800 is required; dilute the product with special solution alative dpp3800, or else it could lead to paint deterioration.
Plative PPC7703 peelable protective paint Brief description Plative PPC7703, the peelable protective paint, is specialized applied to protect the based design of workpiece form destruction of post-processing. Acid or alkali resistance, corrosion resistance, good adhesion, and fast-drying, peeling easy. Operational guidance First, to clean and dry the surface, make sure no grease, no dust. Second, to paint the surface where prevent from being processed next (alative T7703 can be used to dilute the product). Then, forced dry at 70 before post-processing. After processing, the coating can be manual stripping, or peeled with adhesive tape. Annotation Before use, low-speed mixing of plative PPC7703 is required; dilute the product with special additives alative T7703, or else it could lead to paint deterioration; the film with a certain thickness, is in order to peeling easy after printing. Plative PPC7703 peelable protective paint Brief description Plative PPC7703, the peelable protective paint, is specialized applied to protect the based design of workpiece form destruction of post-processing. Acid or alkali resistance, corrosion resistance, good adhesion, and fast-drying, peeling easy. Operational guidance First, to clean and dry the surface, make sure no grease, no dust. Second, to paint the surface where prevent from being processed next (alative T7703 can be used to dilute the product). Then, forced dry at 70 before post-processing. After processing, the coating can be manual stripping, or peeled with adhesive tape. Annotation Before use, low-speed mixing of plative PPC7703 is required; dilute the product with special additives alative T7703, or else it could lead to paint deterioration; the film with a certain thickness, is in order to peeling easy after printing.
Plative ISP3320 anodizing protective paint Brief description Plative ISP3320, a kind of antioxidant protective paint, is specialized applied to anodizing treatment. Strong acid resistance such as hydrofluoric acid, concentrated sulfuric acid. Good adhesion. Good leveling Operational guidance First, to clean and dry the surface, no oil slicks, no dust. Second, to paint the surface where prevent from plating or pickling next (the corresponding additives can be used to dilute the product) painting by screen printing, pad printing, scratch, dipping, or spraying. Then 160-200heat cured in 20-30 minutes. To clean the coating with the corresponding removers after anodizing. Annotation Considering the painting method, please dilute the product to appropriate viscosity before use please use the corresponding thinners, or else it could lead to paint deterioration; during operation, please keep the environment ventilation to prevent inhalation. Plative ISP3320 anodizing protective paint brief description Plative ISP3320, a kind of antioxidant protective paint, is specialized applied to anodizing treatment. Strong acid resistance such as hydrofluoric acid, concentrated sulfuric acid Good adhesion. Good leveling operational guidance First, to clean and dry the surface, no oil slicks, no dust. Second, to paint the surface where prevent from plating or pickling next (the corresponding additives can be used to dilute the product)painting by screen printing, pad printing, scratch, dipping, or spraying. Then 160-200heat cured in 20-30 minutes. To clean the coating with the corresponding removers after anodizing. annotation Considering the painting method, please dilute the product to appropriate viscosity before use; please use the corresponding thinners, or else it could lead to paint deterioration; during operation, please keep the environment ventilation to prevent inhalation.
1. Simple to apply and to repair 2. Long term good looks and low maintenance 3 .Ready to use,just add water 4. DIY eco-friendly paint. Inner plastic package,1kg/bag.
Name: water-based varnish (self-adhesive) Model: H-5803C Use: for in-line printing , wet to wet printing , self-adhesive , for noodles package . Description: H-5803C is a plus by a special acrylic polymer emulsion with functional additives varnish, It has strong adhesion for the paper after it was hot of the Ultrasonic heating. This varnish has excellent gloss, good gloss and color retention, dry fast, good printability. The wet-wet and wet-dry printing has good wetting leveling, strong anti-alcohol ,printing machine is easy to clean. Dedicated to the noodles package(such as Master), which need ultrasonic to glue Automatic .This varnish is used off-line coating, can also be used for inline coating. Appearance: milky white liquid, Solid content 40%, Viscosity (seconds): 18 ~ 20, (3 cup, 25 ), Gloss: 55 5 Notes: 1, It based on conditions of use plus appropriate diluent (water) or alcohol and water (1-5:1) mixture dilution. In order to achieve gloss and abrasion resistance requirements of the situation according to the paper, roll coated with light plus 5 to about 15% thinner, with inline coating liquid, the use of high viscosity coating process should be adjusted to increase the amount of diluent the appropriate viscosity. 2, Varnish on paper should meet the principle, if excessive dilution will affect gloss, abrasion resistance and leveling; the contrary will result in dilution of inadequate leveling varnish is not good, the drying rate is too slow . 3, depending on fuel quality and gloss paper requirements, are generally on-line coating of :2-5 g / m, offline coating 3-7g / m. 4, drying method: to use infrared drying, hot air or heat pipe heating and drying. Drying equipment operation during the first table shows the temperature not lower than 70 . 5, Take 12 hours after polishing of the varnish in order to achieve optimal performance. 6,It can use water to clean equipment, the dry varnish can used Isopropyl alcohol or alcohol to clean. 7, the product of alkali-soluble varnish, when veneer to the cartons (laminating), try to choose a neutral or weakly alkaline (PH 10) adhesives, when used starch caustic soda glue (yellow glue) fluid, Please be strictly controlled to avoid excess glue with a glue penetrate varnished surface caused by dissolution of the coating adhesive. Package: 25KG/50KG/120KG plastic containers, sealed in a cool place, the shelf life is one year.
Name: water-based varnish (in-line) Model: H-5303C Use :for in-line printing , wet to wet printing , matt ,for paper package . Description: H-5303C is an environmentally friendly oil dumb fast printing, excellent wear resistance, good leveling characteristics. Fast drying and good printability. Wet ink on good wetting leveling, strong resistance to alcohol, printing machine is easy to clean. Used for frozen packaging, bottled instant noodles, electrical appliances, wine packaging and other high-end printing cigarette packaging. This varnish coating for offset printing blanket, inline coating, glazing, and off-line flexo coating. Appearance: milky white liquid, Solid content 40%, Viscosity (seconds): 18 ~ 20, (Viscosity Cups 3 , 25¡æ) Gloss: 6 ~10 Notes: 1, It based on conditions of use plus appropriate diluent (water) or alcohol and water (1-5:1) mixture dilution. In order to achieve gloss and abrasion resistance requirements of the situation according to the paper, roll coated with light plus 5 to about 15% thinner, with inline coating liquid, the use of high viscosity coating process should be adjusted to increase the amount of diluent the appropriate viscosity. 2, Varnish on paper should meet the principle, if excessive dilution will affect gloss, abrasion resistance and leveling; the contrary will result in dilution of inadequate leveling varnish is not good, the drying rate is too slow . 3, depending on fuel quality and gloss paper requirements, are generally on-line coating of :2-5 g / m, offline coating 3-7g / m. 4, drying method: to use infrared drying, hot air or heat pipe heating and drying. Drying equipment operation during the first table shows the temperature not lower than 70. 5, Take 12 hours after polishing of the varnish in order to achieve optimal performance. 6,It can use water to clean equipment, the dry varnish can used Isopropyl alcohol or alcohol to clean. 7, the product of alkali-soluble varnish, when veneer to the cartons (laminating), try to choose a neutral or weakly alkaline (PH 10) adhesives, when used starch caustic soda glue (yellow glue) fluid, Please be strictly controlled to avoid excess glue with a glue penetrate varnished surface caused by dissolution of the coating adhesive. 25kg/50kg/120kg plastic containers.
Name: Water-based Varnish (high viscosity) Model: H-5312 Use : high gloss ,high viscosity ,for paper package printing Description: H-5312 is an environmentally friendly water-based varnish, excellent wear resistance, high gloss, gloss retention, dry fast, good printability. A variety of ink has good wetting leveling, printing machine is easy to clean s. It is meet the national and EU environmental standards, through the EU ROHS test, compliance with international environmental requirements. Scratch resistance is strong, mainly used for dusting and more printing, high wear resistance. Appearance: milky white liquid, Solid content: 461%, Viscosity (Viscosity Cups 3 , 25 seconds): 18 ~ 20, Gloss: 4 ~ 7 Notes: 1, It based on conditions of use plus appropriate diluent (water) or alcohol and water (1-5:1) mixture dilution. In order to achieve gloss and abrasion resistance requirements of the situation according to the paper, roll coated with light plus 5 to about 15% thinner, with inline coating liquid, the use of high viscosity coating process should be adjusted to increase the amount of diluent the appropriate viscosity. 2, Varnish on paper should meet the principle, if excessive dilution will affect gloss, abrasion resistance and leveling; the contrary will result in dilution of inadequate leveling varnish is not good, the drying rate is too slow . 3, depending on fuel quality and gloss paper requirements, are generally on-line coating of :2-5 g / m, offline coating 3-7g / m. 4, drying method: to use infrared drying, hot air or heat pipe heating and drying. Drying equipment operation during the first table shows the temperature not lower than 70 . 5, Take 12 hours after polishing of the varnish in order to achieve optimal performance. 6,It can use water to clean equipment, the dry varnish can used Isopropyl alcohol or alcohol to clean. 7, the product of alkali-soluble varnish, when veneer to the cartons (laminating), try to choose a neutral or weakly alkaline (PH 10) adhesives, when used starch caustic soda glue (yellow glue) fluid, Please be strictly controlled to avoid excess glue with a glue penetrate varnished surface caused by dissolution of the coating adhesive. Package: 25KG/50KG/120KG plastic containers, sealed in a cool place, the shelf life is one year.
Scope of application: 1. Electron, appliance, ironware, machine factory 2. Chemical, medicine factory, lab 3. Food, textile, supermarket, parking lot. Features: Dust-proof, waterproof, mold-proof, chemical resistant, wear-resistant, strong adhesion, smooth and seamless, simple construction, easy to clear and maintain. Construction technology: 1. Waterproof treatment: first floor needs well done waterproof; 2. Basic ground treatment: polish, fix and clean according the basic ground condition; 3. Epoxy primer: use strong Permeability and adhesion epoxy primer roll-coating one time, strengthen surface adhesion; 4. Epoxy putty: construction several times according practical demand, up to smooth without holes, mark of Batch cutter and sand polish; 5. Epoxy topcoat: use epoxy topcoat or slip-resistant topcoat roll-painting two times, when finished the floor is smooth and clean, color average and no hollowing. 25kg/drum.
Jelee water based glass baking enamel is made with modified acrylic resin as raw material. 25kgs in plastic drums.