Wedge wire filter, johnson screen, johnson well screen, intake screen, wedge wire basket, sieve bend screen, rotary drum screen.
Roll width: 24inch, 36inch, 1meter, 48inch or 72inch Roll length: 100feet or 150feet Mesh size: 6.4-50.8mm Wire gauge diameter: 0.56-2.77mm It is up to customer's request.
our product and engineering know-how is used in a wide array of mission-critical applications around the world, including ultra-fine filtering, separating and sizing of particles; lightning strike protection on commercial aircraft; acoustic modulation and suppression of high-frequency sound on aircraft and in consumer products; EFI/RFI shielding of military aircraft; rechargeable batteries and fuel cells; heat dissipation in cryogenic environments; oil and gas exploration and well development; and numerous automotive applications.
Welded mesh fabric Welded mesh fabric used for the reinforcement of concrete is manufactured to international standard specifications. Features: 1welded mesh reinforcing sheets are the most commonly used form of reinforcing in concrete and is particularly suited for flat slab construction and concrete surface beds. Other design applications would be: Retaining walls Shear walls Beams and columns. Concrete paving overlays Suspended floor slabs Swimming pool and sp rayed concrete reinforcing 2welded mesh sheets can be detailed as either flat or bend sheets depending on the contract requirements. 3welded mesh sheets can be fabricated to non-standard sizes depending on contract requirements. 4welded mesh reinforcement reduces construction time considerably by eliminating the tying of reinforcing bars on site. 5designated fabric mats are standard welded reinforcing sheets and can be scheduled simply by reference to the fabric type, sheet dimensions and in instances where bend material is required the bending shape code. (the reference is the nominal mass of the fabric in kg/m x 100) 6the cold-rolled deformed wire used in welded mesh reinforcement fabric has a minimum characteristic strength (0.2% proof stress) of 485 mpa compared to 450 mpa for high tensile rebar. Reinforcing fabric may be used at higher stresses than high tensile rebar resulting in material saving of up to
Anping Tenglu Metal Wire Mesh Co.,LTD Inconel Wire Mesh Product Description: Inconel Mesh has excellent resistance to carburization, pitting and crevice corrosion, stress corrosion cracking and oxidation. It is resistant to a wide range of corrosive media such as organic, inorganic compounds, acids and alkali. It possesses high temperature mechanical strength, creeping resistance and long service life. Inconel 600 Mesh: Alloy 600 has outstanding resistance to heat, oxidizing and corrosive media and offers performance temperature up to 2000oF. It is resistant to SCC and reducing media and has good mechanical characteristics from cryogenic to high temperatures. Inconel 601 Mesh: Inconel 601 has great oxidation resistance up to 1250oC or 2200oF. It is called as a high temperature mesh material offering good spalling resistance, creeping strength and high temperature stability. It maintains ductility even after prolong service. Inconel 617 Mesh: Alloy 617 offers elevated temperature oxidation and corrosion resistance up to 1800of. It offers high mechanical strength and great metallurgical stability. The alloy is resist to pitting and crevice corrosion and variety of strong acids such as hydrochloric acid, hydrofluoric acid, sulfuric acid and nitric acid. Inconel 625 Mesh: It is a high strength engineered material for outstanding corrosion and oxidation resistance at the elevated temperatures up to 1093oC or 2000oF. Inconel 718 Mesh: Alloy 718 is a precipitation hardened material for providing great high temperature corrosion resistance properties and mechanical strength. It has outstanding resistance to creeping and SCC up to 982oC.
Light duty steel mesh framed expanded polystyrene panel is made of polystyrene foam plastic plate, and both sides are coverd high tensile steel wire mesh panel.The steel wire mesh is diagonally inserted accross polystyrene plate with galvanized steel wire,3D EPS panel is connected by spot welding.Our products are followed our National Standard JGJ/T 269-2012. EPS Plate Main Performance Index Item Performance Index Test Way Apparent Density(kg/m3) 18~22 GB/T 6343 Thermal Coefficient [W/(m*K)] 0.039 GB/T 10294 or GB/T 10295 Compressive Strength 0.10 GB/T 8813 Tensile strength perpendicular to the direction of the plate (Mpa) 0.10 JG 149 Dimensional Stability (%) 0.50 GB/T 8811 Water Absorption (%)4 GB/T 8810 Class of combustion performance Not less than C class GB 8624 The thickness of EPS plate:50mm,70mm,100mm,120mm etc The width is 1200mm,and length 6000mm External dimension of EPS plate and allowable deviation should be accorded with below: External size(mm) Permissible deviation Length ,width 1000~2000 ±6.0 2001~4000 ±8.0 >4000 Positive deviation is not stipulated,-10 Thickness 50~75 ±2.0 76~100 ±3.0 >100 ±4.0 Diagonal difference 1000~2000 5.0 2001~4000 10.0 >4000 13.0 The steel wire mesh of 3D EPS plate and galvanized steel wire for inserting is adopt low carbon steel wire,and the standard value of tensil strength(fstk) is not less 550N/sqmm,the design of tensil strength(fy) is around 320N/sqmm, modulus of elasticity(Es) should adopt 2.0*105N/sqmm. The wire diameter of 3D EPS plate steel wire mesh is not less than 2.2mm,the mesh size is 50x50mm.Galvanized steel wire for inserting is not less than 3.0mm,others shouls accord to the rule of National Standard General purpose low carbon steel wire GB/T 343. The steel wire Main Technical Index Wire diameter Tensile Strength (N/sqmm) Reverse bending test( No) Zinc coated (g/sqm) Application Nominal Actual 2.2 2.23+0.05 550 6 ____________ Warp and weft wire for mesh 3.0 3.03+0.05 4 3.0 3.03+0.05 122 Steel wire 3.8 3.83+0.05 Note:Reverse bending test is the number of reversed bending 180 degrees. 3D EPS steel wire mesh panel permissible deviation Item permissible deviation (mm/10m) Length ±10.0 Width ±10.0 Diagonal difference ±10.0 Minimum tensile resistance of spot welding Item Wire between with wire of mesh panel Inserted steel wire between with steel wire mesh panel Wire diameter (mm) 2.2 3.3 3.0 and 2.2 3.8 and 3.0 Min Tensile strength of welding spot(N) 400 500 2140 3430 The3D EPS steel wire mesh panels tensile strength , elongation and cold bend of test way should be conform to the rule of Industry standard Technical specification for cold drawing of low carbon steel wire JGJ 19.
Z248.5/248.6/348.5/Z348.6/Z442.5/Z442.6/Z558.5/Z558.6 Grids and reinforcing meshes Reinforcing meshes is manufactured compliance with Swiss Standard SIA 16211 S550. It is different sides wire in the whole sheet as K188/K335 in longitudinal direction. Itâ??s used widely on construction footing foundation,flooring slabs,foundation beams,bridge and piers and tunnel of coal,mine,subway,and trian reinforced and support. Heyou wire mesh is a professional manufacturer for reinforcing meshes which can comply to Chinese standard ,Australian/New Zealand standard,Germany Standard, Normes Francaises,Swiss Standard, Osterreichische Norm etc. Our factory was approvaled by ISO.All the reinforcing meshes are follow to international standard.We have enough exporting experiences.Our salesman are more than 10years working experience in this fields. Our workers which has strong and skillfull are expert, they produce the reinforcing meshes better than tyro. They made reinforcing meshes has firmly welding spot,accurate wire diameter,mesh space and panel size,clearly ribbed,non rusted. The specification of reinforcing meshes conformance with Swiss Standard SIA 16211 S550 mesh type Pitch of wires(mm) diameter of wire(mm) Per meter area sqm/m Dimension of Mesh Area of Mesh(sqmm) Mass (kg/sqm) Weight of Mesh(kg) pL pC dL dC long cross L(mm) B(mm) K188 6 6 150 150 188 188 5000 2000 10 3.091 30.192 K335 8 8 150 150 335 335 5000 2000 10 5.372 53.72 Z248.5 6/4.5 7 150 150 248 257 5000 2000 10 3.422 34.22 Z248.6 6/4.5 7 150 150 248 257 6000 2000 12 3.472 41.668 Z348.5 7/5.5 8 150 150 348 335 5000 2000 10 4.628 46.28 Z348.6 7/5.5 8 150 150 348 335 6000 2000 12 4.694 56.326 Z442.5 8.0/6.0 9 150 150 442 424 5000 2000 10 5.857 58.57 Z442.6 8.0/6.0 9 150 150 442 424 6000 2000 12 5.94 71.282 Z558.5 8.5/7.5 10 150 150 558 524 5000 2000 10 7.315 73.15 Z558.6 8.5/7.5 10 150 150 558 524 6000 2000 12 7.418 89.014
K188/K335 reinforcement wire mesh Anping Heyou Wire Mesh Products Co.Ltd can supply reinforcement wire mesh conformance with Swiss Standard SIA 16211 S550. Its has widely useage for foudations beams,slabs,walls,columns,foundation slabs,footings,tunnel,coal and mine,subway tunnel etc. The mesh spacing is 150mm,and normal sheet size is 2m*5m. The skatch of K188/K335 reinforcement wire mesh NL= Number of longitudinal bars PL= pitch of longitudinal bars dL= diameter of longitudinal bars NC=Number of transverse bars L= length of longitudinal bar B=Length of transverse bar u1=Overhang of longitudinal bars u2=Overhang of longitudinal bars The specification of reinforcement wire mesh conformance with Swiss Standard SIA 16211 S550 mesh type Pitch of wires(mm) diameter of wire(mm) Per meter area sqm/m Dimension of Mesh Area of Mesh(sqmm) Mass (kg/sqm) Weight of Mesh(kg) pL pC dL dC long cross L(mm) B(mm) K188 6 6 150 150 188 188 5000 2000 10 3.091 30.192 K335 8 8 150 150 335 335 5000 2000 10 5.372 53.72 Z248.5 6/4.5 7 150 150 248 257 5000 2000 10 3.422 34.22 Z248.6 6/4.5 7 150 150 248 257 6000 2000 12 3.472 41.668 Z348.5 7/5.5 8 150 150 348 335 5000 2000 10 4.628 46.28 Z348.6 7/5.5 8 150 150 348 335 6000 2000 12 4.694 56.326 Z442.5 8.0/6.0 9 150 150 442 424 5000 2000 10 5.857 58.57 Z442.6 8.0/6.0 9 150 150 442 424 6000 2000 12 5.94 71.282 Z558.5 8.5/7.5 10 150 150 558 524 5000 2000 10 7.315 73.15 Z558.6 8.5/7.5 10 150 150 558 524 6000 2000 12 7.418 89.014 The details of the reinforcement wire mesh as below: Apparent three face indentation om the surface The weld spot firmly and strong Homogeneous mesh space Flat mesh surface The inspection of the reinforcement wire mesh The wire diameter inspected by micrometer The mesh space messured by bemier caliper The width messured by flexible rule The length messured by flexible rule The Tensile strength and yield stress inspected by tensile machine weld shear resistance test The packing and shipment The bundle of sheet size 2m x5m Shipment for loading container Application site of reinforcement wire mesh Reinforcement wire mesh used on bridge and pier Reinforcement wire mesh used on construction footing foudation Reinforcement wire mesh used on flooring slabs Reinforcement wire mesh used on foudation beams
SE92/SE82/SE72/SE62 concrete reinforcing mesh for structural using Heyou factory can produce concrete reinforcing mesh which is the specification of New Zealand standard AS-NZS 4761-2001. Details of concrete reinforcing mesh: Material:250N,500N,500L,300E,500E Mesh Pitch:200mm Wire:ribbed steel wire & plain steel wire Overhang length of two sides:100mm Wire diameter:6mm,7mm,8mm,9mm Size:2.4m*6m or 2.2m*5.8m Packing:1ton more or less per bundle HS code:73142000 Production Standard: AS-NZS 4671-2001 More feature of concrete reinforcing mesh as below: Signel-bar meshes Twin-bar meshes Plain concrete reinforcing mesh Ribbed concrete reinforcing mesh The ribbed is visible and deep notch. high quality steel bar as raw materials Resposibility worker for drawing,straightened and cut Electric resistance welding,the solder joint firmly and beautiful appearance Full auotamatic machine opreation,the panel size high accuracy, Neatly packing Big place and enough warehouse for stocks The specification of concrete reinforcing mesh as below concrete reinforcing mesh specification Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6x2.4m sheets Cross-sectional area/m width No. x dia., mm Pitch,@mm No. x dia., mm Pitch,@mm Unit area,kg/sqm Sheet,kg Longâ??l bars,sqmm/m Cross bars,sqmm/m Structural and skatch SE92 13 X9.0 200 30 X9.0 200 5.0 75 318 318 SE82 13 X8.0 200 30 X8.0 200 3.9 59 251 251 SE72 13 X7.0 200 30 X7.0 200 3.0 45 192 192 SE62 13 X6.0 200 30 X6.0 200 2.2 33 141 141 Non-structural SL51.5 17 X5.3 150 40 X5.3 150 2.2 32 147 147 SL41.5 17 X4.0 150 40 X4.0 150 1.3 19 84 84 Are you a Manufacturer? Heyou wire mesh factory as a professional factory for reinforcement mesh,which has 10 workshops,more than 200 workers,advanced production line,perfect production process, Strict production regulations. We own ourselves laboratory for inspected chemical composition and mechnical property of raw material,drawn wire diameter measuring,cutting wire length measurement ,and full pieces of concrete reinforcing mesh which contained pitch of wire to wire,shearing resistance,tensile strength,yeild strength,elongation,bend test,weight tolerance,size tolerance,ribbed height,pitch of transverse wire ribbed,surface quality and etc. We are strictly to do everything in order to guarantee our concrete reinforcing mesh quality. Therefore,Heyou Wire Mesh has a high reputation in our field as real manufacturer.
Concrete reinforcement mesh is classified ribbed concrete reinforcement mesh and plain steel wire concrete reinforcement mesh. The wire of ribbed concrete reinforcement mesh is 3 faces indentation.Please see figuer Concrete reinforcement mesh is always used on residential slabs and footing-construction and BCA complying with AS 2870,which is always paced in all reinforced conrete members to stop the concrete cracking. And F62/F72/F82/F92/F1018 concrete reinforcement mesh is old specification,was replaced by SL62/SL72/SL82/SL92/RL1018.For example:previously called F62(now SL62) is wire diameter 6mm bars welded together in a 200mm square grid.the panel size is 2.4m X6m. The Tensile strength is 300Mpa. The concrete reinforcement mesh specification as below: Reinforcing Mesh Code wire diameter aperture edge open width length weight per sheet(kgs) F62 5mm 200*200mm 200mm 2.4m 6m 20.92 F72 6mm 200*200mm 200mm 2.4m 6m 30.12 F82 7mm 200*200mm 200mm 2.4m 6m 41 F92 8mm 200*200mm 200mm 2.4m 6m 53.55
Hard drawn mesh is specified in AS/NZS 4671: 2001. Heyou wire mesh offers a range of mesh sheet sizes and certres to meet the needs of typical New Zealand applications. Our scope covers standard sheet sizes of 4.65m x1.97m and larger economical sheets 6.15m x2.42m. The pitches are 150mm x150mm or 300mm x 300mm. AS/NZS 4671: 2001 specification for hard drawn mild steel wire for concrete reinforcement The mechnical property required by standard AS/NZS 4671: 2001 Nominal diameter(mm) Minimum 0.2% proof stress(Mpa) Tensile strength(Mpa) Minimum Maximum Up to and including 3.15 485 575 855 Over 3.15 485 575 775 The pitch (a) of longitudinal bars and transvers bars is not less than 50mm. The pitch is measured as below shown. The tolerance of the pitch is not more than 0.075 times the specified value. Specification of hard drawn mesh Model Pitch / certres Wire dia.(mm) Length (mm) Width (mm) Newt cover (sqm) Heyou reinforcing item Cross section sqmm / m Mass per sqm kg / sqm No. of Longitudinal wire No. of Cross Wire Overhangs of Longitudianal wire Overhangs of Cross wire Weight (kg) 668 150 4.0 4650 1970 7.525 668L 83.8 1.315 14 31 75/75 10/10 12.44 665 150 5.3 4650 1970 7.525 665L 147.1 2.309 14 31 75/75 10/10 21.85 663 150 6.3 4650 1970 7.525 663L 207.8 3.263 14 31 75/75 10/10 30.87 665 150 5.3 6150 2420 12.760 665E 147.1 2.309 17 41 75/75 10/10 35.29 663 150 6.3 6150 2420 12.760 663E 207.8 3.263 17 41 75/75 10/10 49.86 662 150 7.1 6150 2420 12.760 662E 263.9 4.144 17 41 75/75 10/10 63.33 661 150 7.5 6150 2420 12.76 661E 294.5 4.624 17 41 75/75 10/10 70.67 300 Centres of hard drawn mesh 668 300 5.6 4950 2220 10.08 84/10 82.1 1.289 4*5.6mm+4*4.0mm 19 25/25 10/10 15.85 665 300 7.5 4950 2220 10.08 147/10 147.3 2.312 6*7.5mm+4*5.3mm 19 25/25 10/10 28.36 665 200 6.1 5050 2020 8.312 SE62 RES 146.1 2.294 11 26 25/25 10/10 24.79 665 200 6.1 5850 2420 11.93 SE62 146.1 2.294 13 30 25/25 10/10 34.10 665 300 7.5 6050 2420 11.58 SE73 147.3 2.312 9 21 25/25 10/10 36.51 665 300 7.5 5000 2270 10.08 SE73DE 147.3 2.312 8*7.5mm+2*5.5mm 19 7.5mm:25/255.5mm:25/25 10/10 30.69 664 200 7.0 5650 2220 10.432 SE72 192.4 3.02 12 29 25/25 10/10 39.93 662 200 8.0 5650 2220 10.432 SE82 251.3 3.946 12 29 25/25 10/10 52.16 661 200 9.0 6100 2420 12.76 SE92 318.0 4.99 12 29 25/25 10/10 71.65 Equivalents are based on the nominal sectional area of steel per meter width. Additional meshes specification are available as a special order.Minimum order quantities will apply. Please mail to us Heyou wire mesh for further details. What does SE62 mean? In standard AS/NZS 4671: 2001, the designates letters to be used to identify reinforcing mesh products:
Reinforcement steel mesh was welded by automatic electrical resistance welding machines conformance to standard AS-NZS 4761-2001. The material of reinforcement steel mesh is 250N, 500N, 500L, 300E, 500E. Reinforcement steel mesh is very poupular in civil engineering and construction. It always used on road subgrade, building foundation, tunnel support and reinforced,mine and coal reinforced and support, bridge construction etc. During construction works, It is not only increase our working speed and time but also save 75% construction cost and enhance the crack resistance. The specification of rectangular reinforcement steel mesh as below: Rectangular Reinforcing Mesh 2.4m*6m=14.4sqm Code Cross wire Longwire mm Mass/sheetkg Quantityin pack Pitch@mm No. x dia., mm Pitch@mm No. x dia., mm RL718 7.60 @ 200 30 x7.6 6.75 @ 100 25 x 7.6 68 20 RL818 7.60 @ 200 30 x7.6 7.60 @ 100 25 x7.6 79 20 RL918 7.60 @ 200 30 x7.6 8.55 @ 100 25 x 8.55 93 20 RL1018 7.60 @ 200 30 x7.6 9.50 @ 100 25 x9.5 109 15 RL1118 7.60 @ 200 30 x7.6 10.65 @ 100 25 x10.65 131 15 RL1218 7.60 @ 200 30 x7.6 11.90 @ 100 25 x11.9 157 10 The panel size 2.4m*6m is very pouplar in Australian market,but considered the transportation in container by sea and saved cost, we advise the customers to change the panel size to be 2.2m x5.8m.
Heyou factory can produce concrete reinforcing mesh which is the specification of New Zealand standard AS-NZS 4761-2001. Details of concrete reinforcing mesh: Material: 250N, 500N, 500L, 300E, 500E Mesh Pitch: 200mm Wire: ribbed steel wire & plain steel wire Overhang length of two sides: 100mm Wire diameter:6mm, 7mm, 8mm, 9mm Size: 2.4m * 6m or 2.2m * 5.8m Packing: 1ton more or less per bundle HS code: 73142000 Production Standard: AS-NZS 4671-2001 The specification of concrete reinforcing mesh as below concrete reinforcing mesh specification Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6x2.4m sheets Cross-sectional area/m width No. x dia., mm Pitch, @mm No. x dia., mm Pitch, @mm Unit area, kg/sqm Sheet, kg Long' l bars, sqmm/m Cross bars, sqmm/m Structural and skatch SE92 13 X9.0 200 30 X9.0 200 5.0 75 318 318 SE82 13 X8.0 200 30 X8.0 200 3.9 59 251 251 SE72 13 X7.0 200 30 X7.0 200 3.0 45 192 192 SE62 13 X6.0 200 30 X6.0 200 2.2 33 141 141 Non-structural SL51.5 17 X5.3 150 40 X5.3 150 2.2 32 147 147 SL41.5 17 X4.0 150 40 X4.0 150 1.3 19 84 84 Are you a Manufacturer? Heyou wire mesh factory as a professional factory for reinforcement mesh, which has 10 workshops, more than 200 workers, advanced production line,perfect production process, Strict production regulations. We own ourselves laboratory for inspected chemical composition and mechnical property of raw material, drawn wire diameter measuring,cutting wire length measurement, and full pieces of concrete reinforcing mesh which contained pitch of wire to wire, shearing resistance, tensile strength, yeild strength, elongation, bend test, weight tolerance, size tolerance, ribbed height, pitch of transverse wire ribbed, surface quality and etc. We're strictly to do everything in order to guarantee our concrete reinforcing mesh quality. Therefore, Heyou Wire Mesh has a high reputation in our field as real manufacturer.
Construction reinforcement mesh was made by plain steel wire. It main used on building construction complied with standard AS NZS 4671-2001. The material is 250N, 500N, 500L, 300E, 500E, the mesh size is 150x150mm, wire diameter is 5.3mm and 4.0mm and the overhang length is in both sides. These specificate is very pouplar in New Zealand civil engineering field. More features of construction reinforcement mesh and ours as below: 1. high quality raw material 2. electric resistance welding machine made it which has firmly solder join, size precision,and appearance good-looking 3. Professional management team 4. Complete QC rules and regulations 5. A full of laboratory testing instruments Advantage of construction reinforcement mesh by AS-NZS 4671-2001 standard: 1. Save 30% of steel bar dosages 2. Reduce 50%-70% work time, improve construction progress and shorten construction period. 3. Cut down 5%-10% construction cost 4. Used widely,it has a good market development prospects. The specification of construction reinforcement mesh by AS-NZS 4671-2001 standard as below: concrete reinforcing mesh specification Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6x2.4m sheets Cross-sectional area/m width No. x dia., mm Pitch, @mm No. x dia., mm Pitch, @mm Unit area, kg/sqm Sheet, kg Long' l bars, sqmm/m Cross bars, sqmm/m structural SE92 13 X9.0 200 30 X9.0 200 5.0 75 318 318 SE82 13 X8.0 200 30 X8.0 200 3.9 59 251 251 SE72 13 X7.0 200 30 X7.0 200 3.0 45 192 192 SE62 13 X6.0 200 30 X6.0 200 2.2 33 141 141 Non-structural SL51.5 17 X5.3 150 40 X5.3 150 2.2 32 147 147 SL41.5 17 X4.0 150 40 X4.0 150 1.3 19 84 84
Reinforcing mesh was made by deformed bar after drawn, which is accorded to Australian/New Zealand Standard AS-NZS 4671-2001. The material is 250N, 300E, 500L, 500N and 500E, the mesh spaces is 200mm, there is two sides overhang which is 100mm. the steel bar after drawing shape as below figure: 1. The angle of the rib or inclined indentation of the reinforcing mesh panels' bar isn't less than 45. The angle scope is greater than 45 and is less than 70, the rib height is from 0.025d to 0.10d. 2. The reinforcing mesh panel includes transverse and longitudinal bar, pitch and overhang. The Australian and new zealand's market, the normal panel size is 2.4m*6m.Because of containers size, we always advise our cutomer to make the panel size to be 2.2m*5.8m. It can be easy to be load and save more USD1000 per container for packing and loading cost. Steel pallet for reinforcing mesh size 2.4m *6m Loading container for reinforcing mesh sheet: 2.4m *6m 3.Each sheet of reinforcing mesh panel shall include number of bars,pitch,length,width, and overhang dimensions. And the bar arrangement of reinforcing mesh panel has single bars, twin bars or combination of single bars and twin bars. 4.The technical data of reinforcing mesh panle is contained composition and characteristic mechanical porperties of reinforcing steels. Notes: 1. Grade 250N is supplied as plain round reinforcing steel complying with AS 3679. 1, exceptthe tolerance of the diameter and roundness dosen't apply it. 2. For 500L steel bars, only requriement for wire diameter is less than 5.0mm is RekL 500 Material certificate of reinforcing mesh as below: Common size of Squre reinforcing mesh panel for Austialian Market Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6 x2.4 m sheets Cross-sectional area/m width No. x dia., mm Pitch@mm No. x dia., mm Pitch@mm Unit area kg/sqm Sheet, kg Long'l bars sqmm/m Cross bars sqmm/m Squre, with edge side-lapping bars SL102 10 x 9.5 + 4 x 6.75 200100 30 x 9.5 200 5.6 80 354 354 SL92 10 X 8.6 + 4 X 6.0 200100 30 x 8.6 200 4.6 66 290 290 SL82 10 x 7.6 + 4 x 6.0 200100 30 x 7.6 200 3.6 52 227 227 SL72 10 x 6.75 + 4 x 5.0 200100 30 x 6.75 200 2.8 41 179 179 SL62 10 x 6.0 + 4 x 5.0 200100 30 x 6.0 200 2.2 33 141 141 Squre, without edge side - lapping bars SL81 25 X 7.6 100 60 x 7.6 100 7.1 105 454 454 How can we conctrol our products quality for exporting Autralia? Firstly, we purchase the material from Steel Factory and inspect chemical composition and mechanical property of reinforcing mesh panel in our in-house laboratary according to AS 1554.3. Secondly, the panel size tolerances measure way as: a. Panel Size dimensions 6m in length, there is 40mm tolerances. b. Panel size dimensions 6m in length, the tolerance is �±0.7% c. Wire diameter and mesh size measure and weld shear resistance test conformance to AS NZS 4761-2001 and as per contract. d. Weigh the each bundle weight to calculate each panel weight.
The slab mesh reinforcement is used on footing construction, beam and piers of waffle rafts. The slab mesh was made by Heyou wire mesh factory accordance with AS NZS 4671-2001. the popular specification is SL102, SL92, SL82, SL72, SL63, SL53, L8TM, L11TM, L12TM in the Australia and New Zealand civil engineeing. The slab mesh reinforcement includes reinforcement mesh and trench mesh. Aoriding to different construction site, they use the spcification of slab meshes are difference. Slab mesh reinforcement for footing slab, beam and piers The full of slab mesh reinforcement specification as below: REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 Slab mesh reinforcement for footing slab, beam and piers RIBBED RECTANGULAR MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG RL718 6 x 2.4m Sheet 25 x 6.75 @ 100 30 x 7.60 @ 200 67 RL818 6 x 2.4m Sheet 25 x 7.60 @ 100 30 x 7.60 @ 200 79 RL918 6 x 2.4m Sheet 25 x 8.60 @ 100 30 x 7.60 @ 200 93 RL1018 6 x 2.4m Sheet 25 x 9.50 @ 100 30 x 7.60 @ 200 109 RL1118 6 x 2.4m Sheet 25 x 10.70 @ 100 30 x 7.60 @ 200 130 RL1218 6 x 2.4m Sheet 25 x 11.90 @ 100 30 x 7.60 @ 200 157 Slab mesh reinforcement for footing slab, beam and piers REINFORCING MESH TO AS/NZS4671:2001 / RIBBED SQUARE MESH 6.0 X 2.4 METRES Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG SL52 6 x 2.4m Sheet 10 x4.77 @ 200 + 4 x 4.00 @ 100 30 x 4.77 @ 200 21 SL62 6 x 2.4m Sheet 10 x 6.00 @ 200 + 4 x 4.24 @ 100 30 x 6.00 @ 200 33 SL72 6 x 2.4m Sheet 10 x 6.75 @ 200 + 4 x 4.77 @ 100 30 x 6.75 @ 200 41 SL82 6 x 2.4m Sheet 10 x 7.60 @ 200 + 4 x 5.37 @ 100 30 x 7.60 @ 200 52 SL92 6 x 2.4m Sheet 10 x 8.60 @ 200 + 4 x 6.00 @ 100 30 x 8.60 @ 200 66 SL102 6 x 2.4m Sheet 10 x 9.50 @ 200 + 4 x 6.75 @ 100 30 x 9.50 @ 200 80 SL81 6 x 2.4m Sheet 25 x 7.60 @ 100 60 x 7.60 @ 100 105 Slab mesh reinforcement for footing slab, beam and piers SQUARE MESH 300 X 300 SPACING TO AS/NZS4671: 2001 Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG SL53 6 x 2.4m Sheet 6 x 5.00 @ 300 20 x 5.00 @ 300 14 SL63 6 x 2.4m Sheet 6 x 5.00 @ 300 20 x 5.00 @ 300 21
Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam. Specification of trench mesh reinforcement Surface treatment:galvanized or drawn wire Material: R250N, D500N, D500L, D300E, D500E The Tensile strength is 300Mpa. The trench mesh was produced by standard AS NZS 4671-2001 Width: 0.2m - 2.3m Length: 6m REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 Trench mesh reinforcement for footing slab construction and Waffle rafts beam and piers And Alls of using is accordance to AS NZS 2870-2011. 1. Footing slap The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments. The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different. 2. Waffle rafts beam and piers The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft: (a). pier to be located on the intersection of every third internal beam. (b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.
We can supply good quality barbed wire and razor wire for security and fencing uses. Wire Materials: Galvanized steel wire, PVC coated iron wire in blue, green, yellow and other colors. Usage: Barbed Wire mainly serves in protecting of grass boundary, railway, highway and also widely used in military, jail, industry, agriculture, animal husbandry, dwelling house, plantation for fencing. Gauge of Strand and Barb in B.W.G. Approximate Length per Kilo in Meter Barbs Spacing 3" Barbs Spacing 4" Barbs Spacing 5" Barbs Spacing 6" 12x12 6.0617 6.7590 7.2700 7.6376 12x14 7.3335 7.9051 8.3015 8.5741 12-1/2x12-1/2 6.9223 7.7190 8.3022 8.7221 12-1/2x14 8.1096 8.814 9.2242 9.5620 13x13 7.9808 8.899 9.5721 10.0553 13x14 8.8448 9.6899 10.2923 10.7146 13-1/2x14 9.6079 10.6134 11.4705 11.8553 14x14 10.4569 11.6590 12.5423 13.1752 14-1/2x14-1/2 11.9875 13.3671 14.3781 15.1034 15x15 13.8927 15.4942 16.6666 17.5070 15-1/2x15-1/2 15.3491 17.1144 18.4060 19.3386
Steel Reinforcing Mesh Roll is used to provide tensile strength and crack control to structural concrete elements. Steel reinforcing mesh is the thin ribbed wire that can be make rolls presentation. Advantages to save more than 33% of steel, reducing costs 10% -30%; increase the speed of construction can shorten the duration of about 80%; to improve the quality of engineering structures, and concrete bonding anchoring reliable, smooth reinforcement bond strength equal to three times more, and the overall good, deviation is small, anti - cracking performance above 75%. Application Retaining and shear walls Beams and columns Concrete paving overlays Precast concrete elements Suspended floor slabs Swimming pool and gunite construction size(mm) 2.8-5.3 Reinforcement spacing(mm) Longitudinal wire 50-200mm Cross wire 30-1000mm Sheet size Length 2-50m Width 1-1.3m Mechanical and process property Meet GB/T1499.3-2002 standard;AS/NZS 4671; 2001,BS 4483:2005,A185-02
Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam. Specification of trench mesh reinforcement Surface treatment:galvanized or drawn wire Material: R250N, D500N, D500L, D300E, D500E The Tensile strength is 300Mpa. The trench mesh was produced by standard AS NZS 4671-2001 Width: 0.2m - 2.3m Length: 6m REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 And Alls of using is accordance to AS NZS 2870-2011. 1. Footing slap The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments. The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different. 2. Waffle rafts beam and piers The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft: (a). pier to be located on the intersection of every third internal beam. (b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.
