electronic potting silicon Rubber Characteristics 1. No toxicity, solventless, no odor or cure by-product. 2.No significant exotherm or shrinkage during curing. 3.Flexible curing schedule, can be cured at room temperature (R.T.) or at elevated temperature. 4.Very stable to changes of temperature, stability over wide temperature range (-50 to 200 C). 5.Good thermal conductivity. 6.Excellent dielectric properties for maintaining and protection of existing electrical insulation requirements. 7.Excellent weather resistance and waterproof property for protection from moisture and dust contamination. 8.Relative easier removal benefits to repair of electrical/electronic devices 9.Green environmental protection. Applicationof electronic potting silicon Rubber - high powered electronics - LED, LCD electronic display - circuit board - PCB substrate,etc - Precision Electronic Components, - DC/DC module and circuit board protection which requires high transparency and recovery. electronic potting silicon Rubber Warm Tips 1. The electronic potting silicon rubber should be sealed storage.The mixture should be used up at once, avoid causing waste. 2. The electronic potting silicon rubber belongs to non-dangerous goods, but keep away from mouth and eyes. 3. When electronic potting silicon rubber gets stratified after a period of storage, Please mix the electronic potting silicon rubber evenly before using, it does not affect the performance
Application: 1. To produce organic-si (si-oil, si-rubber) etc in chemical industry. 2. Regarding to the non-ferroalloyâ??s additive and deoxidizer. 3. It is applied to mechanical, chemical, alloys, electron, medicine industry, state defense etc. Chemical index: Item no. Si (% min) Fe (% max) Al (% max) Ca (% max) P 2202 99.5 0.2 0.2 0.02 30-60ppm 2502 99.5 0.25 0.25 0.02 30-60ppm 3303 99.3 0.3 0.3 0.03 30-60ppm 331 99 0.3 0.3 0.1 30-100ppm 3305 99 0.3 0.3 0.05 30-100ppm 441 99 0.4 0.4 0.1 40-100ppm 553 99 0.5 0.5 0.3 40-100ppm Size: 10-100mm 90ï¼?min or as per customerâ??s requirement Packing: in plastic woven bags of 1mt each or packed as per customerâ??s requirement -
Application: 1. To produce organic-si (si-oil, si-rubber) etc in chemical industry. 2. Regarding to the non-ferroalloyâ??s additive and deoxidizer. 3. It is applied to mechanical, chemical, alloys, electron, medicine industry, state defense etc. Chemical index: Item no. Si (% min) Fe (% max) Al (% max) Ca (% max) P 2202 99.5 0.2 0.2 0.02 30-60ppm 2502 99.5 0.25 0.25 0.02 30-60ppm 3303 99.3 0.3 0.3 0.03 30-60ppm 331 99 0.3 0.3 0.1 30-100ppm 3305 99 0.3 0.3 0.05 30-100ppm 441 99 0.4 0.4 0.1 40-100ppm 553 99 0.5 0.5 0.3 40-100ppm Size: 10-100mm 90ï¼?min or as per customerâ??s requirement Packing: in plastic woven bags of 1mt each or packed as per customerâ??s requirement -
Application: 1. To produce organic-si (si-oil, si-rubber) etc in chemical industry. 2. Regarding to the non-ferroalloyâ??s additive and deoxidizer. 3. It is applied to mechanical, chemical, alloys, electron, medicine industry, state defense etc. Chemical index: Item no. Si (% min) Fe (% max) Al (% max) Ca (% max) P 2202 99.5 0.2 0.2 0.02 30-60ppm 2502 99.5 0.25 0.25 0.02 30-60ppm 3303 99.3 0.3 0.3 0.03 30-60ppm 331 99 0.3 0.3 0.1 30-100ppm 3305 99 0.3 0.3 0.05 30-100ppm 441 99 0.4 0.4 0.1 40-100ppm 553 99 0.5 0.5 0.3 40-100ppm Size: 10-100mm 90ï¼?min or as per customerâ??s requirement Packing: in plastic woven bags of 1mt each or packed as per customerâ??s requirement -
Application: 1. To produce organic-si (si-oil, si-rubber) etc in chemical industry. 2. Regarding to the non-ferroalloyâ??s additive and deoxidizer. 3. It is applied to mechanical, chemical, alloys, electron, medicine industry, state defense etc. Chemical index: Item no. Si (% min) Fe (% max) Al (% max) Ca (% max) P 2202 99.5 0.2 0.2 0.02 30-60ppm 2502 99.5 0.25 0.25 0.02 30-60ppm 3303 99.3 0.3 0.3 0.03 30-60ppm 331 99 0.3 0.3 0.1 30-100ppm 3305 99 0.3 0.3 0.05 30-100ppm 441 99 0.4 0.4 0.1 40-100ppm 553 99 0.5 0.5 0.3 40-100ppm Size: 10-100mm 90ï¼?min or as per customerâ??s requirement Packing: in plastic woven bags of 1mt each or packed as per customerâ??s requirement -
Quick details Classification: chemical auxiliary agent Cas no.: 7631-86-9 Other names: silica gel powder Mf: sio2 Einecs no.: 231-545-4 Purity: 99% Place of origin: shandong, china (mainland) Type: adsorbent Adsorbent variety: silica gel Usage: coating auxiliary agents, petroleum additives, surfactants Brand name: bangkai Model number: industrial chemicals silica gel Raw material: silica gel Color: white Shape: powder Pore diameter: 60a Pore volume: 0.5-0.7ml/g Ph: negotiable Specific surface area: 450-600m2/g Loss on heating(150â??):
INTRODUCTION: It is a kinds of Two-parts silicone, part A is flowable liquid silicon, part B is curing agent/catalyst ,which gets cured at room temperature 25 Centigrade within 3-6 hours or heating curing.This product is perfect for cement,concrete stone, GRC and GFRC products' mold making,such as the flower pot,fountain,Polyurethane Wood Imitation,Reinforced Plastic,Garden Decorations,fiberglass product and other decoration industries. FEATURES: 1.High duplication times and no deformation 2.Excellent tear strength and tensile strength. 3.Good fluidity and good operability and good for both pouring method and pouring method. 4.Excellent flexibility and it is easy to demould. 5.It gets cured at room temperature 25 Centigrade within 3-6 hours. 6.Suitable hardness from 30 to 40 Shore A OPERATION OF SILICONE RUBBER FOR CEMENT CASTING: Step 1:Prepare the original mold Weigh silicone&curing agent according to the mix ratio recommended,than remember to stir silicone & curing agent evenly,otherwise the silicon rubber will be partly solidified and bring problems in your final operation. Whats more, the finished molds will meet a short life. Step 2:Vacuum pumping Without exception, this step takes less than 10 minutes. Otherwise, it will cause cross linking reaction, and no more further steps will be available. Step 3:Pouring casting or Brush operation Step 4:After 3-5 hours later,demoulding the silicone mold,It will be better to use the mould after 24 hours. APPLICATION: This silicone is suitable for statues' mold making. ABOUT US: We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber. What's more,our silicone rubber are environmental-friendly, with high safety and no toxic.You can absolutely trust your choice with us.
INTRODUCTION: This is a kind of room temperature vulcanized silicone rubber in condensation type. It's generally named as two part silicone rubber, Part A is a flowable liquid, part B is the curing agent or catalyst. It's mainly used for mold making. This Silicone rubber is with good fluidity and moderate hardness which is suitable for middle size product with pattern by pouring operation, especially popular for manufacturer of resin crafts and gypsum decoration. Besides, additive is available for brushing operation. It's one of our best selling silicone! PRODUCT FEATURES: *An exceptional fluidity and good operability, easy to demold *Moderate hardness *High tensile and tear strength *Good flexibility *Cure at room temperature *Outstanding bubble releasing *High duplication times OPERATION INSTRUCTIONS OF MANUAL MOLD DESIGN MAKING LIQUID SILICONE RUBBER RAW MATERIALS: Step 1: prepare the original molds Step 2: Take 100G parts A and add 3G parts B and mix them evenly. Step 3: Vacuum pumping Step 4: Pouring casting or Brush operation (For the detail of operation instructions,please contact us) SHELF LIFE : Twelve(12) months when stored under dry and cool place by original package under 25 Centigrade. APPLICATION: This silicone rubber is used for making molds of concrete stone,GRC, gypsum decoration, plaster ornaments, fiberglass products, polyester decoration, unsaturated resin crafts, polyresin crafts, polyurethane, bronze, wax, candle, and similar products . ABOUT US: We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber. What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.
INTRODUCTION: The component A of shoe Mold Silicone Rubber is white flowing liquid and the component B is the curing agent. For example, take silicone rubber of 100g and add 2% curing agent for mixing evenly. After the silicone rubber and the curing agent are completely mixed, put the silicon into a vacuum machine for deairing to remove the bubbles. After deaired, pouring the liquid silicone rubber into the product to be duplicated or into the mold frame. FEATURES: 1.Two-component silicone rubber with tin-catalyst 2.Cured under room temperature 3.Low shrinkage 4.Excellent fexibility & easy demould LIQUID RTV-2 SHOE MOLD SILICONE RUBBER NOTES: Shoe mold silicone rubber is used for pouring or brushing technique. That is to say, fix the product or sole model to be duplicated onto a plane plate, then enclose the plane frame with wooden plates to prevent the leakage of the silicon , mix the silicone rubber and the curing agent evenly according to the mixing ratio of 100 : 2 and pour them onto the sole model, then brush evenly with a wooden plate or a brush, and fill up the mold frame with gypsum after the silicone rubber is dried. APPLICATION: Shoe mold silicone rubber is mainly used for shoe molds, sand casting, sole sampling, plaster models, simple products, products with non-complex patterns, as well as product models with stable size and non-deformation. ABOUT US: We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber. What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us. For more information, welcome to contact Lilian: Wechat / Phone: 8613617490457 E-mail: lilian(at)xrsil(dot)com Skype: lilian-xrsilicone Company: Dongguan Xinrun Silicone New Materials Co., Ltd Xinrun Group Limited Factory address: No.2,Zhouliao Road, Langzhou Industrial Zone,Changping, Dongguan, Guangdong, China
INTRODUCTION: Silicone Foams is a soft, two-component platinum silicone flexible foam that is versatile and easy to use. Vibrant colors can be achieved by adding color pigments. Cured foam is high heat resistance (will resist up to 350°F/176°C), water resistant, UV resistant and resists oxidation and ozone degradation. FEATURE: 1.Mixed Viscocity 2.Very soft 3.Excellent temperature resistence IMPROVE SURFACE FINISH AND MINIMIZE VOIDS WITH BACK PRESSURE: Use a board that will completely cover the mold opening. Using a drill bit, drill 3 holes in the board spaced a few inches / cm apart. Make sure that, when the board is placed over the mold opening, the holes are over the mold cavity and rising foam will be able to make it through. Apply Ease Release 200 thoroughly too both sides of the board and into the drilled holes. Mix and pour foam into mold cavity and place board over mold opening. Hold board firmly in place. As foam rises in the mold cavity, some foam will grow out of the drilled holes. After the foam stops growing, you can let go of the board. Do not demold for at least 20 minutes. APPLICATION: Silicone Foams can be used for a variety of industrial and special effects applications including making foam filled appliances, padding/seat cushioning, orthotics/orthopedics, potting and encapsulation of electrical circuits and vibration dampening. ABOUT US: We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber. What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us. For more information, welcome to contact Lilian: Wechat / Phone: 8613617490457 E-mail: lilian(at)xrsil(dot)com Skype: lilian-xrsilicone Company: Dongguan Xinrun Silicone New Materials Co., Ltd / Xinrun Group Limited Factory address: No.2,Zhouliao Road, Langzhou Industrial Zone,Changping, Dongguan, Guangdong, China
FEATURES: -Mixing ratio of catalyst 2%-5% -Good flowability -Great self-deaeration -Very good heat resistance -High thermal conductivity -Outstanding release properties -High tear resistance -Low shrinkage -Outstanding resistance to inhibition -Good resistance to polyester resin and concrete SHELF LIFE: When stored at or below 32°C (89.6°F) in the original unopened containers, such silicone base and its curing agents have a usable life of 12 months. PACKAGE: Silicone Base is available in 1Kg, 5Kg, 20Kg, 25Kg and 200Kg containers. Curing Agents are available in 50g, 1Kg and 20Kg containers. APPLICATIONS: -Architectural Restoration -Sculpting/Wax Casting -Concrete/GRC Casting -Gypsum/Plaster Decoration -Polyester/Resin Crafts Molding -Furniture Molding -Candles Mold making -Soaps Mold making -Tire Molding -Detailed reproduction of figurines, art objects and similar items ABOUT US: We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber. What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.
Silicone Glass Lid/Glass Lid with Silicone Rim is a perfect fit for cookwares like pot and pan. Compared with traditional stainless rim glass lid, silicone rimmed glass lid has advantages like: * Dishwasher safe * Shattered-proof and protect both the lid and floor * More color options that go with the pot color * Heat resistant * Universal size lid can fit in 3 size pots * More stylish and elegant * Better sealing
Description of liquid silicone for soft relief gel insoles : OTT-X710 Liquid Silicone for Insoles is a solvent-free, flowable 2 Component RTV Silicone rubber. After mixing the X710 A and X710 B at a mix ratio of 1:1 the material will cure by an addition reaction at room temperature. The cure rate can be accelerated significantly by heat. Material has been especially developed for insoles. Application of liquid silicone for soft relief gel insoles : OTT-X710 silicone rubber is specially developed for insoles. It can also be used for lace coating and Conveyor belt coating and also for other applications where fast cure at elevated temperatures and good flow or self leveling characteristics are required. Using instructions of liquid silicone for soft relief gel insoles: 1. Applicable to the injection molding process 2. Mixing component A with B evenly according its mix ratio, it is ready for use after degassing, it cures by heating up the temperature when pouring into the mold. 3. The curing time is subject to the temperature, short time will be required under high temperature, long time will be required while the product with large thickness.
Feature of Transparent silicone micro tubes,silicone tube/ silicone tubing/ silicone hose 1. Pure silicone rubber, anti-oil and waterproof 2. Temperature resistance from -60~260 Celsius degree 3. Anti-aging, Ozone resistance, Insulating 4. No corrosion from copper and silver and so on. Application of Transparent silicone micro tubes,silicone tube/ silicone tubing/ silicone hose 1.Environmentally friendly non-toxic, in line with the ISO/ASTM 2.High tear resistance, low shrinkage, good resistance to anti-aging performance. 3.Generally used in medical equipment, home appliances, aerospace, military, 4.Automobile manufacturing, electronic components, transformers, motors, etc
Features of OTT Low Price Moulding Liquid Silicone Rubber: An exceptional fluidity and good operability, easy to demold Good tensile strength and tear strength Soft hardness Copy detailed pattern Good flexibility Eco-friendly Long shelf-time &lifetime Applications of OTT Low Price Moulding Liquid Silicone Rubber: OTT Low Price Moulding Liquid Silicone Rubber could be mainly used for PU/poly resin products, unsaturated resin products, plaster products, fiberglass products, gypsums crafts, cement statues, etc.
Fob price:us $3 - 50 / piece Min.Order quantity:50 pieces Supply ability:5000 pieces per day Port:shen zhen Payment terms:l/c, t/t, western union 1. Grade: silicone rubber thermal conductive insulation pad 2. Size: tc150 -tc400 3. Standard: lms tc 4. Certification: iso9001, sgs, cti, rohs Feature of silicone rubber thermal conductive insulation pad High compressibility, soft and flexible Natural stickiness, no extra surface frontal adhesives Good thermal conductivity, Meet with rohs standard High thermal conductivity High conformability to uneven surfaces at low stress application Electrical isolating very cost effective Application of high quality silicone rubber thermal conductive insulation pad 1. Heat sink your cpu/gpu 2. Switching power supply 3. Video equipment 4. Mobile equipment 5. Communication equipment 6.Between semiconductor/magnetic components and heat sinks. Packing details : packing, solid bicycle saddle, 50pcs/carton Delivery details : 3-30 days after order of solid bicycle tire tubes
1) Applications: OTT mold making liquid silicone rubber for plaster mold is primarily intended for poly resin crafts, PU crafts, PU resin crafts, gypsum crafts, unsaturated resin crafts, lighting and candles crafts , plastic toy, stationery gifts crafts industry, a large statue Buddha, relief, furniture, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils Factory, Europe componentfactory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on. 2) Description: OTT mold making liquid silicone rubber for plaster mold is white or red flowing liquid with general hardness of 22-50A after curing. Molding silicone is a kind elastic silicone which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength, tears strength and elongation.
Item FDA Manufacturer Wholesale Waterproof Custom Printed Logo Cartoon Silicone Baby Bib N.W. S:50g L:80g Material 100% silicone ROHS, FDA, LFGB, SGS,ISO. Size S:26x19.5x1.8cm L:32x22.3x3.3cm Color Red,green,yellow,light blue,deep blue and pink,or Pantone MOQ 1000pcs Price term FOB, CIF or EXW. Unisex Unisex Productions time According to the order. Place of Origin Huizhou,China. Package S:One pc/Opp bag ,200pcs/ctns.
Material: silicone Feature:Eco-Friendly, easy-cleaning,durable Style: Fashion Use:At home Function: Heat-resistance, protect foods stain babies' clothes Theme: bib Shape: Any shapes Regional Feature: Europe,USA Size: 29*19.5 Place of Origin: China (Mainland) Sample time: 3-7days Brand Name: OEM/ODM Eco-friendly: Yes Type: kitchenware Silicone baby bib
Liquid RTV Molding Silicone Rubber raw material for all kinds of mold making Features of liquid RTV Molding Silicone Rubber raw material for all kinds of mold making: 1. Two part of liquid fluid: liquid white silicone and curing agent. 2. Cure at room-temperature within 4-8 hours, but all performance will act perfectly when it cure within 2 - 4 hours. 3. Good fluidity and excellent operation. 4. Good resistance to weather, temperature, aging, acid. 5. Excellent tear strength, comfortable duplication times. Application of liquid RTV Molding Silicone Rubber raw material for all kinds of mold making: 1.Resin crafts, unsaturated resin crafts 2. Poly resin crafts, candle crafts, plastic crafts 3. Making molds forgypsum,GRC,concrete,Artificial stone products molding,Wax casting 4.Decoration building mold making 5.Lighting & candles crafts,stationery gifts,crafts industry 6.Casting for Statue,Buddha, Christmas ornaments,sculptures, figures etc Operation Instruction for Liquid RTV Molding Silicone Rubber raw material for all kinds of mold making : RTV-2 liquid mold silicone rubber is a kind of flowing liquid, and it consists of two component, part a is a flow-able liquid silicone rubber, part B is the curing agent. 1. Firstly, after your previous work of dealing with the original model, take some liquid silicone rubber, add 2%~3% cuing agent of the amount of silicon and mix themevenly. 2. Then after vacuum-pumping the mixture, you can pour it into the mold frame. 3. The silicone mold will cured in 2~3 hours. Note: the time for vacuum-pumping should be less than 3-5mins, otherwise, once the silicone rubber has cross-link reaction during vacuum. it will not be operated.