Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data
COLOUR : Red
FINISH : Matt
SOLIDS BY VOLUME : 40 �± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30�° C
RECOMMENDED DFT : 30-40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data :-
COLOUR : Red
FINISH : Matt
SOLIDS BY VOLUME : 40 �± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30�° C
RECOMMENDED DFT : 30-40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Recommended Use :-
Recommended over putty / primer applied surfaces for better gloss retention and aesthetics in topcoats.
Physical Data :-
COLOUR : Grey, White
FINISH : Egg Shell to Matt
SOLIDS BY VOLUME : 40 �± 3%
SPREADING RATE : 13.3 sq.mt / ltr at recommended DFT of 30 �µ
FLASH POINT : Base : 23�°C Hardener : 23�°C
DRYING CHARACTERISTICS (At 30�°C & 65% Relative Humidity) : SURFACE DRY : 20-30 minutes. HARD DRY : Overnight. FULL CURE : 7 Days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
This being intermediate, it is applied either over primer. The surface should be free from moisture, oil and dust before application. In case of aged epoxy / PU coating or exceeded over coating, the surface should be sufficiently roughened prior to painting.
Application Data :-
MIXING RATIO : Base: Hardener ( As per our recommendation)
APPLICATION : By Brush/ By Conventional Spray / By Airless Spray
THINNER : Type 290
POT LIFE : 4 hours min at 30�° C
RECOMMENDED DFT : 30 -35 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be top coated by PU, epoxy, Chlorinated rubber and synthetic enamel paints. Compatible with Epoxy and zinc rich primers.
Recommended Use :-
This product is a topcoat along with recommended undercoats for use in chemical plants, fertilizer plants, petrochemical and pharmaceutical complex, power plants, cement plants, steel plants, heavy chemicals and off-shore and on-shore industries.
It is recommended for very high chemical resistance and for areas not exposed to direct sunlight. Product is also recommended for application over suitable primer for OEM industry.
Physical Data
COLOUR : Assorted shades
FINISH : Glossy / Semi glossy / Matt
SOLIDS BY VOLUME : 40 ± 3% (Depends on shade)
THEORETICAL SPREADING RATE : 13.33 sq.mt / lt at recommended DFT of 30 µ
FLASH POINT : Base : Above 23 C Hardener : Above 23 C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 DAYS.
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
The surface of primer or intermediate coats, over which this product is applied as topcoat, should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 for better bonding.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional spray / By Airless Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30 C
RECOMMENDED DFT : 30-40 µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Two component air drying aromatic polyurethane finish coating
Recommended Use :-
It is recommended as topcoat for Original Equipment Machines, Hygienic, Maintenance painting where mild chemical resistance along with good abrasion resistance and decorative finish are required. Sometimes it is recommended as undercoat of finish coats application for economic benefits.
Physical Data
COLOUR : Assorted shades
FINISH : Glossy / Semi glossy / Matt SOLIDS BY
VOLUME : 40 �± 3% (Depends on shade) THEORETICAL
SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30
FLASH POINT : Base : Above 23C Hardener : Above 30C
DRYING CHARACTERISTICS : SURFACE DRY :20 - 30 minutes (At 30C and 65% Relative humidity) HARD DRY : Overnight FULL CURE : 7 days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
This being a Topcoat, which is applied over underneath primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 followed by solvent wipe for better bonding.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional spray / By Airless Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30 C
RECOMMENDED DFT : 30-40
OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours
COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
5642 Paints Coatings Suppliers
Short on time? Let Paints Coatings sellers contact you.
Two-component Air Drying Acrylic Aliphatic, Non Yellowing polyurethane finish coating.
Recommended Use :-
This product has excellent weathering resistance additionally it offers excellent resistance to various industrial chemical fumes and splash. This product is recommended as topcoat with suitable primers and undercoats for use in High Chemical & Saline atmosphere for better aesthetics and corrosion resistance in Chemical, Fertilizers, Petrochemical, industrial plants and also for premium industrial equipments. Not recommended for immersion application.
Physical Data
COLOUR : Industrial Shades
FINISH : Glossy / Semi-glossy
SOLIDS BY VOLUME : 40 + 3% (Depends on shade)
THEORETICAL SPREADING RATE : 13.33 sq.mt / ltr @ recommended DFT of 30
FLASH POINT : Base : Above 23 C Hardener : Above 23C
DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.
Application Data :-
MIXING RATIO : Base: Hardener - As per our recommendations
APPLICATION : By Brush / By Conventional Spray / By Airless Spray
THINNER : Type 290
POT LIFE : 4 hours min at 30C
RECOMMENDED DFT : 30- 40 .
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Various interior and exterior paints.
All eco-friendly products
Same quality as European products while nearly a half price from their prices
30 years of know-how and experiences
We are producing Anti-corrosive Paint and Industrial Paint.
We have a vision of Paints for the future.
Our mission is to produce suitable products with long term durability that can meet customer's requirement.
For the future of our customers We would like to bring to our customers the most satisfaction about quality and after sale service.
For the future of paint We always aim for better technology, supply improved products better than yesterday.
Theaoson all purpose foamy cleaner is a water-based formula, rich in foam, made of natural green plant-synthesized surfactants and the latest high-tech formulas. It has fast penetration, strong detergency and super deep cleaning efficiency, and can remove any stains easily. This product does not contain phosphate, it is harmless to the environment, the foam is delicate and rich, the smell is aromatic, and it is safe and convenient to use.
It is a water-in-oil system formula, which integrates infiltration, cleaning and glazing at one time. It is rich in cleaning foam, which can effectively remove oil stains and dirt on the treated surface. After use, it can restore the luster of the surface and restore it as new.
Theaoson sticker remover is composed of aerosol can, aerosol valve, paint solution and propellant. This product uses mild remove formula, can effectively dissolve the surface colloid of the removed object, do not corrode the surface of the object, spray and wipe just once, easy to remove.
Description of the product- Acrylic based texture finish permitting various interesting texture finishes to be created on masonry surface with a touch of class
Area of Use (Application)- All interior and exterior building surfaces
1. Technologically advance, specially formulated from 100% acrylic co polymet/quartz/minerals and additives provides a flexible, breathable water repellant decorative texture with built in long life and durability to enhance and beautify
2. Tuff stuff texture coats bonds/adhere perfectly to substrate and are strong enough to withstand abrasion and extreme temperatures, acid UV and fungus growth.
3. Seals hairline cracks hence prevents water seepage
1. Easy to mix with water and forms soft consistency paste which makes it easy to fill the joints
2. Excellent UV resistance and durability enables the product use for exterior application
3. Available in shades
Aristo Multipurpose Spray Paint is acrylic resin base aerosol paint for general purposes, it has excellent weather resistance and strong adhesive power, easy to spray with minimal loss, can be widely used in spray and repairing of surfaces of metal, wood, glass, leather, porcelain, ABS plastic and many kinds of materials.
For your ref., this is Sherry from Aristo Industries in China. our plant passed BSCI audit, supplying Wal-Mart, Home-Depot, Hobby-Lobby, Michels for some years, our main lines including aerosol paints, auto care aerosols, lubricants, cleaners, adhesive sprays, polyurethane foam, sincerely hope we can bring value for you team in the coming future.
Gold Acrylic Metallic Paint is a low odour, water-based acrylic paint which can be applied to concrete, gypsum, wood and also metal to provide a gold effect finish.
It is formulated for application by roller, brush and spray, providing a uniform distribution of metallic gold pigment across the substrate, giving a smooth finish.
Features
Low odour, environmental-friendly
Smooth, metallic effect finish
Easy to apply
Fast dry
5642 Paints Coatings Suppliers
Short on time? Let Paints Coatings sellers contact you.
