Industrial Paint And Thinner

A. PRODUCT DESCRIPTION:
These are Paint thinners. These are designed to improve the flow of a range of MARLAC Paint products. Can also be used as a cleaner for metal cleaning, pumps and tools before and after applications.
B. TYPICAL USE:
Suitable as Thinner for :
1)Alkyd and Oil based Paints
2)Epoxy Paints
3)Polyurethane paints
4)All types of Stoving and Air drying paints
5)Cleaning thinner
C. COLOUR:
Colourless clear liquid.
D. PRODUCT DATA:
(a) Boiling Range : Calculated
(b) Flash Point : As Per Std
(c) Density : 0.85 + 0.1
The data may slightly vary depending on the properties of the RM Solvents used.
E. PACKAGING:
5 or 20 Lt Drum
F. STORAGE:
The material must be stored as per the regulations. Keep the containers in Dry, Cool, Well Ventilated
space and away from the source of Heat and ignition. Containers must be kept tightly closed. Handle with care.
G. SHELF LIFE:
Minimum 12 months, provided stored properly.
H. HEALTH AND SAFETY:
Please follow the precautionary advices on the container. Use under well ventilated conditions. Do not
inhale spray mist. Avoid Skin contact. Spillage on the skin should immediately be removed with
suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought
immediately.
I. DISCLAIMER:
The information in this document is given to the best of MIPPLâ??s knowledge, based on the laboratory
testing and practical knowledge. MIPPL reserves the right to revise the data without further notice.
Users should always consult MIPPL for specific guidance on the general suitability of this product for their needs and specific practices.

SU-EPO-PRIME 10: is a two pack polyamide-cured epoxy primer containing Zinc Chrome as a corrosion inhibiting pigment. Primer is designed to give outstanding corrosion resistance and adhesion. It cures to a hard and tough film with excellent physical and mechanical properties. This product is universally recommended for direct application on Ferrous metals, suitably treated light alloys or galvanized surfaces, after proper surface preparation. Primer can be overcoated with epoxy and polyurethane intermediate coats and top coats. Two pack Epoxy-polyamide Zinc Phosphate Red Oxide Primer, direct application on ferrous metals.

2) SU-EPO-PRIME 20: is a two component Epoxy cold cured Zinc Chromate Primer with outstanding corrosion resistance and adhesion. Primer cures to a hard and tough film with excellent physical and mechanical properties. This product is universally recommended for direct application on Ferrous metals, suitably treated light alloys or galvanized surfaces, after proper surface preparation. Primer can be overcoated with our epoxy and polyurethane intermediate coats and top coats.

3) SU-EPO-PRIME 30: is a two component Epoxy cold cured Zinc Phosphate primer with outstanding corrosion resistance and adhesion. Primer cures to a hard and tough film with excellent physical and mechanical properties. This product is universally recommended for direct application on Ferrous metals, suitably treated light alloys or galvanized surfaces, after proper surface preparation. Primer can be overcoated with our epoxy and polyurethane intermediate coats and top coats.

4) SU-EPO-PRIME 31: is a two pack Epoxy cold cured Zinc Phosphate primer with high film build outstanding adhesion and corrosion resistance. Primer cures to a hard and tough film with excellent physical and mechanical properties. It is ideal for application in areas where higher thickness is recommended for achieving optimum performance. This product is universally recommended for direct application on mild steel or suitably treated light alloys or galvanized surface, after proper surface preparation.

5) SU-EPO-PRIME 32: is a two pack high solids polyamide cured epoxy resin surface tolerant primer with outstanding corrosion resistance. Primer contains good amount of anticorrosive pigment. It is ideal for application in areas where higher thickness is required for achieving optimum performance. The primer can be over coated with epoxy, chlorinated rubber or polyurethane topcoats. Primer has good adhesion to steel, galvanized steel and non ferrous metals.

6) SU-EPO-PRIME 40: is a two pack epoxy polyamide clear primer, recommended for direct application on concrete & wood substrates.

HI - Performance Syn. Enamel Paint
Superior Durability Color Pigment System
Easy To Apply By Brush , Roller And Spray

PRODUCT PARAMETERS
1. Type : Single Pack
2. Composite : Modified Oil Based Resin with Finest Bright
Pigments, Hydrocarbon solvent and addives
3. Use Recommended Thinner to make
Applicaon Viscosity
4. Applicaon Tools : Brushing, Spraying or
Roller
5. Flash off = 30 Minutes
6. Drying Time :
Surface Dry : 4 Hours
Hard Dry : Overnight
7. Curing Time : 72 hours
8. Over coang Interval : MIN : Overnight
MAX : 5 Days
9. Color : Assorted Shades
. Finish :
10 Smooth Finish
11 Thinner / Cleaner KISOMIN THINNER
12. Shelf Life: Up to 12 Months as long as the sealed containers
are kept under cover in a dry place under normal
temperature.

SCOPE
USES
Kisomin durable synthec enamel are long lasng & solvent based
paint used for wide range of surface.
Recommended as a decorave finish coat & can be applied on
surfaces like Metal, Cement Brickwork, Asbestos Grills and Wooden
surfaces like doors, Windows, Cabinets & wide range of furniture

FEATURES/ BENEFITS
* Smooth durable finish.
* Smooth flow & easy to apply.
* Excellent coverage & hiding.
* Superior surface protecon.

KEY ATTRIBUTES
* Applicaon temperatures : 10-44 degc

PERFORMANCE PROPERTY
Chemical Resistance
A Exposures Splash & Mild Fumes/Outdoor
Spillage Resistance
cid + +
Alkalis + +
Solvent NA NA
Salt ++ ++
Water +++ +++
Flexibility +++
Adhesion +++

Excellent : +++
Very Good : ++
Good : +

SURFACE PREPARATION
APPLICATION
BRUSH
CONVENTIONAL SPRAY
NOTES :
HEALTH & SAFETY
Steel : Sand the surface with coarse Sand / water paper according to the type of surfaces to remove rust, dust & other foreign parcles. System of
Coang should be selected depending upon the type of substrate. Wipe to clean the surface. Apply single coat primer & allow to dry. Re sand the
surface with Sand paper & wipe to clean. Apply 2nd Coat of primer & allow drying for overnight. Before applicaon of paint, thin down to achieve
desired viscosity & filter through white cloth. Apply Kisomin Paint to finish.
Sr the base thoroughly and then mix to uniform consistency.
Apply without thinning
Add Kisomin thinner to adjust viscosity depending on spray condion. Use any standard equipment at an atomizing pressure of 3.5-4.5 kg/cm�².
1. Use off the mixed paint .
2. Do not apply when temperature falls below 10 C or rises above 50�°c and when relave humidity rises above 90%. Do not apply during rain, fog or mist
3. Brushes and spray equipment should be cleaned with Thinner,
4. Special care to be taken to close immediately the partly used Diluted Material.
Please refer to the separate Material Safety Data Sheet available with detailed information