Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module description Quickly integrate hydrogen sulfide sensing into your system with very low power consumption and a simple analog sensor signal output. The ulpsm converts the hydrogen sulfide sensors linear current signal output to a linear voltage signal, while maintaining the sensor at its ideal biased operation settings. Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module benefits 0 to 3 v analog signal output Low power consumption < 45 uw Fast response On-board temperature sensor Easy sensor replacement Standard 8-pin connector Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module applications Fixed industrial safety monitoring Portable industrial safety monitoring Portable personal safety monitor Indoor air quality monitoring Outdoor air quality monitoring Bad breath/halitosis sensing Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module performance characteristics Measurement range: 0 to 50 ppm Lower detection limit: 0.3 ppm Resolution: 0.15 ppm Accuracy: < â± 2 % of reading Response time t90: < 30 seconds Power-on stabilization time: 60 minutes recommended
4nd citicel nitrogen dioxide sensor key features & benefits , industry leading reliability , improved performance variability 4nd citicel nitrogen dioxide sensor application Industrial safety: sensors for portable gas detectors used in industrial hygiene and confined space entry. 4nd citicel nitrogen dioxide sensor performance characteristics , nominal range: 0-20 ppm , expected operating life: two years in air , output signal: 0.6 , ± 0.15 ua/ppm , resolution: 0.1 ppm , repeatability:
Nh3-3e100se ammonia sensor nh3 sensor description Nh3-3e100se ammonia sensor, 3 electrode sensor; available in mini, classic, 4-series and 7-series formats. Nh3-3e100se ammonia sensor nh3 sensor features Amperometric 3 electrode sensor cell Very stable zero reading Very selective Highly sensitive Hydrous electrolyte Nh3-3e100se ammonia sensor nh3 sensor typical applications Tlv-monitoring, leakage detection Portable & fixed point applications Food & refrigeration industry, general industry, semiconductor industry Nh3-3e100se ammonia sensor nh3 sensor technical specifications Measuring range: 0-100 ppm Sensitivity range: 130 na/ppm â± 30 na/ppm Resolution at 20â°c: < 1 ppm Linearity: < 10% full scale Operation temperature range: -20â°c to +40â°c Operation humidity range, : 15-90% r.H, non-condensing
Sg01l-5lens Concentrator lens sic based uv photodiode avirtual = 55 mm2 Properties of the sg01l-5lens uv photodiode Broadband uva+uvb+uvc, ptb reported high chip stability, for flame detection Radiation sensitive area a = 55 mm2 To5 hermetically sealed metal housing with concentrator lens, 1 isolated pin and 1 case pin 10âµw/cm2 peak radiation results a current of approx. 700 na Sg01l-5lens uv photodiod specifications Sensitive area: 55 mm2 Dark current: 3.5 fa Capacitance: 250 pf Responsivity range: 221 - 358 nm Operating temperature: -55 ~ +170â°c Storage temperature: -55 ~ +170â°c Soldering temperature (3s): 260â°c Reverse voltage: 20 v
Spd005gasmd 5 psi gauge pressure sensor with analogue output description This pressure sensor has an amplified analogue output. The sensor is compensated for offset, sensitivity, temperature drift and nonlinearity. The sensor is available in the range from 5 to 100 psi. Other ranges on request. Available in gauge and absolute type. The output is ratiometric to the power supply voltage. 5 v power voltage the output span is 0.5 to 4.5 v. The spd analogue series can be considered as an "analogue" successor of the spd series. Spd005gasmd 5 psi gauge pressure sensor with analogue output electrical characteristics Performance characteristic at vcc =5v excitation 25â°c. Supply voltage: 4.75~5.5v Supply current: max. 3ma Pressure range: 0~5psi Accuracy: â±1.8%fs Operating temâ??perature: -20~85c Storage temperature: -40~125c
O2-M2 Oxygen Sensor Description Alphasense Oxygen sensors use capillary flow control. Unlike partial pressure oxygen sensors, they have good pressure and temperature dependence, making them the best choice in safety applications. Standard galavanic sensors use lead for greatest reliability but fixed lifetime. Specifications * Output: 80 to 120 uA @ 20.9% O2 * Response time t90: < 15 (s) from 20.9% to 0% O2 * Linearity: 0.6 % O2 deviation @ 10% O2 * Operating life: > 24 months *Temperature range: -30 to 55 'C * Pressure range: 80 to 120 kPa * Humidity range: 5 to 95 % rh continuous * Diameter: 20.0 mm (including label) * Heigh: 17.4 mm (including foam ring) * Weight: < 16g
Sonic-anemo-dzp ultrasonic wind speed sensor description: Sonic-anemo-dzp ultrasonic anemometer is powered by its own solar panel. It is well suited to remote installations where power consumption matters. This unit connects directly to a pulse or potentiometer input (i.E. On davis instruments). It is a useful product for professionals, integration to aws (autonomous weather station), and well-informed users. Sonic-anemo-dzp ultrasonic wind speed sensor specification: , output rate: 1 measure and update per second , wind module sensitivity: 0.12 m/s , wind module resolution: 0.05 m/s , wind module dynamic: 0.12 to 40 m/s , direction sensitivity: +/-1.5' , direction resolution: 1' (9 bits) , power supply: photovoltaic panel, battery lifepo4 , op. Temp. Without icing: -15'c to +55'c
Do1200 and do1200tc dissolved oxygen sensors Item no.: do1200/h, do1200/t, do1200tc/h, do1200tc/t, 971598, 971598tc Do1200 dissolved oxygen sensor features * reliable galvanic sensing technology * compact 12mm design * for portable, laboratory or on-line use * optional integral atc element * easy to use pre-membraned replacement caps Do1200 dissolved oxygen sensor description The do1200 and do1200tc feature dependable galvanic technology. No warm up period is required. Sensors are supplied with fast responding hdpe membrane caps for portable or lab use. Optional ptfe membrane caps are available for on-line or heavy uv exposure applications. Fill solution is replaceable when required. The do1200 is supplied without internal temperature compensation. The do1200tc can be supplied with a variety of user defined atc elements. Standard cable length is 2.5 feet with a tinned lead termination. Longer cable lengths and connectors are available for an additional charge. For on-line use, our fc75p 3/4 inch in-line fitting may be ordered to provide for mounting into 3/4 inch fnpt threaded tees. Do1200 dissolved oxygen sensor specifications * range: 0-20 mg/l * body material: epoxy and noryl * max temperature: 50 degrees c * saturation output: hdpe = 47mv +/- 9mv, ptfe = 33mv+/-9mv * pressure: 0-100 psig (7.5 bar) * calibration: single point in air * response time: after equilibration, hdpe 1 minute for 2mv, ptfe 2 minutes for 2mv
Mb7139 xl-trashsonar-wr High performance ultrasonic trash bin measurement Mb7139 xl-trashsonar-wr ultrasonic sensor product description The mb7139 xl-trashsonar-wr1 is a weather resistant sensor designed for trash bin level measurement. The mb7139 xl-trashsonar-wr1 reports the range to the first detectable target in a trash bin. This sensor is our most recommended sensor for testing within trash bins. High output acoustic power combined with continuously variable gain, real-time background automatic calibration, real-time waveform signature analysis, and noise rejection algorithms results in virtually noise free distance readings. This holds true even in the presence of many of the various acoustic or electric noise sources. The xl-trashsonar-wr sensors are factory calibrated to match narrow sensor beam patterns and provide reliable mid-range detection zones. Mb7137 is the i2c version of this sensor. Mb7139 xl-trashsonar-wr ultrasonic sensor product specifiations Resolution of 1 cm 10hz read rate 42khz ultrasonic sensor measures distance to objects Rohs compliant Read from all 3 sensor outpus: analog voltage, pulse width, rs232 serial Operates from 3.0-5.5v Operational temperature from -40'c to +65'c Maximum range of 350 cm (138 inches) Mb7139 xl-trashsonar-wr ultrasonic sensor features and benefits Real-time calibration, noise rejection and additional filtering provides stable range information Excellent for applications that require consistently accurate outputs Impressive acoustic and electrical noise resistance Mb7139 xl-trashsonar-wr ultrasonic sensor applications and uses Autonomous navigation Environments with acoustic and electrical noise Bin level measurement Tank level measurement Trash level measurement
SONIC-ANEMO-DVC Ultrasonic Wind Speed Sensor Description: As Worldwide Premiere launch, a specific version of the CV7-V which connects directly to the wind sensor input on Davis instruments. This sensor will allow the replacement of mechanical anemometers / wind vanes with no need of anything else but power supply. Itâ??s an exclusive and useful product for both, professionals and well-informed amateurs. SONIC-ANEMO-DVC Ultrasonic Wind Speed Sensor Specification: * Output rat: 2 Hz / 30 Hz measurement * Wind module sensitivity: 0.12 m/s * Wind module resolution: 0.05 m/s (16 bits) * Wind module dynamic: 0.12 to 40 m/s * Direction sensitivity: +/-1.5' * Direction resolution: 1' (9 bits) * Power supply: 2.7 V to 35 V DC * Electrical consumption: 2.6 mA Avg. @ 12 V * Op. temp. without icing: -15'C to +55'C
Y504-A Dissolved Oxygen Sensor Description The sensor is based on optical fluorescence lifetime quenching technique. Its technical procedure meets ASTM D888-09 standard for optical sensing of dissolved oxygen. This online sensor is developed to integrate with Yosemite wireless monitoring system. Its rugged design and large measurement range make it ideal for sampling, flow cell, ground water and waste water measurements. Y504-A Dissolved Oxygen Sensor Applications Fish farmer, waste water plant, river, stream, and ocean monitoring Y504-A Dissolved Oxygen Sensor Feature * 0-20mg/L or 0-200% Saturation * 0~50 'C; IP68 rating * Membraneless, no electrodes design * No oxygen consumption * Flow Independent * Automatic temperature compensation * No H2S Interference * Low Drift, fast response, and more accurate * Low Maintenance, low operating cost * Easy sensor cap replacement * RS-485; MODBUS protocol compatible Y504-A Dissolved Oxygen Sensor Technical Specifications * Range: 0-20mg/L or 0-200% Saturation * Response Time: 10 sec * Housing IP Rating: IP68 * Accuracy: 1% * Drift: -
SONIC-ANEMO-SDI Ultrasonic Wind Speed Sensor Description SONIC-ANEMO-SDI is made from the CV7-V to which a SDI12 protocol and optimizing electrical consumption has been added. Sample rate is 2 Hz. This ultrasonic wind sensor operates in a request-response mode. This product is more energy-efficient than standard units. The SONIC-ANEMO-SDI is dedicated to meteorological applications. SONIC-ANEMO-SDI Ultrasonic Wind Speed Sensor Available data: - Average speed and direction over 10 minutes - Minimum wind speed and direction for that period - Maximum wind speed (gust 3s) and direction for that period - Software version and serial number - Data measurement quality rate from the sensor - Data for sensor diagnostic (manufacturer use only) SONIC-ANEMO-SDI Ultrasonic Wind Speed Sensor Specification: * Output rate: 2 Hz / 30 Hz measurement * Wind module sensitivity: 0.12 m/s * Wind module resolution: 0.05 m/s * Wind module dynamic: 0.12 to 40 m/s * Direction sensitivity: +/-1.5' * Direction resolution: 1' * Power supply: 2.7 V to 35 V DC * Electrical consumption: 2.9 mA Avg. @ 12 V * Op. temp. without icing: -15'C to +55'C -
CV7-OEM Ultrasonic Wind Speed Sensor Description CV7-OEM shows the same features as the CV7 standard: light, compact and low energy consumption. With this OEM version of the Static Wind Transducer CV7, you can add an accurate Ultrasonic Wind Sensor to your own products and installations. It is powered by 8-30 VDC power supply and it outputs RS232/RS422/NMEA0183 signal. CV7-OEM Ultrasonic Wind Speed Sensor Specification: * Output rate: 2 Hz / 30 Hz measurement or *4 Hz / 60 Hz meas. * Wind module sensitivity: 0.12 m/s * Wind module resolution: 0.05 m/s * Wind module dynamic: 0.12 to 40 m/s * Direction sensitivity: +/-1.5 degree * Direction resolution: 1 degree * Power supply: 8 V to 30 V DC * Electrical consumption: 9 mA * Op. temp. without icing: -15 degree C to +55 degree C -
CV7-E Ultrasonic Wind Speed Sensor Description The CV7-E is easily integrated into measurement and monitoring systems. Detects gusts with great responsiveness and low latency. The CV7-E is powered by 8-30 VDC power supply and it outputs RS232 / RS422 / 5 V level signal / NMEA0183. The CV7-E shows a data rate twice faster than the CV7 and CV7-V with a data output 4 per second. The small size of this sensor makes it very discreet. Like every LCJ Capteurs products, CV7-E is energy efficient. CV7-E has proved its value with universities â??laboratories, scientific and wind tunnels successful tests. It can be used connected to a PC and to any system featuring a NMEA® input port. CV7-E Ultrasonic Wind Speed Sensor Specification: * Output rate: 4 Hz / 60 Hz measurement * Wind module sensitivity: 0.12 m/s * Wind module resolution: 0.05 m/s * Wind module dynamic: 0.12 to 40 m/s * Direction sensitivity: +/-1.5 degree * Direction resolution: 1 degree * Power supply: 8 V to 30 V DC * Electrical consumption: 9 mA * Op. temp. without icing: -15 degree C to +50 degree C -
Y511-A Turbidity Sensor Description Automatic cleaning turbidity sensor is complied with ISO 7027 Turbidity Standard. The turbidity sensor can be deployed in-situ and provide very stable data over long period of usage, which helps to ensure the quality of your measurements. Y511-A Turbidity Sensor Typical Applications Water quality monitoring, waste water testing, process water and aquaculture monitoring. Y511-A Turbidity Sensor Features * 0.1~1000 NTU * Accuracy -
IRceL CH4 NDIR CH4 Sensor Description Miniature infrared sensor with on-board EEPROM and thermistor IRceL CH4 NDIR CH4 Sensor Key Features & Benefits: * Integrated thermistor for accurate temperature compensation * EEPROM programmed with sensor specfic performance characteristics * Compact Size IRceL CH4 NDIR CH4 Sensor Technical Specifications * Operating Principle: Non-Dispersive Infra-Red * Measurement Range: 0-5% vol. Methane * Accuracy (-20'C to +50'C): Within ± (0.1% vol CH 4 + 4% of concentration)â?? * Response Time (T90): < 35 Seconds * Supply Voltage: 3-5 VDC, 3.3 V to utilise EEPROM calibration * MTBF: > 5 years -
MICROceL CF Carbon Monoxide Sensor (CO sensor) Description MICRO 3-electrode carbon monoxide sensor with inboard filter. MICROceL CF Carbon Monoxide Sensor (CO sensor) Key Features & Benefits * A robust carbon monoxide sensor suitable for portable life safety applications * Extremely small size MICROceL CF Carbon Monoxide Sensor (CO sensor) Technical Specifications * Operating Principle: 3-electrode electrochemical * Measurement Range: 0-500 ppm CO * Sensitivity: 0.045 ± 0.01 uA/ppm * T50 Response Time: -
MB7040 I2CXL-MaxSonar-WR High Performance Ultrasonic Precision Rangefinder MB7040 I2CXL-MaxSonar-WR Ultrasonic Rangefinder Product Description Weather Resistant (IP67) Sensors, and Optional Chemical Resistance The industrial outdoor I2CXL-MaxSonar-WR sensors have a robust PVC housing designed to meet IP67 water intrusion. The sensors provide short to long distance detection and ranging with a narrow beam pattern. The I2CXL-MaxSonar-WR outdoor ultrasonic sensors have high power output, noise rejection, auto calibration, and factory calibrated beam patterns. In addition to the standard I2CXL-MaxSonar-WR, has developed the Fâ??Option for additional protection necessary in a few hazardous chemical environments. Extremely corrosive gases or liquids can degrade or compromise the operation of the sensing unit. As a result, we offer a more chemically inert seal which allows our sensors to operate in all but the harshest of chemical environments. In addition to the chemical resistance the sensor has improved performance in wet or dust environments. MB7040 I2CXL-MaxSonar-WR Ultrasonic Rangefinder Product Specifiations * Resolution of 1 cm * Up to 40Hz reading rate * RoHS Compliant * Operates from 3.0-5.5V * IP67 rated, I2C interface ultrasonic sensor * Maximum range of 765 cm (300 inches) * Operational Temperature from -40'C to +70'C MB7040 I2CXL-MaxSonar-WR Ultrasonic Rangefinder Features and Benefits * Low power consumption * Narrow, controlled beam * Easy to use interface * Detects smaller objects * Can be powered by many different types of power sources MB7040 I2CXL-MaxSonar-WR Ultrasonic Rangefinder Applications and Uses * People detection * Security * Motion detection * Useable with battery power * Autonomous navigation * Educational and hobby robotics * Collision avoidance -
SONIC-ANEMO-MICRO Ultrasonic Wind Speed Sensor Description: As a result of its very special electronic architecture the SONIC-ANEMO-MICRO shows a very low electrical consumption. It is ideal for remote stations or mobile installation. SONIC-ANEMO-MICRO is an OEM sensor designed for integration in other original Equipment. This sensor shows a very low consumption. It operates from 300µA. SONIC-ANEMO-MICRO is the lowest consumption power solution of all LCJ sensors. SONIC-ANEMO-MICRO Ultrasonic Wind Speed Sensor Specification: Output data format: ASCII format, avaibility Information transmited: Instant. W. Speed, Instant. W. Angle, avaibility Output rate: select. 1 meas. and Tx: every 1,6 or 18 s Wind module sensitivity: 0.12 m/s Wind module resolution: 0.05 m/s Wind module dynamic: 0.12 to 40 m/s Direction sensitivity: +/-1.5 degree Direction resolution: 1 degree Power supply: 3 V to 3.6 V DC Electrical consumption: 200µA avg Op. temp. without icing: -15 degree C to +50 degree C Cable: 50 cm / 4x0.22 mm2 Connection: 4 wires Weight of the head: 100 gr Weight of unit assembly: N/A Mounting: N/A
CV7-V Ultrasonic Wind Speed Sensor Description The CV7 is easily integrated into measurement and monitoring systems. The CV7-V is powered by 8-30 VDC power supply and it outputs RS232/RS422 (5V level signal) / NMEA0183. CV7-V Ultrasonic Wind Speed Sensor Application Static wind sensor A conventional wind vane/anemometer features mechanical rotating parts. These moving parts expose the sensor to failure. CV7 series was extensively tested in Marine applications for both precision and robustness. Configurable wind sensor CV7-V can be programmed and configured for : angle correction, smoothing time constant, units of measurement and interface format. CV7-V connexion CV7-V can be used connected to a PC and any systems featuring an NMEA® input port and specific pieces of equipment using conventional formats. In PC mode, this bidirectional sensor can be set up for angle correction, damping, measure units and interface format. Quality All LCJ Capteurs are designed and manufactured in the Nantes region in France where they are fully tested throughout the manufacturing process. CV7-V Ultrasonic Wind Speed Sensor Specification: Output data format: NMEA0183; MWV, XDR Information transmited: Instant. W. Speed, Instant. W. Angle, avaibility Output rate: 2 Hz / 30 Hz measurement Wind module sensitivity: 0.12 m/s Wind module resolution: 0.05 m/s Wind module dynamic: 0.12 to 40 m/s Direction sensitivity: +/-1.5 degree Direction resolution: 1 degree Power supply: 8 V to 30 V DC Electrical consumption: 9 mA Op. temp. without icing: -15 degree C to +55 degree C Cable: 25 m / 4x0.22 mm2 Connection: 4 wires Weight of the head: 100 gr Weight of unit assembly: 200 gr with mounting part Mounting: Vertical ; 300 aluminium arm, 16 mm
