APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Tiles Adhesive (CT-01),(02),(03), Tiles Epoxy Grout, Tiles Grout (Light Color), Tile Grout (Dark Color), Tiles Epoxy Grout Sparkle, Block Jointing Mortar, Wall Putty, Floor Hardener Non-Metallic, Tile Spacer (2mm, 3mm, 4mm,5mm), SBR. Etc. Products are available in stock.
Resin finishing of woven and knitted fabrics composed of cellulosic fibres and their blends with synthetic fibres. For embossed, schreiner and chintz finishes. The finished textile materials have a very low formaldehyde content particularly in the LAW 112 and AATCC 112 test methods meeting the Oeko-Tex standard 100 of 75 ppm free formaldehyde. CD-281 shows good finish effects that have a high stability to hydrolysis, and are also fast to washing at the boil and to dry cleaning.
Superplasticizer based on melamine and Polycarboxylate, of very good quality. Used on mortars and concrete, etc.
YL-SNF-C(Na2SO4 less than 18%) Sodium Naphthalene Sulfonate Formaldehyde This product, named -naphthalene sulfonate formaldehyde condensate, is non-air entraining superplasticizer. It has good dispersing performance to the cement particles. Compared with traditional plasticizer, it has higher water reducing rate, and good for preparing mass concrete, fresh concrete required for early strength and high strength, and precast concrete and parts. It also has good adaptability to commonly used cement, and widely used in roads, bridges, dams, power engineering, civil construction, steam and natural curing precast parts and other projects. Advantage: * Higher water reducing rate. By the recommended dosage, the water reducingrate can reach 15% -20%. * Improve the workability of concrete, such as compression, long-term strength, flowability, etc., and enhance the reinforcement of steel and concrete. * Reduce costs. In the case of maintaining the same workability and strength, cement amountcan be reduced. * Wide adaptability, cost-effective. Good adaptability to all kinds of cement, such as Portland cement, slag cement, volcanic ash cement, etc. * Be mother material to formulate other admixtures.(like early strength, set retarder, pumping agent, antifreezing agent).
Supplying business of construction chemicals like Water proofing coating material for plaster and concrete
YL-PL-WR Polycarboxylate Superplasticizer (Water reducing type, 40-50% solid content) * High water reduction, low dosage. The water reducing rate can reach 20%-40% with recommended dosage. * Early and high strength. The early strengthand 28 day strength have been obviously improved. * Low slump loss: complywith the pumping agent standard, slump loss would besignificantly reduced. * High durability: This product can effectively reduce the W/C ratio, improve durability. * It can be used as a mother liquor to produce other functional admixture, such as early strengthtype, retarder, pumpingconcrete admixture, antifreezer, etc.; * Environmentalfriendly products: the production does not pollute the environment; * Non-corrosionon steelbar.
1. Increasing productivity and improving quality in cement grinding process 2. Saving the production cost and time 3. Anti-coagulation and stable grinding ability 4. Increasing early and long term strength 5. Reduction of CO2 emission and energy cost.
1. Increasing productivity and improving quality in cement grinding process 2. Saving the production cost and time 3. Anti-coagulation and stable grinding ability 4. Increasing early and long term strength 5. Reduction of CO2 emission and energy cost.
Sodium naphthalene sulphonate fdn- 1 used for and widely for self-cured, vaporcured concrete and its formulations. At the early stage of Application, extremely prominent effects are shown. As the result, the modulus and siteutilization Can be drastically, the procedure of vapor cureis omitted in peak-heat summer days. Statistically 40-60 metric tons of coal willbe preserved when a metric ton of the material is consumed. 2 suitable for preparation of early-strength, high-strength, high-anti-filtration and selfsealing& pumpable concrete.
Main performance 1. Can be applied as common water reducing admixture and built material of series multifunction high-performance water reducing admixtures. 2. Can be adopted as the adhesives in the briquetting procedure in the vertical retort zinc smelters. 3. Can be used as embryo reinforcing agents in the fields of pottery and porcelain and refractory materials. They can increase the fluidity of the slurry and thus to improve the strength of the embryo. 4.In the field of water-coal paste, the sodium lignosulphonate series products can be adopted as the main compound materials. 5.In agriculture, the sodium lignosulphonate series products can be applied as the dispersant agents of pesticides and pelleting adhesives of fertilizers and feedstuffs.
Sodium lignosulphonate ( lignosulfonate ) water reducer are mainly for concrete mixture as water-reducing additive. Low dosage , low air content , water reducing rate is high , adapt to most kind of cement. Can confected as concrete early-age strength enhancer , concrete retarder , antifreeze , pumping aids etc. Nearly no precipitate product in the liquor additive which is made from the sodium lignosulphonate and naphthalin-group high-efficiency water reducer .The sodium lignosulphonate is fit for apply to building project, dam project, thruway project etc.
Sodium lignosulphonate used in the field of concrete additives, the sodium lignosulphonate series products can be applied as common water reducing admixture and built material of series multifunction high-performance water reducing admixtures. The products can be directly adopted as additive in the concrete .Moreover, they also can be compounded with such high-performance water reducing admixtures as naphthalene series and melamine series etc. And, they are also ideal materials for series retarding agents and pumping agents etc.
Sodium gluconate uses 1.It can be used as food additives. 2.It can be used as water quality stabilizer because it has excellent inhibiting capacity to scale. 3.It can beused as surface cleaning agent of metal 4.It can beused as cleaning agent of glass bottle 5.It also can be used as water reducing agent and retarder in the building & construction industry.
Sodium lignosulphonate in ceramic for ceramic products, can reduce the carbon content to increase green strength and reduce the amount of plastic clay, mud flows and good to improve the yield 70-90%, sintering speed reduction from 70 minutes to 40 minutes. 3. The sodium lignosulphonate series products can be adopted as the adhesives in the briquetting procedure in the vertical retort zinc smelters. 4. The sodium lignosulphonate series products can be used as embryo reinforcing agents in the fields of pottery and porcelain and refractory materials. They can increase the fluidity of the slurry and thus to improve the strength of the embryo.
ICG-1000 is various types of grinding aids are available to meet customer's needs for saving, cost , increasing productivity and improving quality in cement grinding.
Specification Markclinker Standardbritish standards gb175-1999 Originchina Deliverycif aswp Packingbulk or 50 kg bags Inspectionsgs or similar Clinker: chemical composition Sio220-22.5üô Al2o34.6-7e2o33-5 üô Cao64% min Mgo 4% max So3 1% max Loss of ignition1% max Insoluble residue0.5% max F-cao1.5% max Total alkali0.9üô max C3s50-60üô C2s15-23üô C3a6-11üô C4af7-15üô Clinker: physical and mechanical properties Compressive strength @ 03 day's 28 mpa min @ 28 day's 55 mpa min Payment for clinkerlc - letter of credit via Prime Bank Bg-100% - bank guarantee Conditional swift against documents Ffdlc Rdlc Cash t/t Standard (50kg/small woven
Hardner Hardner : specially formulated for precast industries (paver blocks & precast cement articles).Fxt hardner is a colourless viscous water soluble liquid to be added in concrete mix for casting precast articles. Special features: Water white: it is colour less hence does not hinder the colours used in manufacturing of precast articles & white cement. Packing: 5, 50 & 250 kgs in hmhdep drums Packing: 5, 50 & 250 kgs in hmhdep drums
Coverage: 3.5 to 5 m²/kg depends on concrete Specific gravity at 30°c :- 1.75 Application temperature :- 5 °c to 45°c Drying time :- approx 2 hrs at 30°c 250ltr
