Specifications1.broad application2.10 years experiences in research3.professional manufacturer4.famous brand
Model ,Host Power KW,Annual Capacity,Host Volume M3,Floor Space m2
LJWZ--05,7.5,0.54-1.8,0.5,20-100
LJWZ-10,11,1.08-3.6,1.0,20-100
LJWZ-20,18.5,2.16-7.2,2,20-100
LJWZ-25,19,2.7-9.0,2.5,20-100
LJWZ-30,22,3.24-10.8,3,20-100
normal
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Zmft series full automatic dry mixed mortar production line is based on the latest design concept in europe, this production adopts the advanced computer auto-control system, whose production capacity can reach 30-100 thousand tons per year depend on the system configuration. The production line consists of storage system, metering and batching system, conveying system, mixing system, air compressor system , packaging system, and dedusting system, etc According to requirements of the customers, the system can be equipped with 3-6 bulk storage bins, the material in which will, after being processed by the metering and batching system, be conveyed to pending-for-mixing bin, and then fed into the high-efficiency biaxial agravic mixer for continuous mixing. The finished product in conformity with mixing accuracy requirements can be sent to the finished products bin shortly after mixed. Moreover, there is design with automatic rationing and packaging machine at the bottom of finished products bin, allowing for synchronous auto-packaging operation. Featured with easy and convenient operation, high efficiency, it can both obviously reduce labor intensity and effectively reduce dust pollution. Wooden package
scription of mortar production line: I. This line has simple structure ,flexible production process and low cost.Equipments on this line are easily repaired and replaced. II. The raw materials for mortar are mainly sand,cement,flyash and limestone.They are very cheap, thus,give more additive value to mortar.Over all,this line is of high profit and is the best choice for investors. Models of mortar production line: Type Model Mixer/KW Capacity T/Need area/m*m FRQ: 1.How many kinds of mortar can this line produce? A: There are more than 16 kinds of mortar and this line can produce about five of them. If you want to produce even more,we can also offer. 2.How many person needed in this line? A: 3-5 workers will be enough to operate this line. 3.Is the line full-automatic? A: Yes,we can custom as your need. 4.Whats the difference between full-automatic line and semi-automatic line? A:(1)Sem-automatic line need manual help to upload materials,while full-automatic line need not. (2)semi-automatic line may not need material silos,full-automatic line need. (3)Semi-automatic line is relatively cheaper than full-automatic line. 5. Is it including packing machine? A: Yes. 6. How many types of mortar production line is there? What¡¯s the difference? A:(1)Normally,three. Vertical type ,block type and workshop type. (2)Normally: vertical type:the height of this line is big more investment of steel supporting structure Block type: more factory area less steel supporting structure Workshop type: install in a workshop and the height should be low 7.What is factory area needed?. A: It depends on the line type. 20-200m*m will be enough 8.Is it only dry or can make wet also? A:This line is most suitable for dry mortar and can mix wet mortar with 16% moisture. 9.What¡¯s the total power consumption (KW)? A:It is about 50KW. It is widely depends on the capacity and number of raw materials. 10 What¡¯t the capacity of the line? A:2-50ton per hour. 11.What¡¯s the guarantee period? A:12 months. With in this 12 months we take care of all the problems occurred, after that we offer repair and maintain service. 12.Can you install in my country? A:Yes, we offer oversea installation service. 13:Can you teach us how to operate this line? A:Yes.We offer training service free of charge. 14:What¡¯s the delivery date? A:30 days. 15: Whats the payment term? A:TT and L/C. 16.Can you delivery to my port? A:Yes,no problem. 17:How can I inspect the line before shipment? A:You can inspect by yourself or you fine someone inspect for you. Materials for mortar: 1.Cementing material: cement, lime, plaster. 2.Aggregate: yellow sand, quartz sand, limestone, dolomite, expanded perlite. 3.Mineral admixture: industrial byproduct, industrial slag, fly ash, pozzolana, fine silica powder etc. 4.Water-retention and thickening material. 5.Chemical additives. Production process: 1.Raw material storage 2.Raw material convey and weigh 3.Addition and weighing of additive 4.materials mixing 5.finished mortar storage and packing 6.Other device: dust collection system+air compressor system+PLC electric controlling system+steel supporting system Wood case
Dry-mixed mortar tower type production line H-tec dry-mixed mortar tower type production line can produce the below product¦ 1adhesive mortar¦such as ceramic tile adhesive, filler, heat preservation multiplexed system use adhesive mortar, etc. 2rendering mortar¦such as internal and external rendering mortar, lacquer putty, colored decoration mortar, heat preservation mortar, etc. 3masonry mortar ¦such as normal masonry mortar, concrete masonry mortar, heat preservation, masonrymortar, etc. 4floorscreed mortar ¦such as normal floorscreed mortar, self-leveling mortar, etc. 5special mortar ¦such as mending mortar, waterproof mortar, floor hardener, etc.
Thermotax is a ready to use air setting refractory mortar. It is air setting mortar having good strength on air drying, forming strong joints & conferring an almost monolithic structure to the fire brick work. Moreover, it is highly suitable for Insulation brick lining work as well as refractory Brick lining work.
Refractory Mortar are heat resistance binding materials which are used in binding Refractory brick lining. Monolithic refractories include refractory castable, refractory mortar, spray mass etc. We offer two types of refractory mortar according to its application including Heat setting mortar : IS-6 Mortar, IS-8 Mortar, 40% To 90% Mortar Air setting Mortar : Set-50 Mortar, Set 50F Mortar
25/50 Kg BAG & 01 Ton Jumbo bag Refractor Castable are heat resistance binding materials which are used in binding Refractory brick lining. Monolithic refractories include refractory castable, refractory mortar, spray mass etc. We offer wide range of refractory castable such as : Conventional Castable Super Castable, Fire crete, HEAT - A Castable, HEAT- K Castable Low & Ultra Low cement Castable MON -45, MON-60, MON-70, MON-80, MON-90 Gunning Castable MONGUN-45, MONGUN-60, MONGUN-70 Insulating Castable INSUCAT-9, INSUCAT-11, INSUCAST-13, INSUCAST-15
Acid Resistance Mortar are used for Lining of Acid Resistance Bricks which are chemically resistant and thermally durable. These are used for masonry construction and flooring which is prone to chemical attack. Types of Acid Resistance Mortar: Silicate Mortar Resin Mortar Sulphur Mortar
