Automated dry mix mortar production line consists of sand drying system, raw material storage silo, aggregate and additive weighing system, mixing main machine, automatic packaging system and centralized control cabinet. Production from 5-10 t/h to 50t/h.
Main Features
1. It features magnificent appearance, good quality, high productivity and accurate mortar proportioning.
2. The dry mix mortar production line uses a centralized control system, making the equipment easy to operate.
3.According to the layout type, it can be classified into tower type, self tower type and series type. Its up to the customers workshop area. The needed area is 500~5000m2.
4. We can provide one-stop service from design to installation according to our customers' specific requirement.
china coal0001 1866076028PZ-7B Explosion Proof Dry-Mix Mortar Spray Machine Introduction of PZ-7B Explosion Proof Dry-Mix Mortar Spray Machine PZ-7B Explosion Proof Dry-Mix Mortar Spray Machine is a dry concrete shotcrete machine. This kind shotcrete machine uses the compressed air to convey or high-speed jet concrete mix with a certain proportion to the surface through the pipelines. The concrete mix on the surface set and harden to form concrete support layer. In recent years, shotcrete technology with a simple process, an unique effect, the economic cost and fast construction speed, is widely used in construction, rail and road tunnel construction, mine development, slope reinforcement and other fields. Parameter of PZ-7B Explosion Proof Dry-Mix Mortar Spray Machine Item PZ-7B Output 7m3/h Max. convey dist Horizontal:200m Vertical: 20m Water cement ratio ?¤0.4 Max. Aggregate. size 20mm Hose inner size 64mm Operating air pressure 0.4~0.6MPa Air consumption 8-10 m3/min Rotor  diameter 480mm Motor power Y160m-6-7.5KW Voltages 380v or as your requirement Overall dimension(mm) 1600X700X1150 Whole weight 900kgs
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Specifications1.broad application2.10 years experiences in research3.professional manufacturer4.famous brand Model ,Host Power KW,Annual Capacity,Host Volume M3,Floor Space m2 LJWZ--05,7.5,0.54-1.8,0.5,20-100 LJWZ-10,11,1.08-3.6,1.0,20-100 LJWZ-20,18.5,2.16-7.2,2,20-100 LJWZ-25,19,2.7-9.0,2.5,20-100 LJWZ-30,22,3.24-10.8,3,20-100 normal
Dry Mortar Transport Pump: Qz-hb-40s dry powder mortar transport pump.The main function of qz-hb-40s dry powder mortar transport pump is to send mortar pump to the working surface, which is the precondition for the grouting work of qz-hb-2q mortar spraying machine. Qz-hb-40s dry powder mortar transport pump can be used in construction, railway and road tunnels, bridge culverts, hydropower, mining and national defense projects.
Thermotax is a ready to use air setting refractory mortar. It is air setting mortar having good strength on air drying, forming strong joints & conferring an almost monolithic structure to the fire brick work. Moreover, it is highly suitable for Insulation brick lining work as well as refractory Brick lining work.
Supplier: Dry-mixed mortar production line, dry mixed mortar packing machine, cement and concrete mixing station.
Zmft series full automatic dry mixed mortar production line is based on the latest design concept in europe, this production adopts the advanced computer auto-control system, whose production capacity can reach 30-100 thousand tons per year depend on the system configuration. The production line consists of storage system, metering and batching system, conveying system, mixing system, air compressor system , packaging system, and dedusting system, etc According to requirements of the customers, the system can be equipped with 3-6 bulk storage bins, the material in which will, after being processed by the metering and batching system, be conveyed to pending-for-mixing bin, and then fed into the high-efficiency biaxial agravic mixer for continuous mixing. The finished product in conformity with mixing accuracy requirements can be sent to the finished products bin shortly after mixed. Moreover, there is design with automatic rationing and packaging machine at the bottom of finished products bin, allowing for synchronous auto-packaging operation. Featured with easy and convenient operation, high efficiency, it can both obviously reduce labor intensity and effectively reduce dust pollution. Wooden package
We are a renowned and customer centric firm, which is engaged in delivering a comprehensive range of Dry Mortar Machinery. Features: Almost nil wastage of the material at site High performance Inventory cost saving No multiple raw materials As it is customized product costing will be varied according to plant capacity and catagory. Request Callback Additional Information: Item Code: MDMM Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer) Port of Dispatch: Pune Production Capacity: 2 TPH - 5 TPH Delivery Time: 3-4 weeks Packaging Details: As per scope
