DESCRIPTION:
Stop Leak is a liquid admixture when mixed with portland cement becomes an extremely rapid setting plastic material used to stop pressure leaks in concrete and masonry structures.
USES:
Stop Leak can be used to stop water leaks in dams, foundation walls, manholes, pipelines, underground structures, swimming pools, foundtains, tunnels, basement walls and floors.
ADVANTAGES:
Will stop water under pressure.
ECONOMICAL:
Sets within 60 to 90 seconds, generates minimal heat when setting
Becomes extremely plastic when combined with portland cement
Stop Leak liquid must be stored at temperatures above freezing.
MIXING RATIO:
1Kg Stop Leak : 2,8 kgs cement (2,2 pounds Stop Leak : 6,17 pounds cement)
LIMITATIONS:
Judgment must be used to mix Stop Leak in small quantities due tu the extremely rapid set. After the portland cement is added to the liquid Stop Leak, the mixed compound will set in approximately 60 seconds. This action allows the material to bond mechanically and chemically to saturated surfaces. A delay in setting, if required, can be attained by adding fine sand to the neat cement mixture or by reducing the amount of cement added to the liquid.
Safe
- Odorless, non-toxic, does not affect the health of users and the environment
- Should wear gloves and necessary protective equipment when using
- If splashed into eyes, use clean water or eye drops to wash several times
Storage conditions
Product must be stored in original unopened and undamaged sealed packging in dry conditions.
Colour: Clear liquid
Shelf life
12 months from the production date
Packaging
- Stop Leak 0,5Kg (1,1Pounds)
- Stop Leak 2,5Kg (5,51Pounds)
- Stop Leak 6,5Kg (14,3Pounds)
Description: VCOLD is a rapid-setting structural repair mortar. It is designed primarily for the durable repair of concrete. Utilising all the latest technology this Portland cement-based and fibre-reinforced product is extremely strong and hard wearing. This makes it ideal for roads, runways, bridges, decks, floors and footpaths. Requiring only the addition of water, this single component mortar is rapid curing. VCOLD quick set mortar is physically and chemically compatible with the host concrete. This means it is quick to exhibit a high adhesive and compressive strength. Product name: VCOLD Compressive strength - 35 Mpa, in 6 hours - 50 Mpa, in 1 day - 80 Mpa, in 1 week Application temperature - In cold temperatures, tepid water may be used to adjust working life - In 20-40 temperatures, cold water should be used to adjust working life Mixing ratio: - 25kgs powder: 3,7L water - 5kgs powder: 0.7L water Uses of VCOLD VCOLD is used on floors that are subjected to heavy wear such as: - Roads - Runways - Bridges - Decks - Floors - Footpaths The repair mortar can be used as supplied up to 100mm deep. It can also be bulked out with clean, washed, sharp sand to form a high performance screed or for floor or deck repairs up to maximum depth of 300mm. One barrel 25kgs of VCOLD produces 13 litres Applying VCOLD Rapid Set Repair Mortar: VCOLD should only be installed by those experienced in structural waterproofing. Please follow manufacturerâ??s instructions for full details across the range of applications. Preparation â?? Start by mechanically removing all damaged concrete back to a sound core. Ideally you want to expose the steel reinforcement to at least 25mm behind the bars and 50mm beyond the point at which corrosion is visible. The perimeter of the repair area should be stepped to a depth of 10m using a saw, disc cutting or preferably a power chisel. Make sure that all areas to be repaired are free from dust, oil, grease, corrosion by-products and all organic growth. Any smooth surfaces should be roughened with any surface laitance removed. You should now thoroughly soak the prepared surface with clean water until uniformly saturated. Ensure there is no standing water. Mixing: Mechanically mix VCOLD using a forced action pan mixer or in barrel using a drill and paddle. Normal applications = typically use 3,7 litres of clean water per 25kgs barrel Normal applications = typically use 0.7 litres of clean water per 5kgs barrel Note: - In cold temperatures, tepid water may be used to adjust working life - In 25-40 temperatures, cold water should be used to adjust working life Important Note: The product cannot be mixed using a normal concrete mixer. Pot life is about 10 minutes, depending on the temperature and humidity. For screeding applications or deep repairs consult technical sheets.
Description: Fairing Coat Mortar: is one component, polymer modified, cementitous mortar based containing silica fume. Product name: Fairing Coat Mortar Compressive Strength: â?¥ 20 Mpa (1 day) â?¥ 50 Mpa (28 days) Mixing ratio: - Approx. 5.5 L of clean water per 25 kgs barrel - Approx. 1.1 L of clean water per 5 kgs barrel Layer Thickness: Max. 5mm Pot Life ~ 30 min. (at 27�ºC / 65% r.h) Usage: Fairing Coat Motar: is used as repair mortar for minor surface defects on: - Concrete - Mortar - Stone Fairing Coat Mortar: is a cosmetic mortar designed to eliminate surface defects due to demoulding, pores or honeycombs, and is suitable forsmall repairs on: - Precast concrete elements - Fair-face concrete - Columns and beams - As levelling mortar and fairing coat or finishing skim coat to concrete, mortar patches and screeds. Advantages: - Ready to use requiring only the addition of water - Excellent workability - Rapid strength development - Good mechanical strength - Good adhesion to substrate - No corrosive effect on reinforcement steel - Non-toxic Packaging: Barrel 5kgs and Barrel 25kgs Colour: Powder / Grey Shelf life: 9 months if stored properly in unopened, original packaging. Storage conditions: Dry, cool, shaded place Mixing ratio: Water : (Fairing Coat Mortar) powder = 1:4.0 (parts by weight) Approx. 5.5 L of clean water per 25kgs barrel. Approx. 1.1 L of clean water per 5kgs barrel. Layer Thickness: Max. 5mm Pot Life: ~ 30 min. (at 27�ºC / 65% r.h) Fairing Coat Mortar: should be mechaically mixed in a clean container using a low-speed electric mixer (max. 500 rpm). A minimum mixing time of 3 minutes is recommended to throughly blends the components. Fairing Coat Mortar: can be applied by spatula or trowel. Work the mixed mortar well into the substrate. Force material against the edge of the repair, working towards the center. Curing treatment: To achieve the full potential of any cement based material, curing is essential. In warm or windy weather, the use of standard curing methods are necessary (use of polyethylene sheets or damp hessian) to prevent premature drying out of mortar. Cleaning of tools: Remove non-hardened Products from tools and requipment with water. Hardened material can only be remove mechanically.
Description: VFLOOR1 is a single component Cementitious Self Leveling Mortar. Once cured, it provides a smooth, level surface on which to install a variety of floor coverings. Suitable for prepairing interior floors prior to laying parquet, vinyl sheet and tile, soft floor covering, natural stone, ceramic tiles, etcâ?¦ It can be used on a wide range of absorbent and non-absorbent floor surfaces including concrete, cement and sand screeds, terrazzo, asphalt, ceramic & quarry tiles. Layer-thickness 2-10mm Can be pumped Standard primers give excellent bonding to the VFLOOR1 products Product name VFLOOR1 Compressive strength >40 Mpa, 28 days later Flexural strength >8 Mpa, 28 days later Application temperature 5-30 degree Mixing ratio 20kgs powder + 5.2kgs Liquid Product name PRIMER Mixing ratio 2kgs Primer + 2L water + 4kgs cement Feature & Benefits: - Single component, just mix with water - Good adhesion to primed substrates - Good flow, self smoothing - Rapid setting and early strength - Easy and quick to lay Mixing: Add clean water to suitable mixing bucket. Mix slowly and continuously to form a homogeneous mixture. - VFLOOR1 20kgs barrel required approximately 5.2 litres of clean water The mixed materials is immediately ready to use and should be used within 30-40 minutes after mixing. Ready for foot traffic after approx. 3 hours. Drying time: Prevent draughts across the floor to avoid localized premature drying At ambient temperature, VFLOOR1 will appear to be dry after approximately 24 hours. Floor laying may commence after 48 hours. Coverage: - At an application thickness of 2mm the coverage will be approx. 5kgs per 1m2 Shelf Life: 9 months.
Supplier: Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
VN SEAL 109 is a liquid applied, crack bridging 2 pack acrylic polymer modified cementitious waterproofing coating system with moderate to high degree of elasticity depending on system buildup Advantages - Crack-bridging & Elastic - Good Impermeability against water ingress - Highly water resistant, arrest salt petre and prevent carbonation - Extremely good bonding with high abrasion resistance - Simple application and fast curing - It has excellent adhesion to concrete, brickwork and corrugated asbestos cement sheets Appication - Used as a seamless, impervious coating on flat roof for both exposed and concealed waterproof coating system - Basements - Water retaining structures - Underground concrete structures, pits, basins, sumps etc. - Used as waterproofing coating on concrete, screed, mortar, brick tiles, cement tiles, plaster or porous stone substrates Packaging 1) Part (A+B) : 28 kg ready to mix units x 2 sets Part A is grey power: 20kg/Barrel Part B is white milky liquid: 8kg/Barrel 2) Part (A+B) : 14 kg ready to mix units x 2 sets Part A is grey power: 10kg/Barrel Part B is white milky liquid: 4kg/Barrel Shelf life 12 months from the production date Storage conditions Keep in cool and dry places
VNSEAL 104W is a two component, white colour, flexible cementitious waterproofing membrane consisting of a synthetic resin mixed with a blend of selected cement and well-graded fillers. When mixed, VNSEAL 104W becomes a smoooth slurry and is easily applied by brush, roller or suitable spraying equipment. VNSEAL 104W can be applied onto damp substrates. The cured membrane is flexible, durable and weather resistant and has excellent adhesion to most building substrates. Its unique chemical structure provides a breathable membrane that is permeable to water vapour and yet impermeable to water. VNSEAL 104W is capable of bridging hairline cracks. Typical Uses: Waterproofing of Basement walls and lift pits Waterproofing of potable water tanks, waterproofing of reservoirs, culverts, storm drains, canal, water retaining and water excluding structures. Waterproofing of kitchens and toilets Waterproofing of balconies and planter boxes Waterproofing of swimming pools and water features Waterproofing to precast gable end walls Waterproofing to RC flat roof (re-roofing-exposed and concealed applications) and gutters. Waterproofing to external wall prior to installation of claddings. Advantages: Pre-packed Easy to mix and apply Excellent waterproofing qualities â?? able to withstand high hydrostatic pressure Excellent adhesion to concrete, masonry, ceramics, natural and artificial Flexible able to bridge hairline cracks up to 2mm Does not contain chloride or other corrosive salts which cause efflorescence Non toxic- suitable for use in waterproofing of potable water tanks Able to withstand light foot tracfficking Can be applied onto damp substrates Weathering resistant Mixing Instructions: Pour Part A (liquid) into Part B (White powder)container and mix with a slow speed mechanical mixer until homogenous and lump free. Allow the mix to stand for 5 minutes and re-stir manually before use. Application: For horizontal and vertical surfaces, a roller, brush or spray gun, may be used to apply the slurry. Care must be taken to ensure that air is not entrapped in the membrane Apply the first coat of VNSEAL 104W and allow it to dry. At the same time, ensure that all joints and corners are properly coated, preferable with a brush. Allow membrane to dry for approximately 2 hours before application of the second coat VNSEAL 104W the professionals choice of quality products and system for building construction Shelf life Expiry date 12 months from the production date Storage conditions Dry, cool, shaded place Packaging 1) Combo A: 4kg - B: 2kg Component A is White powder: 4kg/barrel Component B is milky white liquid: 2kg/plastic can 2) Combo A: 10kg - B: 5kg Component A is White powder: 10kg/barrel Component B is milky white liquid: 5kg/plastic can 3) Combo A: 20kg - B: 10kg Component A is White powder: 20kg/barrel Component B is milky white liquid: 10kg/plastic can
VNSEAL 104 is a two component, flexible cementitious waterproofing membrane consisting of a synthetic resin mixed with a blend of selected cement and well-graded fillers. When mixed, VNSEAL 104 becomes a smoooth slurry and is easily applied by brush, roller or suitable spraying equipment. VNSEAL 104 can be applied onto damp substrates. The cured membrane is flexible, durable and weather resistant and has excellent adhesion to most building substrates. Its unique chemical structure provides a breathable membrane that is permeable to water vapour and yet impermeable to water. VNSEAL 104 is capable of bridging hairline cracks. Typical Uses: Waterproofing of Basement walls and lift pits Waterproofing of potable water tanks, waterproofing of reservoirs, culverts, storm drains, canal, water retaining and water excluding structures. Waterproofing of kitchens and toilets Waterproofing of balconies and planter boxes Waterproofing of swimming pools and water features Waterproofing to precast gable end walls Waterproofing to RC flat roof (re-roofing-exposed and concealed applications) and gutters. Waterproofing to external wall prior to installation of claddings. Advantages: Pre-packed Easy to mix and apply Excellent waterproofing qualities able to withstand high hydrostatic pressure Excellent adhesion to concrete, masonry, ceramics, natural and artificial Flexible able to bridge hairline cracks up to 2mm Does not contain chloride or other corrosive salts which cause efflorescence Non toxic- suitable for use in waterproofing of potable water tanks Able to withstand light foot tracfficking â?¢ Can be applied onto damp substrates â?¢ Weathering resistant Mixing Instructions: Pour Part A (liquid) into Part B (powder)container and mix with a slow speed mechanical mixer until homogenous and lump free. Allow the mix to stand for 5 minutes and re-stir manually before use. Application: For horizontal and vertical surfaces, a roller, brush or spray gun, may be used to apply the slurry. Care must be taken to ensure that air is not entrapped in the membrane Apply the first coat of VNSEAL 104 and allow it to dry. At the same time, ensure that all joints and corners are properly coated, preferable with a brush. Allow membrane to dry for approximately 2 hours before application of the second coat VNSEAL 104 the professionals choice of quality products and system for building construction Shelf life Expiry date 12 months from the production date Storage conditions Dry, cool, shaded place Packaging 1) Combo A: 4kg - B: 3kg Component A is Grey powder: 4kg/barrel component B is milky white liquid: 3kg/plastic can 2) Combo A: 10kg - B: 7,5kg Component A is Grey powder: 10kg/barrel component B is milky white liquid: 7,5kg/plastic can 3) Combo A: 20kg - B: 15kg Component A is Grey powder: 20kg/barrel component B is milky white liquid: 15kg/plastic can
Description: BOT is a one part, pre-blended, (coloured) mineral dry shake hardener for concrete comprising of cement, specially selected quartz mineral aggregates and admixtures BOT is one of the most effective ways to protect the surface and extend the life of the floor BOT may only be used by experienced professionals. BOT provides a hard wearing, mineral dry shake topping for monolithic floors. When sprinkled and trowelled into fresh wet concrete floors, it forms a wear resistant smooth surface. Typical uses are in warehouses, factories, shopping malls, public areas, where wear durable and wear resistant floor is the key requirement. Applications: - Airplane hangars - Electronic assembly plants - Manufacturing plants - Warehouses and distribution centers - Shipping and receiving areas - Maintenance facilities - Commercial and industrial floors subject to deicing salts - Where light-reflective flooring is desired - Floors subject to heavy or frequent traffic - Salt-storage facilities - Multi-purpose sporting facilities - Recreational facilities Converage: - Moderate duty 7-9 kg/m2 - Heavy duty 9-12 kg/m2 - Concentrated traffic 12-15 kg/m2 - Extra heavy duty +15 kg/m2 Advantages: - Prevents concrete damage due to abrasion, impact, punching, and scraping - Decline cost of maintenance during the life span of the floor. - Enhances the appearance of floor surface. - It adds texture and slip resistance - It is able to increase the value of an industrial building and improve building sale-ability - Dry shake is an economical way to add color which is not fade with time - It can help the floor to reflect more light, reducing lighting and energy requirements. Extended floor life Packaging: 25kgs barrel Colour: Grey and Green Shelf Life: 9 months
