Airbus Standard:ABD 0031 Fire Test to Aircraft Material (Copper clad laminate)
1.ABD 0031 Airbus Fire Test to Demonstrated that
Acceptable control of the risk of ignition has been achieved
Acceptable control of the rate of and total emission of heat, smoke and toxic fume has been achieved for all major usage materials and surfaces when exposed to a source of ignition.
Acceptable resistance to fire has been achieved for all materials and items required to perform as a barrier to fire or which are required to perform some function when exposed to fire.
2.ABD 0031 Fire Test to Aircraft Material-Product Scope
Rubber Product, Rubber Seal
Plastic Product
Fire Coating
Fire Adhesive
Cable and Wire
Textile (Curtain, carpet)
3.Airbus Standard: ABD 0031 - Fire test to Aircraft Material
Vertical Flammability Test: ABD 0031- 7.1.2 (AITM 2.0002 B/A)
Smoke Density Test: ABD 0031- 7.3.1 (AITM 2.0007)
Smoke Toxicity Test: ABD 0031- 7.4 (AITM 3.0005)
Heat Release Test: ABD 0031 (AITM 2.0006)
Horizontal Test: ABD 0031- 7.1.3 / -7.1.4 (AITM 2.0003)
45�° flammability test: ABD 0031- 7.1.5
4.Far 25.853 Fire test to aircraft material- Test method
Vertical flammability test: 14 FAR 25.853 b(4)),
Smoke Density Test: 14 FAR 25.853 (d), (App. F to part 25, part V)
Heat Release Test: 14 FAR 25.853 (d), Appendix F, Part IV
Seat Test: 14 FAR 25.853 (c, App.F to part II)
Horizontal Test: 14 FAR 25.853 b(2,3), (App. F to part 25 part I (a),(1)
45 flammability test: 14 FAR 25.853 (b), (App. F to part 25, part I (6))
have rich experience to provide BSS 7239 Toxicity Test to Aircraft Material
BSS 7239 Toxicity Test to Aircraft material
BSS 7239: Test method for toxic gas generation by materials on combustion
BSS 7239 Toxicity Test to Aircraft material - Brief
Gases produced for analysis are generated in a specified, calibrated smoke chamber during standard rate of smoke generation testing (ASTM E 662), in both flaming combustion and non-flaming pyrolytic decomposition test modes
BSS 7239 Toxicity Test to Aircraft material- Gases measured
The following gases are required to be measured by this test standard
CO Carbon monoxide
HF Hydrogen Fluoride
HCl Hydrogen chloride
NOx Nitrogen oxides (Both NO, nitric oxide, and NO2, Nitrogen dioxide, are detected)
SO2 Sulfur dioxide
HCN Hydrogen cyanide
Fire test to aircraft material relative standards
FAR 25.853 flammability test to aircraft material
Air bus standard ABD 0031 - airbus fire testing flame, smoke and toxicity
Boeing Standard BSS 7238 fire testing to smoke density
Boeing Standard BSS 7239 fire testing to toxicity
ASTM Standard ASTM E 662 fire testing to Smoke Density
ASTM Standard ASTM E 162 Surface Flammability of materials
GB 8410(Chinese Standard) Flammability Test to Motor Vehicle
CASfire Technical Co.,Ltd have rich experience to provide GB8 410 Flammability of automotive interior materials.
GB8410 Scope
This Standard specifies the technical requirements and test methods for the horizontal flammability of automotive interior materials.
This Standard applies to the assessment of automotive interior materials.
As automotive interior parts (positions, layout and application conditions of the parts, ignition sources, etc.) differ considerably from the test conditions specified in this Standard, this Standard does not apply to the assessment of all the actual flammability of automotive interior materials.
GB8410 Technical requirements
The flammability of interior materials must meet the following technical requirement:
The burning rate is not greater than 100 mm/min.
GB 8410 Test method
Fit the sample horizontally on a U-shaped support then ignite the free end of the sample on a flame of the specified height in the combustion box. 15 seconds later, determine whether the flame on the sample goes out or at what time it goes out, the burnt distance of the sample, and the time used in burning this distance.
GB 8410 - Relative Standard
FMVSS 302 Flammability of Interior materials
SAE J369: Flammability of Polymeric Interior Materials Horizontal Test Method
TL1010: Flammability
ISO 3795:Road vehicles, and tractors and machinery for agriculture and forestry -- Determination of burning behaviour of interior materials
DIN 75200:Determination of burning behaviour of interior materials in motor vehicles
95/28/EC: The burning behaviour of materials used in the interior construction of certain categories of motor vehiclesâ??, and is intended to ensure that they meet fire safety standards
NF P 92-505: Safety against fire - Building materials - Reaction to fire tests - Test used for thermal melting materials - Dripping test.
U.T.A.C 18-502 T1: burning behaviour of materials used in the interior construction of certain categories of motor vehicles
BMW N 60121.0: BMW standard
DBL 5307: Benz Standard
GM L-T06-302G-79: GE Standard
Mitsubishi ES-X60410: Oxygen Index
VW TL 1010: burning behaviour
Volvo STD 5031: burning behaviour
NFPA 130 Standard for fixed guideway transit and passenger rail systems
Standard Introduction
This standard shall cover fire protection requirements for underground, surface, and elevated fixed guideway transit and passenger rail systems, including trainways, vehicles, and vehicle maintenance and storage areas, and for life safety from fire in fixed guideway transit and passenger rail system stations, trainways, vehicles, and outdoor vehicle maintenance and storage areas.
Test Method
Surface Material : ASTM E162 Surface Flammability & ASTM E662 Smoke Density
Elastomers : ASTM C 1166 & ASTM E 662
Fabrics : 14 CFR 25 & ASTM E 662
Cushioning : ASTM D 3675 & STM E 662
Small Compoment : ASTM E 1354 Heat Release
Reference Standards
ASTM E 162 Surface Flammability of Materials Using a Radiant Heat Energy Source
ASTM E 662 Specific Optical Densityof Smoke Generated by Solid Materials
ASTM C 1166 Flame Propagation of Dense and Cellular Elastometric Gaskets
ASTM D 3675 Surface Flammability of Flexible Cellular Materials
ASTM E 1354 Test Method for Heat and Visible Smoke Release Rates
Bombardier SMP800-C Toxic Gas Generation Test
We also can provide the following service of fire test to Railway
EN45545-2 Fire protection of railway vehicles: Requirement for fire behaviors of materials EN45545-3 Fire resistance requirements for fire barriers
NFPA 130 Standard for fixed guideway transit and passenger rail systems
DIN5510-2 Fire behaviour of materials and parts, classification, requirement and test methods
BS6853 Code of practice for fire precautions in the design and construction of passenger carrying trains
NF F16-101 Railway Rolling Stock Fire Behavior Choice of Material
EN 45545-2 New Fire test to railway vehicles -Standard Brief
EN45545 This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by March 2016.
EN 45545 supersedes BS 6853, DIN5510-2,NFF16-101 national standards.
This European Standard exists in three official versions (English, French, German).
EN 45545-2 New Fire test to railway vehicles - European Standard
EN 45545-2:2013+A1:2015: Fire protection of railway vehicles - Part 2: Requirement for fire behaviors of materials and components
EN 45545-2 New Fire test to railway vehicles-Scope
This part of EN 45545 specifies the reaction to fire performance requirements for materials and products used on railway vehicles as defined in EN 45545-1.
For each hazard level, this part specifies the test methods, test conditions and reaction to fire performance requirements.It is not within the scope of this European Standard to describe measures that ensure the preservation of the vehicles in the event of o fire.
EN 45545-2:2013+A1:2015 Fire Test to railway components -Hazard levels
HL1, HL2, HL3
EN 45545-2 New Fire test to railway vehicles -Test Method
EN 45545-2 R1: Surface Products
EN 45545-2 R10: Flooring Covering
EN 45545-2 R15, R16: Wire & Cable
EN 45545-2 R22/ R23: Interior seals, Electrical Equipment
EN 45545-2 R24 : Electrotechnical products
EN 45545-2 R24/R25 : PCB Printed circuit boards
EN 45545-2 R26 : Small electrotechnical products
EN 45545-2:2013+A1:2015: Fire protection of railway vehicles - Part 2: Requirement for fire behaviors of materials and components
This part of EN 45545 specifies the reaction to fire performance requirements for materials and products used on railway vehicles as defined in EN 45545-1.
For each hazard level, this part specifies the test methods, test conditions and reaction to fire performance requirements.It is not within the scope of this European Standard to describe measures that ensure the preservation of the vehicles in the event of o fire.
Hazard levels
HL1, HL2, HL3
Test Method
EN 45545-2 R1: Surface Products
EN 45545-2 R10: Flooring Covering
EN 45545-2 R15, R16: Wire & Cable
EN 45545-2 R22/ R23: Interior seals, Electrical Equipment
EN 45545-2 R24 : Electrotechnical products
EN 45545-2 R24/R25 : PCB Printed circuit boards
EN 45545-2 R26 : Small electrotechnical products
We also can provide the following service of fire test to Railway
EN45545-2 Fire protection of railway vehicles: Requirement for fire behaviors of materials EN45545-3 Fire resistance requirements for fire barriers
NFPA 130 Standard for fixed guideway transit and passenger rail systems
DIN5510-2 Fire behaviour of materials and parts, classification, requirement
BS6853 Code of practice for fire precautions in the design and construction
NF F16-101 Railway Rolling Stock Fire Behavior Choice of Material
CASfire Technical Co.,Ltd
8F Building 4, Chinese Academy of Science,
No.255 South Duiying Road,Jimei, Xiamen 361021, China
Tel: (+86) 0592-3500085
MP: (+86) 18906059211
Email: info@casfire.cn
Website: http://www.casfire.cn
EN 45545-2:2013+A1:2015: Fire protection of railway vehicles - Part 2: Requirement for fire behaviors of materials and components
Standard Brief
EN45545 This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by March 2016.
EN 45545 supersedes BS 6853, DIN5510-2,NFF16-101 national standards.
This European Standard exists in three official versions (English, French, German).
Scope
This part of EN 45545 specifies the reaction to fire performance requirements for materials and products used on railway vehicles as defined in EN 45545-1.
For each hazard level, this part specifies the test methods, test conditions and reaction to fire performance requirements.It is not within the scope of this European Standard to describe measures that ensure the preservation of the vehicles in the event of o fire.
Hazard levels
HL1, HL2, HL3
Test Method
EN 45545-2 R1: Surface Products
EN 45545-2 R10: Flooring Covering
EN 45545-2 R15, R16: Wire & Cable
EN 45545-2 R22/ R23: Interior seals, Electrical Equipment
EN 45545-2 R24 : Electrotechnical products
EN 45545-2 R24/R25 : PCB Printed circuit boards
EN 45545-2 R26 : Small electrotechnical products
Reference Standard
EN 45545-1: Fire Protection of railway Vehicles â?? Part 1: General
EN 45545-2: Requirement for fire behaviour of materials and components
EN 45545-3: Fire resistance requirements for fire barriers and partitions
EN 45545-4: Fire safety requirements for railway rolling stock design
EN 45545-5: Fire safety requirements for electrical equipment
EN 45545-6: Fire control and management system
EN 45545-7: Flammable liquid and flammable gas installations
We also can provide the following service of fire test to Railway
EN45545-2 Fire protection of railway vehicles: Requirement for fire behaviors of materials EN45545-3 Fire resistance requirements for fire barriers
NFPA 130 Standard for fixed guideway transit and passenger rail systems
DIN5510-2 Fire behaviour of materials and parts, classification, requirement
BS6853 Code of practice for fire precautions in the design and construction
NF F16-101 Railway Rolling Stock Fire Behavior Choice of Material
EN 45545-2:2013+A1:2015: Fire protection of railway vehicles - Part 2: Requirement for fire behaviors of materials and components
Standard Brief
EN45545 This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by March 2016.
EN 45545 supersedes BS 6853, DIN5510-2,NFF16-101 national standards.
This European Standard exists in three official versions (English, French, German).
Scope
This part of EN 45545 specifies the reaction to fire performance requirements for materials and products used on railway vehicles as defined in EN 45545-1.
For each hazard level, this part specifies the test methods, test conditions and reaction to fire performance requirements.It is not within the scope of this European Standard to describe measures that ensure the preservation of the vehicles in the event of o fire.
Hazard levels
HL1, HL2, HL3
Test Method
EN 45545-2 R1: Surface Products
EN 45545-2 R10: Flooring Covering
EN 45545-2 R15, R16: Wire & Cable
EN 45545-2 R22/ R23: Interior seals, Electrical Equipment
EN 45545-2 R24 : Electrotechnical products
EN 45545-2 R24/R25 : PCB Printed circuit boards
EN 45545-2 R26 : Small electrotechnical products
Reference Standard
EN 45545-1: Fire Protection of railway Vehicles â?? Part 1: General
EN 45545-2: Requirement for fire behaviour of materials and components
EN 45545-3: Fire resistance requirements for fire barriers and partitions
EN 45545-4: Fire safety requirements for railway rolling stock design
EN 45545-5: Fire safety requirements for electrical equipment
EN 45545-6: Fire control and management system
EN 45545-7: Flammable liquid and flammable gas installations
We also can provide the following service of fire test to Railway
EN45545-2 Fire protection of railway vehicles: Requirement for fire behaviors of materials EN45545-3 Fire resistance requirements for fire barriers
NFPA 130 Standard for fixed guideway transit and passenger rail systems
DIN5510-2 Fire behaviour of materials and parts, classification, requirement
BS6853 Code of practice for fire precautions in the design and construction
NF F16-101 Railway Rolling Stock Fire Behavior Choice of Material
Rail transit is one of the main means of transportation. Because of its limited space, it is difficult to escape. The fire performance of materials of railway vehicle has attracted more and more attention around the world.
There are two main standards of fire protection for railway vehicle, EU standard EN45545 and NFPA130.
EN 45545 Standards
EN 45545-2 Requirement for fire behaviors of materials and components
Fire Hazard LevelHL1HL2HL3
Product CategoryR1 R26
Test MethodISO5658-2ISO5660-1 ISO9239-2 ISO4589-2ISO5659-2NFX70-100
EN 45545-3 Fire resistance requirements for fire barriers
NFPA 130 American Standard
NFPA 130 Standard for fixed guideway transit and passenger rail systems
Test Items Surface Flammability, Smoke Density, Heat Release
Test method
TB/T 3237 Chinese Fire test standard for railway vehicles - Standard
TB/T 3237 Flame retardant technical specification of decorating materials for multiple unit train
TB/T 3237 Chinese Fire test standard for railway vehicles Test Method
GB 2406 Oxygen index test
UIC 564 Combustion test
GB 8323 Smoke density test
TB 3237 Part 4.4 Smoke toxicity test
TB/T 3237 Chinese Fire test standard for railway vehicles Scope
This Standard is applicable to the flame retardant decorating materials for the multiple unit train with an operation speed larger than or equal to 200km/h.
This Standard specifies the flame retardant property requirements and test methods for the decorating materials for multiple unit train.
TB/T 3237 Chinese Fire test standard for railway vehicles Reference Standard
GB/T 2406.2 Plastics - Determination of Burning Behavior by Oxygen Index
GB/T 10707 Rubber - Determination of the Burning
GB/T 8323.2 Determination of Optical Density by a Single-chamber Test
UIC 564-2 Regulations relating to fire protection
We also can provide the following service of fire test to Railway
EN45545-2 Fire protection of railway vehicles: Requirement for fire behaviors of materials EN45545-3 Fire resistance requirements for fire barriers
NFPA 130 Standard for fixed guideway transit and passenger rail systems
DIN5510-2 Fire behaviour of materials and parts, classification, requirement and test methods
BS6853 Code of practice for fire precautions in the design and construction of passenger carrying trains
NF F16-101 Railway Rolling Stock Fire Behavior Choice of Material
CASfire Technical Co.,Ltd have rich experience to provide fire test to upholstered furniture and textile
Fire test to upholstered furniture Products Scope
Upholstered Furniture - Sofa Mattress and Bedding Components
Sofa
Upholstered Seat
Seat Cushion
Sofa covering
Filled foam Mattress Emulsion foam,etc
Liner
The ASTM E595 test is mainly derived from NASA and is a gas release test conducted in a vacuum environment. Under vacuum conditions, material venting and structural venting are common phenomena that have a significant impact on the normal and stable operation of high-tech equipment and aviation components.
We have rich experience in these materials, including: thermal conductive silica gel, thermal conductive silicone rubber, copper clad laminate, fluororubber dust plug FKM, electromagnetic shielding film, EPDM protective plug, dust plug, adhesive, optical adhesive, hot melt adhesive, thermal conductive gel, SMC grid plate, TPU fire proof and anti-static elastomer, plastic, PP, PC, paint baking steel plate, PCD, etc
ASTM E595-15 Outgassing test - Test Standard
ASTM E595 Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment
ASTM E595-15 Outgassing test - Test Requirement
CVCM ï¼?collected volatile condensable materialsï¼?â?¤0.1%
TML ï¼?total mass lossï¼?â?¤1%
WVR ï¼?the amount of water vapor regainedï¼?
Outgassing test ASTM E595 - Test Conditions
Pre Condition: 73 F/ 50% RH (24Hours) ; Post Condition: 73 F/ 50% RH (24Hours)
This test method describes the test apparatus and related operating procedures for evaluating the mass loss of materials being subjected to 125�°C at less than 7*10â??3 Pa for 24 h. The overall mass loss can be classified into noncondensables and condensables. The latter are characterized herein as being capable of condensing on a collector at a temperature of 25�°C.
More about Outgassing test ASTM E595,please contact us :
TB/T 3237 Chinese Fire test standard for railway vehicles - Standard
TB/T 3237 Flame retardant technical specification of decorating materials for multiple unit train
TB/T 3237 Chinese Fire test standard for railway vehicles â?? Test Method
GB 2406 Oxygen index test
UIC 564 Combustion test
GB 8323 Smoke density test
TB 3237 Part 4.4 Smoke toxicity test
TB/T 3237 Chinese Fire test standard for railway vehicles â?? Scope
This Standard is applicable to the flame retardant decorating materials for the multiple unit train with an operation speed larger than or equal to 200km/h.
This Standard specifies the flame retardant property requirements and test methods for the decorating materials for multiple unit train.
TB/T 3237 Chinese Fire test standard for railway vehicles â?? Reference Standard
GB/T 2406.2 Plastics - Determination of Burning Behavior by Oxygen Index
GB/T 10707 Rubber - Determination of the Burning
GB/T 8323.2 Determination of Optical Density by a Single-chamber Test
UIC 564-2 Regulations relating to fire protection
CASfire Technical Co.,Ltd
8F Building 4, Chinese Academy of Science,
No.255 South Duiying Road,Jimei, Xiamen 361021, China
Tel: (+86) 0592-3500085
MP: (+86) 18906059211
Email: info@casfire.cn
Website: http://www.casfire.cn
ASTM E595-15 Outgassing test - Test Standard
ASTM E595 Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment
ASTM E595-15 Outgassing test - Test Requirement
CVCM ï¼?collected volatile condensable materialsï¼?â?¤0.1%
TML ï¼?total mass lossï¼?â?¤1%
WVR ï¼?the amount of water vapor regainedï¼?
Outgassing test ASTM E595 - Test Conditions
Pre Condition: 73 F/ 50% RH (24Hours) ; Post Condition: 73 F/ 50% RH (24Hours)
This test method describes the test apparatus and related operating procedures for evaluating the mass loss of materials being subjected to 125�°C at less than 7*10â??3 Pa for 24 h. The overall mass loss can be classified into noncondensables and condensables. The latter are characterized herein as being capable of condensing on a collector at a temperature of 25�°C.
ASTM E595-15 Outgassing test â?? Brief
Many types of organic, polymeric, and inorganic materials can be tested. These include polymer potting compounds,foams, elastomers, films, tapes, insulations, shrink tubings,
adhesives, coatings, fabrics, tie cords, and lubricants. The materials may be tested in the â??as-receivedâ?? condition or prepared for test by various curing specifications.
More about Outgassing test ASTM E595,please contact us :
CASfire Technical Co.,Ltd
8F Building 4, Chinese Academy of Science,
No.255 South Duiying Road,Jimei, Xiamen 361021, China
Tel: (+86) 0592-3500085
MP: (+86) 18906059211
Email: info@casfire.cn
Website: http://www.casfire.cn
ASTM E595-15 Outgassing test - Test Standard
ASTM E595 Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment
ASTM E595-15 Outgassing test - Test Requirement
CVCM collected volatile condensable materialsï 0.1%
TML total mass loss
WVR the amount of water vapor regained
Outgassing test ASTM E595 - Test Conditions
Pre Condition: 73 F/ 50% RH (24Hours) ; Post Condition: 73 F/ 50% RH (24Hours)
This test method describes the test apparatus and related operating procedures for evaluating the mass loss of materials being subjected to 125 C at less than Pa for 24 h. The overall mass loss can be classified into noncondensables and condensables. The latter are characterized herein as being capable of condensing on a collector at a temperature of 25 C.
ASTM E595-15 Outgassing test Brief
Many types of organic, polymeric, and inorganic materials can be tested. These include polymer potting compounds,foams, elastomers, films, tapes, insulations, shrink tubings,
adhesives, coatings, fabrics, tie cords, and lubricants. The materials may be tested in the condition or prepared for test by various curing specifications.
More about Outgassing test ASTM E595
TB/T 3237 Flame retardant technical specification of decorating materials for multiple unit train.
Test Method:
GB 2406 Oxygen index test
UIC 564 Combustion test
GB 8323 Smoke density test
TB 3237 Part 4.4 Smoke toxicity test
Reference Standard:
GB/T 2406.2 Plastics - Determination of Burning Behavior by Oxygen Index
GB/T 10707 Rubber - Determination of the Burning
GB/T 8323.2 Determination of Optical Density by a Single-chamber Test
UIC 564-2 Regulations relating to fire protection
HPD Product Health Claim Certification - Overview
HPD or PHD certification Healthy Products Declaration)is proposed and issued by the Product Health Declaration Cooperative Organization, with a standard report form of product health and safety content instructions, to explain the health and safety of Products to the public.Companies applying for HPD certification must declare all known toxic or hazardous substances contained in the product.The Healthy Product Claim focuses on the environmental and social benefits of products, energy sustainability and also contributes to a healthy built environment.
HPD product Health claim certification is a new LEED V4 requirement In order to obtain higher LEED V4 material composition and optimal material composition credits for building materials disclosure, companies need to disclose all ingredients that account for more than 1/1000 of their products.Collecting health product claims for at least 20 products is one way to earn LEED points and is one way to keep track of ingredients.This is a flexible tool to meet criteria and earn points.HPD, released under version 2.1 and later, provides a way to pre-filter LEED requirements.For convenience, health product claims that pass pre-check can be found in the HPD public repository by simply using the search bar.
HPD Product Health claim certification - beneficial
Comply with LEEDv4, WELL and other certification standards
Flexible reporting of risks and disclosures
Meet consumer demand for material transparency
Saving cost and time, meeting C2C and Declare requirements
HPD Health Product Claims qualify companies for numerous green building certification
WELL the certification
LEED certification
Green Star certification
Google Portico certification
HPD product health claim certification - certification process
Apply for registration
Data collection (List of material components)
Create HPD (cooperate with toxicologist, determine CAS code, identify potential health hazard components)
Verify HPD you can choose an independent third party to verify
Publish HPD optionally add HPD report to international public repository
Product environmental certification - related standards
EPD Environmental Product Declaration
PHD/HPD Health Product Declaration
TB/T 3237 Flame retardant technical specification of decorating materials for multiple unit train
Scope
This Standard is applicable to the flame retardant decorating materials for the multiple unit train with an operation speed larger than or equal to 200km/h.
This Standard specifies the flame retardant property requirements and test methods for the decorating materials for multiple unit train.
Test Method
GB 2406 Oxygen index test
UIC 564 Combustion test
GB 8323 Smoke density test
TB 3237 Part 4.4 Smoke toxicity test
Reference Standard
GB/T 2406.2 Plastics - Determination of Burning Behavior by Oxygen Index
GB/T 10707 Rubber - Determination of the Burning
GB/T 8323.2 Determination of Optical Density by a Single-chamber Test
UIC 564-2 Regulations relating to fire protection
We also can provide the following service of fire test to Railway
EN45545-2 Fire protection of railway vehicles: Requirement for fire behaviors of materials EN45545-3 Fire resistance requirements for fire barriers
NFPA 130 Standard for fixed guideway transit and passenger rail systems
DIN5510-2 Fire behaviour of materials and parts, classification, requirement and test methods
BS6853 Code of practice for fire precautions in the design and construction of passenger carrying trains
NF F16-101 Railway Rolling Stock Fire Behavior Choice of Material
DIN5510-2: Preventive fire protection in railway vehicles; Part 2: Fire behaviour and fire side effects of materials and parts, classification, requirement and test methods.
Non-flooring material:
DIN54837 and ISO 5659-2 FED Toxicity for S2-S5,SR1/SR2,ST1/ST2
Flooring covering: ISO9239-1 for SF1-SF3 and ISO 5659-2 FED toxicity
Small Parts: DIN53438-2 / DIN53438-3 for K1-K3 or F1-F3
Seats: DIN 54341ã??EN1021ã??ISO9705
Cable and Wire: EN 60332-1-2ã??EN50266-2-4/5ã??EN 61034ã??EN 50305
Small Electrical parts: EN 60695-11-10ã??ISO4589-2
Test method
> DIN 54837: Small Parts combustion test
> EN ISO 9239-1: extension of the flame test - Floor
> DIN 53438-2: Flammable Material Testing
> DIN EN 60332-1-2: single cable Vertical Burning Test
> DIN EN 61034-1: Wire & Cable Smoke Density Test
> DIN EN 50266-2-4: Vertical Burning Test for punch cable
> DIN EN 1021-1: Seat Burning Test
> DIN EN ISO 5659-2: Smoke Toxicity Test
We also can provide the following service of fire test to Railway
EN45545-2 Fire protection of railway vehicles: Requirement for fire behaviors of materials EN45545-3 Fire resistance requirements for fire barriers
NFPA 130 Standard for fixed guideway transit and passenger rail systems
DIN5510-2 Fire behaviour of materials and parts, classification, requirement and test methods
BS6853 Code of practice for fire precautions in the design and construction of passenger carrying trains
NF F16-101 Railway Rolling Stock Fire Behavior Choice of Material
CASfire Technical Co.,Ltd have rich experience to provide ISO 4589-2: Oxygen Index Test to Plastics Material.
EN ISO 4589-2: Plastics Determination of burning behaviour by oxygen index â?? Part 2: Ambient- temperature test.
EN ISO 4589-2:Oxygen Index Test to Plastics Material - Scope
This part of ISO 4589 specifies methods for determining the minimum concentration of oxygen,
in admixture with nitrogen, that will support combustion of small vertical test specimens under
specified test conditions. The results are defined as oxygen index values.
Methods are provided for testing materials that are self-supporting in the form of vertical bars or sheet up to 10,5 mm thick. These methods are suitable for solid, laminated or celluar materials characterized by an apparent density greater than 100 kg/m3.
The methods may also be applicable to some cellular materials having an apparent density of less than 100 kg/m3. A method is provided for testing flexible sheet or film materials while supported vertically. For comparative purposes, a procedure is provided for determining whether or not the oxygen index of a material lies above some specified minimum value.
Oxygen index results obtained using the methods described in this part of ISO 4589 can provide a sensitive measure of the burning characteristics of materials under certain controlled laboratory conditions, and hence may be useful for quality control purposes. The results obtained are dependent upon the shape, orientation and isolation of the test specimen and the conditions of ignition. For particular materials or applications, it may be necessary or appropriate to specify different test conditions. Results obtained from test specimens of differing thickness or by using different ignition procedures may not be comparable and no correlation with flammability behaviour under other fire conditions is implied.
Results obtained in accordance with this part of ISO 4589-2 must not be used to describe or appraise the fire hazard presented by a particular material or shape under actual fire conditions, unless used as one element of a fire risk assessment that takes into account all of the factors pertinent to the assessment of the fire hazard of a particular application for the material.
