Pneumatic slotting machine: Pneumatic slotting machine about 20 kg weight, with a pneumatic drive slotted, pneumatic material, the use of very safe, very convenient
Equipped with speed angle grinder, double compass slider, manual double folder feeder, slot is very convenient, with the word row hole hole software, the use of more convenient
Slotting machine with speed control angle grinder can be used with a variety of blade processing all kinds of sidebelt, tungsten steel blade can open metal sideband, stainless steel sideband will not be black, tungsten steel blade must be transferred to 1000 rpm / Minute (speed adjustable angle grinder 2 files), alloy blade can be used to open aluminum and aluminum coil, the use of angle grinding machine is best not to adjust too fast, easy to fly out of the aluminum side of the waste, Protect the blade!
Slotting machine is the depth of the screw bar (fine-tuning), fine-tuning, then it is not easy to damage the blade, you can also better operate the slot machine, better adjust the slot depth!
Resin luminous characters are now relatively high prices in the industry, and more high-end a luminous characters, many big brands are using resin words, the following words about the production of resin word:
Step one: Now the popular resin word is the first floor and the first edge of the first welding, the floor is carved with a plasma, and then the edge of the welding on it.
Step 2: is to be in the top of the word pad a layer of transparent acrylic, transparent acrylic carved out of the floor is slightly smaller, so that you can just set into the set before the acrylic get a few small pieces of acrylic good Position, set a location, stick on the edge, and then to the pad of acrylic, so you can keep parallel, but also easy to do the word, acrylic pad up after the must ensure that the seal, or else the resin will flow to the following.
Step three: is the resin panel, and now the domestic resin is 3: 1 saturated resin, paste is more imported, uniform light agent is mostly concentrated, so that the proportion of resin is better control. Resin ratio is like this, with a plastic pot into the resin A (3: 1 resin, large bottles of 6 kg), and then add a light agent (see the mix after the light to see the effect of light, the amount of added, probably With the resin 3% -5%, different amount of uniform agent plus the amount is not the same), and then add the color paste, the proportion of the same color and the proportion of the same agent 3% -5%, and finally add the curing agent (The ratio of the curing agent to the resin is 1: 3). Note: resin mixing time must be uniform, 8 kg loaded each step need to stir for more than 15 minutes, the greater the weight, the longer the mixing time, there are resin when the room must be kept in a clean room, or resin There will be black spots, unsightly, when the night will be particularly evident.
-
Metal word mini bending machine: three 1cm diameter cylinder, two bending handle, the use of more convenient, plus light type, while welding edge bending, folding time can not fold too thick sideband is generally 0.6 side of the side the effect is better!
Stainless steel word production process:
Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one.
Here i would like to talk about the production of stainless steel word steps:
Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of.
Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot.
Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice.
Step four: the floor is installed on it.
-
Metal Sheet Benders Bend Curtains Stainless Steel Illuminated Bend Bend Bend Crimping Pliers Clamps
This product is for the advertising industry, hand-folding metal word time-consuming and laborious, inaccurate production of a bending tool, the use of mold bending angle principle, jib parallel movement, the inflection point is not accurate, the efficiency increased by 3 times. Small size and light weight without a fixed, edge edge welding, to solve the problems of bending metal sheet
Angular angle features: accurate angle, save time and effort, jib parallel movement, the edge of the die pressure folding point precision does not shift.
No edge word luminous weapon, the use of new mold folding angle principle, to subvert the traditional angle concept, angle efficiency increased by three times.
Is for the advertising industry manual angle metal word time-consuming, laborious, inaccurate and produced a bending tool.
It is small and light weight does not need to be fixed, you can take in the side of the side of the welding side of the welding
Bending speed, easy to use, effectively solve the advertising processing of metal sheet metal bending in the existence of various problems.
Product use of lever afterburner, jaw parallel movement, the edge of the mold pressure folding point precision does not shift
Metal sheet for the production of sheet metal, advertising word edge of the metal edge of exquisite.
Suitable height 80MM, the thickness of 0.5MM below the side, can fine-tune the bracket to ensure that the jaw and the panel vertical;
According to the edge of the thickness of the lever to adjust the best point of force, easy to complete the metal word production process angle.
Save time and effort, so that the production of metal as a whole flat, beautiful, refined, hand-made metal word necessary weapon.
-
Rolling round: the aluminum side of the luminous word round round, with three different diameter of the round, the effective folding height, but also with a triangular prism, can be slotted directly attached to the triangular column on the corner, corner bending arc when fixed In the table and then fold, the use of more convenient!
Aluminum side flat luminous word production process:
Equipment required: engraving machine, slotting machine
    Now the domestic market on the aluminum side is divided into three kinds, namely, aluminum, aluminum and aluminum-plastic side, but the aluminum-plastic edge of the aluminum content of how much less to see the needs of the guests. And these three kinds of side to do the effect is not the same, the aluminum word is relatively hard, suitable for outdoor, the color is painted or paint, is the cost and selected, and aluminum than the aluminum soft, more suitable for small characters , Do some big brands of small print, looks more high-end, aluminum-plastic side than the aluminum coil is even more soft.
    In fact, the aluminum side of the plane light word is very good to do, is also very simple, very easy to just start to do the word.
    Step one: the panel is the acrylic, carved directly engraved with a car on it.
    Step two: the edge, you can choose is a fully automatic slot machine or manual slot machine, fully automatic to a lot of convenience, do not have to mark, but you have to consider the automatic slotting function can not use alloy blade , If it is the best, can not choose the manual slot machine installed on the alloy blade to slot, opened the slot out of the effect will be very good, very straight angle is very three-dimensional.
    Step three: open a good edge of the edge of the edge of the arc on the first use of archer or hand to work about the small curvature of the tools must be used to get, arc do not have to do too accurate, get a rough on it , And then set in the panel, in turn, glue, fixed methods are many kinds, some with a long nail on the wooden table with the words of the edge of the word, this method is more trouble, is more cost savings, but effort, Some get a metal table, with a strong magnetic to withstand, so more convenient, and the cycle is very strong, if it is more permanent magnetic, basically no longer need to invest.
    Step 5: Adhesion of panel and edge. Because the panel is acrylic, so can not be welded, use glue, you can use glass glue or AB glue, but the glass glue to do more slowly, AB glue on the faster, 3-5 minutes on it, so The best way is to first layer of AB glue, and then AB glue above a layer of glass glue, so sticky word is very strong, if you worry about the cost can only AB glue, but the word more than 60 cm to die.
    Step 6: Adhesive the word shell in the bottom of the word piercing the screws, and then put the lamp installed on the bottom plate, the good screw on it.
-
Desktop electric slotting machine: desktop electric slot machine machine weighing about 20 kg, with a speed angle grinder, double compass slider, manual double folder feeder, slot is very convenient, with the word row hole hole software, use It is more convenient
Slotting machine with speed control angle grinder can be used with a variety of blade processing all kinds of sidebelt, tungsten steel blade can open metal sideband, stainless steel sideband will not be black, tungsten steel blade must be transferred to 1000 rpm / Minute (speed adjustable angle grinder 2 files), alloy blade can be used to open aluminum and aluminum coil, the use of angle grinding machine is best not to adjust too fast, easy to fly out of the aluminum side of the waste, Protect the blade!
Slotting machine is the depth of the screw bar (fine-tuning), fine-tuning, then it is not easy to damage the blade, you can also better operate the slot machine, better adjust the slot depth!
Resin luminous characters are now relatively high prices in the industry, and more high-end a luminous characters, many big brands are using resin words, the following words about the production of resin word:
Step one: Now the popular resin word is the first floor and the first edge of the first welding, the floor is carved with a plasma, and then the edge of the welding on it.
Step 2: is to be in the top of the word pad a layer of transparent acrylic, transparent acrylic carved out of the floor is slightly smaller, so that you can just set into the set before the acrylic get a few small pieces of acrylic good Position, set a location, stick on the edge, and then to the pad of acrylic, so you can keep parallel, but also easy to do the word, acrylic pad up after the must ensure that the seal, or else the resin will flow to the following.
Step three: is the resin panel, and now the domestic resin is 3: 1 saturated resin, paste is more imported, uniform light agent is mostly concentrated, so that the proportion of resin is better control. Resin ratio is like this, with a plastic pot into the resin A (3: 1 resin, large bottles of 6 kg), and then add a light agent (see the mix after the light to see the effect of light, the amount of added, probably With the resin 3% -5%, different amount of uniform agent plus the amount is not the same), and then add the color paste, the proportion of the same color and the proportion of the same agent 3% -5%, and finally add the curing agent (The ratio of the curing agent to the resin is 1: 3). Note: resin mixing time must be uniform, 8 kg loaded each step need to stir for more than 15 minutes, the greater the weight, the longer the mixing time, there are resin when the room must be kept in a clean room, or resin There will be black spots, unsightly, when the night will be particularly evident.
-
Product specifications: Cylindrical diameter 12mm hole size 8.1mm (with our 250W / 120W heating tube, dense thermal conductivity will not dry, to ensure that the heating core life) shovel width 16mm hole depth 33-35mm whole body copper
Tempering welding word Po Note: tampon welding word when used to preheat, preheat to the vent hole after the smoke to welding, welding the location of the tip and the location of the welding must be sticky dilute hydrochloric acid or Tin solder solution, so that welding will be strong, high-power heating core is to ensure high temperature to ensure a solid welding, copper head must be copper, and only copper can hang tin can be welded, when the middle of the welding when the pause, Electric iron regulator down a little, so the temperature will not drop, it will not dry, to ensure that the life of soldering iron.
Acrylic body luminous word Rewinding tool: specifically for three-sided luminous word production tools, 200 plus and minus 10 for acrylic, PVC, organic board and other materials processing, simple tool is very useful, narrow heating area of 100mm * 2.5mm * 2, both sides of the heat more uniform, not to burn the material, and there are springs inside the heating plate, so that the two sides closer to the material, there will not be heated up and down uneven situation!
Whole body luminous characters are now relatively low-end luminous words, around the edge and the panels are made of acrylic, do not need welding, directly with three seconds
Glue can be directly sticky, simple operation, simple equipment
Step one: first carved the panel, do a good job grinding
Step two: the acrylic side of the bar directly attached to the edge of the panel, began to bond, with acrylic bending machine processing, to the corner of the place with acrylic
Angle machine corner, arc where the use of acrylic bending arc to bend, the greater the curvature of the air can be used to blow the wind gun
Step three: the light cloth, the panel installed from behind to install
The width of the handle handle length of 8cm, the handle closed the widest width of 7cm, did not put the pliers have different width of the closure are different, if any questions please contact customer service and then shoot! the
The width of the hole is 9mm, can be used for 9mm and 12mm straw hat lamp beads, 12mm only need to clip a little on it, for the previous handle is too small, we now handle is 7-inch handle, than the market on the 5-inch handle to be much larger, more in line with the hand position.
-
Magnetic positioning device is the production of aluminum side of the word, aluminum-plastic edge of the big iron word one of the necessary auxiliary tools, due to aluminum, metal toughness, bending the word must be fixed when the top, with the positioner can work in the metal plate The font is fixed on the stage. I suggest you use the iron plate to do a word with the platform, 3 mm or so is very easy to use, so that the magnetic magnetic force can play very well, do more convenient to use the word. The middle of the hole reserved for the magnet is easy for you to take a strong magnetic, a simple screwdriver a pry can remove the strong magnetic.
Permanent magnet, magnetic force. Can help fixed the shape of the word, so that the panel and the profile closely, easy to glue. Compared to the traditional word bonding, with the magnetic more labor-saving, time-saving, more simple and convenient. Can greatly reduce the artificial, so the words, the skills of the workers can be reduced, the threshold of the word is also reduced.
Generally do at least more than 50 words enough, the word of the seam is large and small, the best size of the allocation of some of the words of the seam is big and small, if the word is large, the workers are more, you need 100 or so, Especially when the words to do aluminum, the words are fixed, AB glue, such as glue immediately after the glue, so that glue inside the plastic will not be in the solidification (AB glue 5 minutes dry, the word split plastic, plastic needle Have enough time to solidify, glue the needle will be very fast). The amount of this product is small, you can send courier, if the amount of large, it is best to send logistics, we will choose the most suitable for your customer shipping!
Precautions:
â? NdFeB strong magnetic material hard, crisp, strong magnetic field, to lightly put. When the strong magnet itself or with other iron suction or separation, be careful not to operate the impact! Otherwise easily caused by the collision and damage the magnet or pinch your fingers!
â?¡ when the magnet can not be separated from each other when the proposed flat push off, do not hard pull pry.
â?¢ strong magnet should be away from iron and easy to be magnetized items, such as monitors, bank cards, computers, television, mobile phones and so on.
-
Magnetic positioning device is the production of aluminum side of the word, aluminum-plastic edge of the big iron word one of the necessary auxiliary tools, due to aluminum, metal toughness, bending the word must be fixed when the top, with the positioner can work in the metal plate The font is fixed on the stage. I suggest you use the iron plate to do a word with the platform, 3 mm or so is very easy to use, so that the magnetic magnetic force can play very well, do more convenient to use the word. The middle of the hole reserved for the magnet is easy for you to take a strong magnetic, a simple screwdriver a pry can remove the strong magnetic.
Permanent magnet, magnetic force. Can help fixed the shape of the word, so that the panel and the profile closely, easy to glue. Compared to the traditional word bonding, with the magnetic more labor-saving, time-saving, more simple and convenient. Can greatly reduce the artificial, so the words, the skills of the workers can be reduced, the threshold of the word is also reduced.
Generally do at least more than 50 words enough, the word of the seam is large and small, the best size of the allocation of some of the words of the seam is big and small, if the word is large, the workers are more, you need 100 or so, Especially when the words to do aluminum, the words are fixed, AB glue, such as glue immediately after the glue, so that glue inside the plastic will not be in the solidification (AB glue 5 minutes dry, the word split plastic, plastic needle Have enough time to solidify, glue the needle will be very fast). The amount of this product is small, you can send courier, if the amount of large, it is best to send logistics, we will choose the most suitable for your customer shipping!
Precautions:
â? NdFeB strong magnetic material hard, crisp, strong magnetic field, to lightly put. When the strong magnet itself or with other iron suction or separation, be careful not to operate the impact! Otherwise easily caused by the collision and damage the magnet or pinch your fingers!
â?¡ when the magnet can not be separated from each other when the proposed flat push off, do not hard pull pry.
â?¢ strong magnet should be away from iron and easy to be magnetized items, such as monitors, bank cards, computers, television, mobile phones and so on.
-
Magnetic positioning device is the production of aluminum side of the word, aluminum-plastic edge of the big iron word one of the necessary auxiliary tools, due to aluminum, metal toughness, bending the word must be fixed when the top, with the positioner can work in the metal plate The font is fixed on the stage. I suggest you use the iron plate to do a word with the platform, 3 mm or so is very easy to use, so that the magnetic magnetic force can play very well, do more convenient to use the word. The middle of the hole reserved for the magnet is easy for you to take a strong magnetic, a simple screwdriver a pry can remove the strong magnetic.
Permanent magnet, magnetic force. Can help fixed the shape of the word, so that the panel and the profile closely, easy to glue. Compared to the traditional word bonding, with the magnetic more labor-saving, time-saving, more simple and convenient. Can greatly reduce the artificial, so the words, the skills of the workers can be reduced, the threshold of the word is also reduced.
Generally do at least more than 50 words enough, the word of the seam is large and small, the best size of the allocation of some of the words of the seam is big and small, if the word is large, the workers are more, you need 100 or so, Especially when the words to do aluminum, the words are fixed, AB glue, such as glue immediately after the glue, so that glue inside the plastic will not be in the solidification (AB glue 5 minutes dry, the word split plastic, plastic needle Have enough time to solidify, glue the needle will be very fast). The amount of this product is small, you can send courier, if the amount of large, it is best to send logistics, we will choose the most suitable for your customer shipping!
Precautions:
NdFeB strong magnetic material hard, crisp, strong magnetic field, to lightly put. When the strong magnet itself or with other iron suction or separation, be careful not to operate the impact! Otherwise easily caused by the collision and damage the magnet or pinch your fingers!
when the magnet can not be separated from each other when the proposed flat push off, do not hard pull pry.
strong magnet should be away from iron and easy to be magnetized items, such as monitors, bank cards, computers, television, mobile phones and so on.
-
Positioning clip 3 inch clip aluminum profile aluminum side of the stainless steel seiko luminous word glue fixed clip
Positioning clip unlimited luminous words aluminum profile aluminum side strip stainless steel seiko illuminated word sticker fixing clip 3 "clip.
-
Stainless steel bending pliers: 18 inch handle bending, bending more vigorous, bending clamp side of the two screws, the top of the screw is to adjust the elastic side of the clip, the more tight twist, the more tight edge, but can not twist Too tight, too tight words will lead to the time when the excessive pressure on the screws above the broken, bending clamp mainly for large-scale luminous word thick edge material processing, generally within 1.2 or less, 1.0 stainless steel, The best, long-term thickening of the plate will damage the bending clamp.
-
Alloy blade specifications: 8 teeth and 12 teeth diameter 95mm, diameter 2mm, suitable for use on a variety of angle grinder, mainly for luminous characters aluminum, aluminum coil slotting, alloy blade can be curled with the material slotted, After the fold is very consistent, very beautiful, slotted when equipped with the final speed or low speed corner grinder to use protective blades, alloy blades generally do not have much wear and tear, be careful to use can be used for a long time!
-
Conventional hole diameter: 2.5mm 3.2mm 3.5mm 4.2mm 4 specifications, red needle can be interchangeable, a punch can play a number of pliers specifications, if you buy a 3.5 punch, but also want to play 4.2 Of the hole, and then buy a set of 4.2 red punch can be used, the use of attention, 3.5mm punching pin should be used with 3.5mm rushed to use, or do not wear, a long time punch red can be used angle grinder gently Grinding can continue to use
-
Tungsten steel grinding head: specifically for the edge of the edge of the slotting machine to use, grinding head diameter 4mm, rod diameter 3mm, a box of 20, metal slotting wear less, stainless steel slotting wear is relatively large, stainless steel slotted simple or Select the desktop slotting machine or CNC slotting machine slot, slotting cost is relatively low!
Stainless steel word production process:
Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one.
Here I would like to talk about the production of stainless steel word steps:
Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of.
Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for Stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot.
Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice.
Step four: the floor is installed on it.
-
Positioning clip 4 inch clip aluminum profile aluminum side of the stainless steel Seiko luminous word glue fixed clip
Positioning clip 4 inch clip aluminum profile aluminum side of the stainless steel Seiko luminous word glue fixed clip.
-
Luminous characters with tin, tin content of 50%, suitable for a variety of luminous characters welding, a 0.7kg, tin must be with the welding word po, dilute hydrochloric acid or tin solder solution used, more efficient!
Temp heat welding word when used to preheat, preheat to the vent hole after the smoke to welding, welding tip position and welding position must be sticky dilute hydrochloric acid or tin solder solution, so welding will be solid , high-power heating core is to ensure that the high temperature to ensure a solid welding, copper head must be copper, and only copper can hang tin can be welded, when the middle of the welding when the pause, you can adjust the iron iron regulator, so the temperature will not fall, it will not dry, to ensure that the life of soldering iron!
Stainless steel word production process:
Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one.
Here i would like to talk about the production of stainless steel word steps:
Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of.
Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot.
Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice.
Step four: the floor is installed on it.
Pneumatic punching gun for galvanized iron plate stainless steel plate The product is widely used in the advertising industry. It is widely used in the metal plate. Easy to miss the problem to improve work efficiency
Tungsten steel blade: tungsten steel blade dedicated to the luminous word slot machine, specifically to open the fine word and other high-grade stainless steel word edge, slotted must be 1000 r / min about the speed, or knife edge is easy to collapse, collapse It is not easy to repair, it is best equipped with a depth adjustable slot machine, both to protect the blade, but also to protect equipment and materials! Tungsten steel blade diameter 9.8cm, diameter 2cm, ordinary angle grinder can be used!
Stainless steel word production process:
Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one.
Here I would like to talk about the production of stainless steel word steps:
Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of.
Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for Stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot.
Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice.
Step four: the floor is installed on it.
-
15 cm double-axis angle machine, two one-centimeter thick active splint, you can clip within 14 cm of the edge, metal sideband, stainless steel sideband, flat aluminum can be used, 1.0 or less thickness sideband can be used, fixed the use of the table on the top of the effect is particularly good, folding machine at the top with buttons, fastening plywood and heel rotation distance, with a long time will not be deformed, is the metal luminous words necessary tools, 15 cm double angle machine has 6 kg weight, use solid! processing angle 30-150 degrees!
Stainless steel word production process:
Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one.
Here i would like to talk about the production of stainless steel word steps:
Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of.
Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot.
Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice.
Step four: the floor is installed on it.
-
A round mouth pliers: gripper length 10cm, cylindrical diameter 1cm, you can process a variety of high edge, for the previous 5-inch small handle, now switch to 7-inch handle, more in line with hand type, very easy to use, can also assist welding!
Pliers handle length 11cm, two handles the widest position of 5.5cm, if in doubt please contact customer service and then shoot!
Stainless steel word production process:
Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one.
Here i would like to talk about the production of stainless steel word steps:
Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of.
Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot.
Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice.
Step four: the floor is installed on it.
-
1. Can be welded while cornering
2. Contains the ball shaft, to keep smooth
3. Lightweight tools, no need for fixed use
4. Can not be placed more than 1.5mm thick material (clip thickness of 1.5mm)
5. Processing angle: 45 to 135 degrees If you want to process less than 45 degrees of tool material, the first processing angle transferred to 45 degrees, then take out the tool material, with the second manual processing, to make a smaller angle
-
Welding word Po bend length of 13 cm, suitable for welding all kinds of metal luminous characters!
Copper head specifications Cylindrical diameter 12mm hole size 8.1mm (with our 250W / 120W heat pipe, dense thermal conductivity will not dry, to ensure that the heating core life) shovel width 16mm hole depth 33-35mm whole body copper
Tempering welding word Po Note: tampon welding word when used to preheat, preheat to the vent hole after the smoke to welding, welding the location of the tip and the location of the welding must be sticky dilute hydrochloric acid or Tin solder solution, so that welding will be strong, high-power heating core is to ensure high temperature to ensure a solid welding, copper head must be copper, and only copper can hang tin can be welded, when the middle of the welding when the pause, Electric iron regulator down a little, so the temperature will not drop, it will not dry, to ensure that the life of soldering iron.
Please note:
If your punch is not installed in our home to buy, red needle rush to do not shoot! Because the other punch and our structure is not the same, although the style is like, but not common! The
Note: punching punch punch punch for high-speed steel made, very durable, with a blunt after the angle grinding machine can be polished again, grinding sharp in the red needle, so do not often change the red needle , Punching punch punch punch with 2.5mm, 3.2mm, 3.5mm, 4.2mm four commonly used specifications, if there are other specifications or other shapes of the factory can be customized.
Punching is the grinding is a slope, all the time when there are some thick side of the sidebelt will not be punctured, just hit the words will be stuck in the inside, the customer will be mistaken for pliers problems, thick Sideband is there will be two under the ring, if the pliers have any questions please consult our customer service, customer service will solve problems for you.
-
Second generation luminous characters folding angle clamp metal word bending clamp advertising word pliers auxiliary weldingsecond generation luminous characters folding angle clamp metal word bending clamp advertising word pliers auxiliary weldingsecond generation luminous characters folding angle clamp metal word bending clamp advertising word pliers auxiliary welding.
-
Universal metal plate bending machine lightweight metal plate bending machine can be customized to a variety of width, sample on the sample 19cm effective folding length, other specifications, please contact customer service! can be folded all kinds of sheet metal, aluminum, iron, stainless steel it is all acceptable.
-
A generation of flat nose pliers: jaws long 10CM, square column diameter 1cm, you can process a variety of high edge, for the previous 5-inch small handle, now switch to 7-inch handle, more in line with hand type, very easy to use, can also assist welding!
Pliers handle length 11CM, two handles the widest position of 5.5cm, if in doubt please contact customer service and then shoot!
Stainless steel word production process:
Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one.
Here I would like to talk about the production of stainless steel word steps:
Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of.
Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for Stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot.
Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice.
Step four: the floor is installed on it.
Pliers handle length 11CM, two handles the widest position of 5.5cm, if in doubt please contact customer service and then shoot.
-
Laser welding machine supporting the edge of three sets of flexible curved edge stainless steel can bend three - piece
Laser welding machine supporting the edge of three sets of flexible curved edge stainless steel can bend three - piece
-
Full angle bending machine: metal edge full angle bending machine is equipped with three different diameter, you can fold different size of the arc, the effective folding height of 10cm, the best use of screws fixed on the table, the whole angle fold Bending machine mainly for metal sideband, metal sideband, stainless steel sideband, aluminum, aluminum coil and other luminous word sideband, is the first choice for light-emitting word small tool!
No side of the word production process:
Infinitely word is now more popular luminous words, usually in the home, or shops inside the word is relatively small, so the general use of a better curved side of the straight bend, the production is relatively simple
Step one: the panel is generally acrylic, engraving machine can be carved out
Step two: the edge of the words are generally iron edge, stainless steel edge, aluminum side of the three, aluminum side, iron sideband directly bent with the shape of the panel, inside the font marked full transparent AB glue (all transparent not shading) Stainless steel sideband, then the best slot in the shape, so the word will look better
Step three: floor cloth lights, and then the side of the hole to install the floor to complete!
-
1. If the mini-slot machine with the use of welding word, the welding effect will be better.
2. Slide operation: the installation of ball slide on the machine, the machine will minimize the error, the appropriate increase in lubricating oil maintenance can be.
3. Positioning system: can control the position of the blade to the panel.
Luminous characters metal slotting machine galvanized iron light portable slotting machine edge welding edge slotting machine.
-
Product specifications: Cylindrical diameter 12mm hole size 8.1mm (with our 250W / 120W heating tube, dense thermal conductivity will not dry, to ensure that the heating core life) shovel width 16mm hole depth 33-35mm whole body copper
Tempering welding word Po Note: tampon welding word when used to preheat, preheat to the vent hole after the smoke to welding, welding the location of the tip and the location of the welding must be sticky dilute hydrochloric acid or Tin solder solution, so that welding will be strong, high-power heating core is to ensure high temperature to ensure a solid welding, copper head must be copper, and only copper can hang tin can be welded, when the middle of the welding when the pause, Electric iron regulator down a little, so the temperature will not drop, it will not dry, to ensure that the life of soldering iron!
Double-axis angle machine, two pieces of a thick section of the activities of the splint, you can clip 10 cm within the edge of the edge of the metal sideband, stainless steel sideband, flat aluminum can be used, 0.8 within the thickness of the sideband can be used, fixed on the table On the use of the effect is particularly good, is the metal luminous words of the necessary tools, 10 cm double angle machine has 5 kg weight, the use of solid! Processing angle 30-150 degrees!
Stainless steel word production process:
Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one.
Here I would like to talk about the production of stainless steel word steps:
Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of.
Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for Stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot.
Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice.
Step four: the floor is installed on it.
-
Luminous word bending pliers small rounded corner bending pliers stainless steel word with curved clamp 10cm effective bending
Luminous word bending clamp iron stainless steel edge bending welding round mouth clamp 7 - shaped round mouth pliers.
-
Full angle bending machine: metal edge full angle bending machine is equipped with three different diameter, you can fold different size of the arc, the effective folding height of 10cm, the best use of screws fixed on the table, the whole angle fold Bending machine mainly for metal sideband, metal sideband, stainless steel sideband, aluminum, aluminum coil and other luminous word sideband, is the first choice for light-emitting word small tool!
No side of the word production process:
Infinitely word is now more popular luminous words, usually in the home, or shops inside the word is relatively small, so the general use of a better curved side of the straight bend, the production is relatively simple
Step one: the panel is generally acrylic, engraving machine can be carved out
Step two: the edge of the words are generally iron edge, stainless steel edge, aluminum side of the three, aluminum side, iron sideband directly bent with the shape of the panel, inside the font marked full transparent AB glue (all transparent not shading) Stainless steel sideband, then the best slot in the shape, so the word will look better
Step three: floor cloth lights, and then the side of the hole to install the floor to complete.
-
Product specifications: cylindrical diameter 12mm hole size 8.1mm (with our 250w / 120w heating tube, dense thermal conductivity will not dry, to ensure that the heating core life) shovel width 16mm hole depth 33-35mm whole body copper
Tempering welding word po note: tampon welding word when used to preheat, preheat to the vent hole after the smoke to welding, welding the location of the tip and the location of the welding must be sticky dilute hydrochloric acid or tin solder solution, so that welding will be strong, high-power heating core is to ensure high temperature to ensure a solid welding, copper head must be copper, and only copper can hang tin can be welded, when the middle of the welding when the pause, electric iron regulator down a little, so the temperature will not drop, it will not dry, to ensure that the life of soldering iron.
Pneumatic folding machine: pneumatic material design, foot pedal control press material, activities freely, more than ten kilograms of guaranteed material, folding height of 15CM, for a variety of luminous word side of the band angle, angle machine is best to use fixed In the table, easy to use!
No side of the word production process:
Infinitely word is now more popular luminous words, usually in the home, or shops inside the word is relatively small, so the general use of a better curved side of the straight bend, the production is relatively simple
Step one: the panel is generally acrylic, engraving machine can be carved out
Step two: the edge of the words are generally iron edge, stainless steel edge, aluminum side of the three, aluminum side, iron sideband directly bent with the shape of the panel, inside the font marked full transparent AB glue (all transparent not shading) Stainless steel sideband, then the best slot in the shape, so the word will look better
Step three: floor cloth lights, and then the side of the hole to install the floor to complete.
-
Pneumatic angle machine: pneumatic binder design, foot pedal control press material, activities freely, more than ten kilograms of guaranteed material, folding height 10CM, applicable to a variety of luminous word side of the band angle, angle machine is best to use fixed In the table, easy to use!
No side of the word production process:
Infinitely word is now more popular luminous words, usually in the home, or shops inside the word is relatively small, so the general use of a better curved side of the straight bend, the production is relatively simple
Step one: the panel is generally acrylic, engraving machine can be carved out
Step two: the edge of the words are generally iron edge, stainless steel edge, aluminum side of the three, aluminum side, iron sideband directly bent with the shape of the panel, inside the font marked full transparent AB glue (all transparent not shading) Stainless steel sideband, then the best slot in the shape, so the word will look better
Step three: floor cloth lights, and then the side of the hole to install the floor to complete.
-
