Pneumatic slotting machine: Pneumatic slotting machine about 20 kg weight, with a pneumatic drive slotted, pneumatic material, the use of very safe, very convenient Equipped with speed angle grinder, double compass slider, manual double folder feeder, slot is very convenient, with the word row hole hole software, the use of more convenient Slotting machine with speed control angle grinder can be used with a variety of blade processing all kinds of sidebelt, tungsten steel blade can open metal sideband, stainless steel sideband will not be black, tungsten steel blade must be transferred to 1000 rpm / Minute (speed adjustable angle grinder 2 files), alloy blade can be used to open aluminum and aluminum coil, the use of angle grinding machine is best not to adjust too fast, easy to fly out of the aluminum side of the waste, Protect the blade! Slotting machine is the depth of the screw bar (fine-tuning), fine-tuning, then it is not easy to damage the blade, you can also better operate the slot machine, better adjust the slot depth! Resin luminous characters are now relatively high prices in the industry, and more high-end a luminous characters, many big brands are using resin words, the following words about the production of resin word: Step one: Now the popular resin word is the first floor and the first edge of the first welding, the floor is carved with a plasma, and then the edge of the welding on it. Step 2: is to be in the top of the word pad a layer of transparent acrylic, transparent acrylic carved out of the floor is slightly smaller, so that you can just set into the set before the acrylic get a few small pieces of acrylic good Position, set a location, stick on the edge, and then to the pad of acrylic, so you can keep parallel, but also easy to do the word, acrylic pad up after the must ensure that the seal, or else the resin will flow to the following. Step three: is the resin panel, and now the domestic resin is 3: 1 saturated resin, paste is more imported, uniform light agent is mostly concentrated, so that the proportion of resin is better control. Resin ratio is like this, with a plastic pot into the resin A (3: 1 resin, large bottles of 6 kg), and then add a light agent (see the mix after the light to see the effect of light, the amount of added, probably With the resin 3% -5%, different amount of uniform agent plus the amount is not the same), and then add the color paste, the proportion of the same color and the proportion of the same agent 3% -5%, and finally add the curing agent (The ratio of the curing agent to the resin is 1: 3). Note: resin mixing time must be uniform, 8 kg loaded each step need to stir for more than 15 minutes, the greater the weight, the longer the mixing time, there are resin when the room must be kept in a clean room, or resin There will be black spots, unsightly, when the night will be particularly evident. -
Metal word mini bending machine: three 1cm diameter cylinder, two bending handle, the use of more convenient, plus light type, while welding edge bending, folding time can not fold too thick sideband is generally 0.6 side of the side the effect is better! Stainless steel word production process: Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one. Here i would like to talk about the production of stainless steel word steps: Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of. Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot. Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice. Step four: the floor is installed on it. -
Metal Sheet Benders Bend Curtains Stainless Steel Illuminated Bend Bend Bend Crimping Pliers Clamps This product is for the advertising industry, hand-folding metal word time-consuming and laborious, inaccurate production of a bending tool, the use of mold bending angle principle, jib parallel movement, the inflection point is not accurate, the efficiency increased by 3 times. Small size and light weight without a fixed, edge edge welding, to solve the problems of bending metal sheet Angular angle features: accurate angle, save time and effort, jib parallel movement, the edge of the die pressure folding point precision does not shift. No edge word luminous weapon, the use of new mold folding angle principle, to subvert the traditional angle concept, angle efficiency increased by three times. Is for the advertising industry manual angle metal word time-consuming, laborious, inaccurate and produced a bending tool. It is small and light weight does not need to be fixed, you can take in the side of the side of the welding side of the welding Bending speed, easy to use, effectively solve the advertising processing of metal sheet metal bending in the existence of various problems. Product use of lever afterburner, jaw parallel movement, the edge of the mold pressure folding point precision does not shift Metal sheet for the production of sheet metal, advertising word edge of the metal edge of exquisite. Suitable height 80MM, the thickness of 0.5MM below the side, can fine-tune the bracket to ensure that the jaw and the panel vertical; According to the edge of the thickness of the lever to adjust the best point of force, easy to complete the metal word production process angle. Save time and effort, so that the production of metal as a whole flat, beautiful, refined, hand-made metal word necessary weapon. -
Rolling round: the aluminum side of the luminous word round round, with three different diameter of the round, the effective folding height, but also with a triangular prism, can be slotted directly attached to the triangular column on the corner, corner bending arc when fixed In the table and then fold, the use of more convenient! Aluminum side flat luminous word production process: Equipment required: engraving machine, slotting machine     Now the domestic market on the aluminum side is divided into three kinds, namely, aluminum, aluminum and aluminum-plastic side, but the aluminum-plastic edge of the aluminum content of how much less to see the needs of the guests. And these three kinds of side to do the effect is not the same, the aluminum word is relatively hard, suitable for outdoor, the color is painted or paint, is the cost and selected, and aluminum than the aluminum soft, more suitable for small characters , Do some big brands of small print, looks more high-end, aluminum-plastic side than the aluminum coil is even more soft.     In fact, the aluminum side of the plane light word is very good to do, is also very simple, very easy to just start to do the word.     Step one: the panel is the acrylic, carved directly engraved with a car on it.     Step two: the edge, you can choose is a fully automatic slot machine or manual slot machine, fully automatic to a lot of convenience, do not have to mark, but you have to consider the automatic slotting function can not use alloy blade , If it is the best, can not choose the manual slot machine installed on the alloy blade to slot, opened the slot out of the effect will be very good, very straight angle is very three-dimensional.     Step three: open a good edge of the edge of the edge of the arc on the first use of archer or hand to work about the small curvature of the tools must be used to get, arc do not have to do too accurate, get a rough on it , And then set in the panel, in turn, glue, fixed methods are many kinds, some with a long nail on the wooden table with the words of the edge of the word, this method is more trouble, is more cost savings, but effort, Some get a metal table, with a strong magnetic to withstand, so more convenient, and the cycle is very strong, if it is more permanent magnetic, basically no longer need to invest.     Step 5: Adhesion of panel and edge. Because the panel is acrylic, so can not be welded, use glue, you can use glass glue or AB glue, but the glass glue to do more slowly, AB glue on the faster, 3-5 minutes on it, so The best way is to first layer of AB glue, and then AB glue above a layer of glass glue, so sticky word is very strong, if you worry about the cost can only AB glue, but the word more than 60 cm to die.     Step 6: Adhesive the word shell in the bottom of the word piercing the screws, and then put the lamp installed on the bottom plate, the good screw on it. -
Desktop electric slotting machine: desktop electric slot machine machine weighing about 20 kg, with a speed angle grinder, double compass slider, manual double folder feeder, slot is very convenient, with the word row hole hole software, use It is more convenient Slotting machine with speed control angle grinder can be used with a variety of blade processing all kinds of sidebelt, tungsten steel blade can open metal sideband, stainless steel sideband will not be black, tungsten steel blade must be transferred to 1000 rpm / Minute (speed adjustable angle grinder 2 files), alloy blade can be used to open aluminum and aluminum coil, the use of angle grinding machine is best not to adjust too fast, easy to fly out of the aluminum side of the waste, Protect the blade! Slotting machine is the depth of the screw bar (fine-tuning), fine-tuning, then it is not easy to damage the blade, you can also better operate the slot machine, better adjust the slot depth! Resin luminous characters are now relatively high prices in the industry, and more high-end a luminous characters, many big brands are using resin words, the following words about the production of resin word: Step one: Now the popular resin word is the first floor and the first edge of the first welding, the floor is carved with a plasma, and then the edge of the welding on it. Step 2: is to be in the top of the word pad a layer of transparent acrylic, transparent acrylic carved out of the floor is slightly smaller, so that you can just set into the set before the acrylic get a few small pieces of acrylic good Position, set a location, stick on the edge, and then to the pad of acrylic, so you can keep parallel, but also easy to do the word, acrylic pad up after the must ensure that the seal, or else the resin will flow to the following. Step three: is the resin panel, and now the domestic resin is 3: 1 saturated resin, paste is more imported, uniform light agent is mostly concentrated, so that the proportion of resin is better control. Resin ratio is like this, with a plastic pot into the resin A (3: 1 resin, large bottles of 6 kg), and then add a light agent (see the mix after the light to see the effect of light, the amount of added, probably With the resin 3% -5%, different amount of uniform agent plus the amount is not the same), and then add the color paste, the proportion of the same color and the proportion of the same agent 3% -5%, and finally add the curing agent (The ratio of the curing agent to the resin is 1: 3). Note: resin mixing time must be uniform, 8 kg loaded each step need to stir for more than 15 minutes, the greater the weight, the longer the mixing time, there are resin when the room must be kept in a clean room, or resin There will be black spots, unsightly, when the night will be particularly evident. -
Luminous characters with tin, tin content of 50%, suitable for a variety of luminous characters welding, a 0.7kg, tin must be with the welding word po, dilute hydrochloric acid or tin solder solution used, more efficient! Temp heat welding word when used to preheat, preheat to the vent hole after the smoke to welding, welding tip position and welding position must be sticky dilute hydrochloric acid or tin solder solution, so welding will be solid , high-power heating core is to ensure that the high temperature to ensure a solid welding, copper head must be copper, and only copper can hang tin can be welded, when the middle of the welding when the pause, you can adjust the iron iron regulator, so the temperature will not fall, it will not dry, to ensure that the life of soldering iron! Stainless steel word production process: Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one. Here i would like to talk about the production of stainless steel word steps: Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of. Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot. Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice. Step four: the floor is installed on it.
Conventional hole diameter: 2.5mm 3.2mm 3.5mm 4.2mm 4 specifications, red needle can be interchangeable, a punch can play a number of pliers specifications, if you buy a 3.5 punch, but also want to play 4.2 Of the hole, and then buy a set of 4.2 red punch can be used, the use of attention, 3.5mm punching pin should be used with 3.5mm rushed to use, or do not wear, a long time punch red can be used angle grinder gently Grinding can continue to use -
Tungsten steel grinding head: specifically for the edge of the edge of the slotting machine to use, grinding head diameter 4mm, rod diameter 3mm, a box of 20, metal slotting wear less, stainless steel slotting wear is relatively large, stainless steel slotted simple or Select the desktop slotting machine or CNC slotting machine slot, slotting cost is relatively low! Stainless steel word production process: Stainless steel words are all stainless steel, this metal is mainly installed in the interior, and more high-end, but the requirements for the relatively high technology, especially the welding of this one. Here I would like to talk about the production of stainless steel word steps: Step 1: panel production, usually flat, there are three-dimensional, three-dimensional, spherical and so irregular panels, spherical and other highlights is to use the plate slowly knock, the other pattern is engraving machine engraved of. Step two: the edge of the very simple, with a slotting machine first slot, and then facing the panel to slot, or hand-held slot machine to slot, where welding where the slot, it is convenient, but for Stainless steel edge of the knife when the wear and tear is relatively fast, nor too flexible, there are certain limitations, narrow places may not be able to slot. Step three: that is, welding this one is to see the welding master used a welding tool, and some with a soldering iron, and some use of argon arc welding, the funds allowed to use laser welding, are very good choice. Step four: the floor is installed on it. -
Positioning clip 4 inch clip aluminum profile aluminum side of the stainless steel Seiko luminous word glue fixed clip Positioning clip 4 inch clip aluminum profile aluminum side of the stainless steel Seiko luminous word glue fixed clip. -
Positioning clip 3 inch clip aluminum profile aluminum side of the stainless steel seiko luminous word glue fixed clip Positioning clip unlimited luminous words aluminum profile aluminum side strip stainless steel seiko illuminated word sticker fixing clip 3 "clip. -
