Rolling round: the aluminum side of the luminous word round round, with three different diameter of the round, the effective folding height, but also with a triangular prism, can be slotted directly attached to the triangular column on the corner, corner bending arc when fixed In the table and then fold, the use of more convenient!
Aluminum side flat luminous word production process:
Equipment required: engraving machine, slotting machine
    Now the domestic market on the aluminum side is divided into three kinds, namely, aluminum, aluminum and aluminum-plastic side, but the aluminum-plastic edge of the aluminum content of how much less to see the needs of the guests. And these three kinds of side to do the effect is not the same, the aluminum word is relatively hard, suitable for outdoor, the color is painted or paint, is the cost and selected, and aluminum than the aluminum soft, more suitable for small characters , Do some big brands of small print, looks more high-end, aluminum-plastic side than the aluminum coil is even more soft.
    In fact, the aluminum side of the plane light word is very good to do, is also very simple, very easy to just start to do the word.
    Step one: the panel is the acrylic, carved directly engraved with a car on it.
    Step two: the edge, you can choose is a fully automatic slot machine or manual slot machine, fully automatic to a lot of convenience, do not have to mark, but you have to consider the automatic slotting function can not use alloy blade , If it is the best, can not choose the manual slot machine installed on the alloy blade to slot, opened the slot out of the effect will be very good, very straight angle is very three-dimensional.
    Step three: open a good edge of the edge of the edge of the arc on the first use of archer or hand to work about the small curvature of the tools must be used to get, arc do not have to do too accurate, get a rough on it , And then set in the panel, in turn, glue, fixed methods are many kinds, some with a long nail on the wooden table with the words of the edge of the word, this method is more trouble, is more cost savings, but effort, Some get a metal table, with a strong magnetic to withstand, so more convenient, and the cycle is very strong, if it is more permanent magnetic, basically no longer need to invest.
    Step 5: Adhesion of panel and edge. Because the panel is acrylic, so can not be welded, use glue, you can use glass glue or AB glue, but the glass glue to do more slowly, AB glue on the faster, 3-5 minutes on it, so The best way is to first layer of AB glue, and then AB glue above a layer of glass glue, so sticky word is very strong, if you worry about the cost can only AB glue, but the word more than 60 cm to die.
    Step 6: Adhesive the word shell in the bottom of the word piercing the screws, and then put the lamp installed on the bottom plate, the good screw on it.
-
Ethanol alcohol distillation column 1. It is standard 95-96% alcohol equipment. Also it can distill pure water. 2.The distillation system has  three columns  and  continuous  distillation  process.The process is the  same as industrial(large scale) alcohol equipment.  Mash distillation  column distills  fermented  mash or light alcohol  to 50% alcohol ethanol . It has red copper bubble cap trays, standard design. It auto continuously feeds material liquid, auto continuously produces 50% alcohol ethanol and auto continuously discharges waste,  ethanol discharge in waste 0.05%, better than international standard requirements. The first rectification distillation  column  increases  alcohol degree  to 70-75% ,  separates  fusel oil and high boiling point  Impurities.  It auto discharges waste water,  ethanol discharge in waste 0.05%, better than international standard requirements. The second rectification distillation  column  increases alcohol degree to 95%,  separates low boiling point  impurities  like acetaldehyde and methanol . 3.  The rectification system uses  industrial(large scale) standard process, but the whole set alcohol equipments are installed in one frame, like integration  module, even  you can run it by a button.
Distillation column For Ethanol Alcohol Plant 1. It is standard 95-96% alcohol equipment. Also it can distill pure water. 2. The distillation system has three columns and continuous distillation process.The process is the same as industrial(large scale) alcohol equipment.     a. Mash distillation column distills fermented mash or light alcohol to 50% alcohol ethanol .  It has red copper bubble cap trays, standard design. It auto continuously feeds material liquid, auto continuously produces 50% alcohol ethanol and auto continuously discharges waste, ethanol discharge in waste ?¤0.05%, better than international standard requirements.     b. The first rectification distillation column increases alcohol degree to 70-75% , separates fusel oil and high boiling point Impurities. It auto discharges waste water, ethanol discharge in waste ?¤0.05%, better than international standard requirements.     c. The second rectification distillation column increases alcohol degree to 95%, separates low boiling point impurities like acetaldehyde and methanol . 3.  The rectification system uses  industrial(large scale) standard process, but the whole set alcohol equipments are installed in one frame, like integration module, even you can run it by a button.
Variable frequency regulation meatball forming machine /meatball process line / machine meatball shape machine,meatball production line The meatball forming machine adopts continuous output meatball system, which has high production efficiency, and is equipped with knives and shapers of different caliber, which can be replaced at will according to the requirements of users. The machine is mainly used to produce chicken balls, fish balls, shrimp balls, pork balls, beef balls, mutton balls, donkey balls, vegetable balls, seafood balls and other products. The main equipment of meatball production line includes meat planer, mincing machine, chopping and mixing machine, stuffing mixing machine, meatball machine, forming water tank, frying production equipment, etc. The machine is small in size, light in weight, low in noise, beautiful and generous, durable, easy to operate and maintain, efficient and energy-saving. The meat (FISH) balls produced are of good quality, smooth appearance, good roundness and uniform size. The frame body is made of 3mm thick stainless steel by bending and welding, which is solid for internal use. Wear resistant brass is used inside and outside the outlet. capacity 50-420pcs/min ,voltage 380V/50Hz .
Large Capacity Electric Candle Wax Melting Machine Square / Round Shape Basic Information Place of Origin: china Brand Name: wax melter machine Certification: CE Model Number: SS-wax melter/candle melting machine Minimum Order Quantity: 1 Unit/Units Large capacity electrical wax melter /candle melting machine Packaging Details: Wooden case package for Large capacity electrical wax melter /candle melting machine Delivery Time: 7-10 days delivery after get payment Payment Terms: L/C,T/T,Western Union Supply Ability: 100 Unit/Units per Month Large capacity electrical wax melter /candle melting machine
Water Pump suitable for Commercial vehicles,Cars
V4 Borewell Submersible Pumpset Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP) - Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. Single Phase available in 0.5 HP to 5.0 HP Three Phase available in 1.0 HP to 6.0 HP - Speed : 2880 RPM - Head Range : 10 Mtr. To 340 Mtr. - Discharge Range : 450 LPM to 12 LPM - Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0 - Degree of Protection : IP 58 - Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph - Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs, 2.2kW, 7.5 kW -1500 lbs. - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph Direct Online (D.O.L) - Maximum Starts Per Hour : 20 Times
Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic
Monoblock Pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - Mechanical seal is provided as per customers requirement Specification - Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 65 Mtr. - Maximum Flow Rate : 1450 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 100 X 80 and 100 X 100 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 mÃ?/sec (max.) - Ph Value : 6.5 to 8.5 Material of construction - motor Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Monoblock pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. specification - Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 12 Mtr. - Maximum Flow Rate : 3160 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase - Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminum
