INTRODUCTION:
It is a kinds of Two-parts silicone, part A is flowable liquid silicon, part B is curing agent/catalyst ,which gets cured at room temperature 25 Centigrade within 3-6 hours or heating curing.This product is perfect for cement,concrete stone, GRC and GFRC products' mold making,such as the flower pot,fountain,Polyurethane Wood Imitation,Reinforced Plastic,Garden Decorations,fiberglass product and other decoration industries.
FEATURES:
1.High duplication times and no deformation
2.Excellent tear strength and tensile strength.
3.Good fluidity and good operability and good for both pouring method and pouring method.
4.Excellent flexibility and it is easy to demould.
5.It gets cured at room temperature 25 Centigrade within 3-6 hours.
6.Suitable hardness from 30 to 40 Shore A
OPERATION OF SILICONE RUBBER FOR CEMENT CASTING:
Step 1:Prepare the original mold
Weigh silicone&curing agent according to the mix ratio recommended,than remember to stir silicone & curing agent evenly,otherwise the silicon rubber will be partly solidified and bring problems in your final operation. Whats more, the finished molds will meet a short life.
Step 2:Vacuum pumping
Without exception, this step takes less than 10 minutes. Otherwise, it will cause cross linking reaction, and no more further steps will be available.
Step 3:Pouring casting or Brush operation
Step 4:After 3-5 hours later,demoulding the silicone mold,It will be better to use the mould after 24 hours.
APPLICATION:
This silicone is suitable for statues' mold making.
ABOUT US:
We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber.
What's more,our silicone rubber are environmental-friendly, with high safety and no toxic.You can absolutely trust your choice with us.
INTRODUCTION:
The series is and tear strength, 2-part liquid silicone rubber suitable for injection molding processes.
FEATURES:
1. High tensile strength
2. Good rebound property
3. Outstanding resistance to ageing
4. Low shrinkage
5. Low yellowing
6. Excellent thermal and cold stability
PACKAGING:
It is available in 20kg pails of 200kg drums
TYPICAL PROPERTY:
Appearance: Transparent;
Viscosity (mpas): 650,000~950,000;
Hardness: 20~70 Shore A;
Tensile Strength: 6.5~8.5 MPa;
Tear Strength: 20~35 KN/m;
Elongation at break: 330%~800%;
Linear shrinkage: 0.1%
REMARK:
The product should be closed tightly, protected from light and moisture, the shelf life is 12 months.
These figures are for reference only, please contact us for detail.
ABOUT US:
We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber.
What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.
INTRODUCTION:
This is a kind of room temperature vulcanized silicone rubber in condensation type. It's generally named as two part silicone rubber, Part A is a flowable liquid, part B is the curing agent or catalyst. It's mainly used for mold making.
This Silicone rubber is with good fluidity and moderate hardness which is suitable for middle size product with pattern by pouring operation, especially popular for manufacturer of resin crafts and gypsum decoration. Besides,
additive is available for brushing operation. It's one of our best selling silicone!
PRODUCT FEATURES:
*An exceptional fluidity and good operability, easy to demold
*Moderate hardness
*High tensile and tear strength
*Good flexibility
*Cure at room temperature
*Outstanding bubble releasing
*High duplication times
OPERATION INSTRUCTIONS OF MANUAL MOLD DESIGN MAKING LIQUID SILICONE RUBBER RAW MATERIALS:
Step 1: prepare the original molds
Step 2: Take 100G parts A and add 3G parts B and mix them evenly.
Step 3: Vacuum pumping
Step 4: Pouring casting or Brush operation
(For the detail of operation instructions,please contact us)
SHELF LIFE :
Twelve(12) months when stored under dry and cool place by original package under 25 Centigrade.
APPLICATION:
This silicone rubber is used for making molds of concrete stone,GRC, gypsum decoration, plaster ornaments, fiberglass products, polyester decoration, unsaturated resin crafts, polyresin crafts, polyurethane, bronze, wax, candle, and similar products .
ABOUT US:
We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber.
What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.
INTRODUCTION:
The component A of shoe Mold Silicone Rubber is white flowing liquid and the component B is the curing agent. For example, take silicone rubber of 100g and add 2% curing agent for mixing evenly. After the silicone rubber and the curing agent are completely mixed, put the silicon into a vacuum machine for deairing to remove the bubbles. After deaired, pouring the liquid silicone rubber into the product to be duplicated or into the mold frame.
FEATURES:
1.Two-component silicone rubber with tin-catalyst
2.Cured under room temperature
3.Low shrinkage
4.Excellent fexibility & easy demould
LIQUID RTV-2 SHOE MOLD SILICONE RUBBER NOTES:
Shoe mold silicone rubber is used for pouring or brushing technique. That is to say, fix the product or sole model to be duplicated onto a plane plate, then enclose the plane frame with wooden plates to prevent the leakage of the silicon , mix the silicone rubber and the curing agent evenly according to the mixing ratio of 100 : 2 and pour them onto the sole model, then brush evenly with a wooden plate or a brush, and fill up the mold frame with gypsum after the silicone rubber is dried.
APPLICATION:
Shoe mold silicone rubber is mainly used for shoe molds, sand casting, sole sampling, plaster models, simple products, products with non-complex patterns, as well as product models with stable size and non-deformation.
ABOUT US:
We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber.
What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.
For more information, welcome to contact Lilian:
Wechat / Phone: 8613617490457
E-mail: lilian(at)xrsil(dot)com
Skype: lilian-xrsilicone
Company:
Dongguan Xinrun Silicone New Materials Co., Ltd
Xinrun Group Limited
Factory address: No.2,Zhouliao Road, Langzhou Industrial Zone,Changping, Dongguan, Guangdong, China
INTRODUCTION:
Silicone Foams is a soft, two-component platinum silicone flexible foam that is versatile and easy to use. Vibrant colors can be achieved by adding color pigments. Cured foam is high heat resistance (will resist up to 350°F/176°C), water resistant, UV resistant and resists oxidation and ozone degradation.
FEATURE:
1.Mixed Viscocity
2.Very soft
3.Excellent temperature resistence
IMPROVE SURFACE FINISH AND MINIMIZE VOIDS WITH BACK PRESSURE:
Use a board that will completely cover the mold opening. Using a drill bit, drill 3 holes in the board spaced a few inches / cm apart. Make sure that, when the board is placed over the mold opening, the holes are over the mold cavity and rising foam will be able to make it through. Apply Ease Release 200 thoroughly too both sides of the board and into the drilled holes. Mix and pour foam into mold cavity and place board over mold opening. Hold board firmly in place. As foam rises in the mold cavity, some foam will grow out of the drilled holes. After the foam stops growing, you can let go of the board. Do not demold for at least 20 minutes.
APPLICATION:
Silicone Foams can be used for a variety of industrial and special effects applications including making foam filled appliances, padding/seat cushioning, orthotics/orthopedics, potting and encapsulation of electrical circuits and vibration dampening.
ABOUT US:
We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber.
What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.
For more information, welcome to contact Lilian:
Wechat / Phone: 8613617490457
E-mail: lilian(at)xrsil(dot)com
Skype: lilian-xrsilicone
Company: Dongguan Xinrun Silicone New Materials Co., Ltd / Xinrun Group Limited
Factory address: No.2,Zhouliao Road, Langzhou Industrial Zone,Changping, Dongguan, Guangdong, China
FEATURES:
-Mixing ratio of catalyst 2%-5%
-Good flowability
-Great self-deaeration
-Very good heat resistance
-High thermal conductivity
-Outstanding release properties
-High tear resistance
-Low shrinkage
-Outstanding resistance to inhibition
-Good resistance to polyester resin and concrete
SHELF LIFE:
When stored at or below 32°C (89.6°F) in the original unopened containers, such silicone base and its curing agents have a usable life of 12 months.
PACKAGE:
Silicone Base is available in 1Kg, 5Kg, 20Kg, 25Kg and 200Kg containers. Curing Agents are available in 50g, 1Kg and 20Kg containers.
APPLICATIONS:
-Architectural Restoration
-Sculpting/Wax Casting
-Concrete/GRC Casting
-Gypsum/Plaster Decoration
-Polyester/Resin Crafts Molding
-Furniture Molding
-Candles Mold making
-Soaps Mold making
-Tire Molding
-Detailed reproduction of figurines, art objects and similar items
ABOUT US:
We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber.
What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.
INTRODUCTION:
It is a hydrophilic addition silicone rubber impression material, it contains two components, Part A is platinum catalyst, and Part B is hydrogen containing polysiloxane. This product comprises liquid material and powder material. The main raw material is a silicone oil, silicone resin, alumina, quartz powder and etc.
COMPOSITION:
Base components 350 g;
Catalyst component 350 g;
A white spoon;
A blue spoon
PHYSICAL PROPERTIES:
Appearance: Catalyst Components(White putty),
Base Components(Blue putty);
Mix ratio: 1:1
Pot life: > 60 seconds
Curing time(37C): < 5 min
Hardness(Shore A): 60
Permanent deformation (%):
