Sintered Wire Mesh Filter Element Feature 1. Sintered wire mesh filter element is surface filtration 2. Sintered wire mesh filter element is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. Sintered wire mesh filter element has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life Sintered Wire Mesh Filter Element Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Operation Temperature: â?¤ 816 Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
1.1-100 microns 2.Stainless steel,Copper, brass,titanium 3.OEM,Non-standard 4.Mesh sintered Material: stainless steel,brass,bronze Category: stainless steel powder sintering, stainless steel nets sintering, bronze powder sintering, mesh sintering Filtration precision: 2-150 micron Structure: flake, Cartridge, tube, tubular shape, the goblet, bowl, plate, tapered, T shape, Cap shape, cylindrical clavite, Housing Anping County Longyi Mesh Manufacture Co.,Ltd produing sintered disc filters consist of highly uniform, interconnected networks of pores with tortuous paths that trap solid particles in gas or liquid. Excellent depth filters with superior mechanical strength. Stainless Steel Type 316L withstands temperatures up to -100�°C in oxidizing and 600�°C in reducing environments. These filters can be cleaned by other methods, such as ultrasonic baths or reverse flow flushing. If your application requires even greater resistance to corrosion, temperature, wear, and vibration, other nickel-based alloys are available. Want more information or would like to receive a quote?
Product Introduction 40 Micron Stainless Steel Sintered Wire Mesh Filter Element is a type of filter that is made by sintering multiple layers of stainless steel wire mesh together. Sintering is a process that involves compacting and heating a material without melting it, which causes the particles to fuse together and form a solid mass. 40 Micron Stainless Steel Sintered Wire Mesh Filter Element consists of multiple layers of wire mesh that are stacked and then sintered together. The sintering process creates a solid bond between the wires, resulting in a robust and durable filter element that can withstand high temperatures, pressures, and corrosive environments. Parameter Material: stainless steel Grade:SS 316L, SS 304L, SS 316, SS 304 OD: Max. 200mm Length: Max. 1500mm Accuracy / Pore Size: 0.2um-200um Porosity: 30%-60% Temperature resistance: â?¤300â?? Technique: Sintering Process Surface: Smooth, clean and metallic Feature 40 Micron Stainless Steel Sintered Wire Mesh Filter Element has several advantages over other types of filters. First, it has a uniform and controlled pore size, which ensures consistent filtration performance. Second, it has a high dirt-holding capacity, which means that it can capture a large amount of contaminants before needing to be cleaned or replaced. Third, it has excellent mechanical strength, allowing it to withstand high pressures and mechanical stresses. Fourthly, it can be cleaned and reused, making them a cost-effective and environmentally friendly filtration solution.
Product Introduction The stainless steel wire mesh sintered filter element is a derivative product of stainless steel sintered mesh. In this filter material, the wire woven mesh is laminated and vacuum sintering to create a multilayer wire mesh, which is strong mechanically. The stainless steel metal sintered mesh filter structure generally contains five layers, which are divided into five parts: protective layer, filter layer, separation layer, support layer and reinforcement layer. The standard five-layer screen thickness is 1.7mm.Thermal and processability, it is a filter material with good filtering effect, high strength and long service life. Product parameters Name: Stainless steel wire mesh sintered filter element with high mechanical strength for oil pipeline filtration Structure: standard five layers Filtration accuracy: 2-200m Working temperature: -200-650 Size: customized Filtration accuracy: 1-200 microns Product Features 1. High mechanical strength 2. High temperature resistance, corrosion resistance 3. High filtering precision 4. Strong and durable 5. Easy to process 6. Easy to install. Applications Mainly used for pipeline filtration in petrochemical industry.
40 Micron Stainless Steel Sintered Wire Mesh Filter Element is a type of filter that is made by sintering multiple layers of stainless steel wire mesh together. Sintering is a process that involves compacting and heating a material without melting it, which causes the particles to fuse together and form a solid mass. Parameter Material:stainless steel Grade:SS 316L, SS 304L, SS 316, SS 304 OD: Max. 200mm Length: Max. 1500mm Accuracy / Pore Size: 0.2um-200um Porosity: 30%-60% Temperature resistance: â?¤300â?? Technique: Sintering Process Surface: Smooth, clean and metallic The function of each layer in the five-layer stainless steel wire mesh sintered filter element: Outer Protective Layer: The outermost layer of the filter element is usually a coarse mesh that serves as a pre-filter to capture larger particles and prevent them from clogging the finer inner layers. This layer also protects the finer inner layers from damage. Intermediate Protective Layer: The second layer is also a coarse mesh that provides additional protection to the finer inner layers. This layer helps to prevent the filter element from being damaged by high-pressure or high-velocity fluid flows. Inner Filter Layer: The third layer is composed of a finer mesh size and serves as the primary filter layer. This layer is responsible for capturing smaller particles that were not captured by the outer protective layers. Reinforcing Layer: The fourth layer is a coarser mesh size than the inner filter layer and serves as a reinforcing layer. It provides mechanical support to the inner filter layer and helps to prevent it from collapsing under high-pressure or high-velocity fluid flows. Inner Protective Layer: The fifth and final layer is the finest mesh size layer that provides additional protection to the inner filter layer. This layer captures the smallest particles and prevents them from passing through the filter element. Feature 40 Micron Stainless Steel Sintered Wire Mesh Filter Element has several advantages over other types of filters. First, it has a uniform and controlled pore size, which ensures consistent filtration performance. Second, it has a high dirt-holding capacity, which means that it can capture a large amount of contaminants before needing to be cleaned or replaced. Third, it has excellent mechanical strength, allowing it to withstand high pressures and mechanical stresses. Fourthly, it can be cleaned and reused, making them a cost-effective and environmentally friendly filtration solution. Application 1.Chemical Processing 2.Oil and Gas Industry 3.Food and Beverage Processing 4.Pharmaceuticals 5.Water Treatment
-Name:Titanium wire mesh -Material:TA1, TA2, GR2, GR3, R50250, Titanium alloy etc. -Mesh count: Plain weave up to 200 mesh, dutch weave up to 70x400 mesh -Wire diameter: 0.05mm-1.8mm -Width: 0.5m-2m -Feature: --Low density and high specific strength --Outstanding corrosion resistance. In the corrosion environment, the surface of high purity titanium mesh will form an oxidation film layer to protect wire mesh from being corroded. The layer is compect and insert, which has strong resistance to corrosion. It has excellent corrosiion resistance performance in below environment: seawater, wet chlorine, chlorite and hypochlorite solution, nitric acid, chromic acid, metal chlorides and organic salts etc. -Application: Shipbuilding, war industry manufacturing, chemical filter, mechanical filter, desalination filter, high temperature vacuum equipment, medicine filtration industries etc. - Titanium wire mesh, titanium mesh, titanium mesh screen
longyi wire mesh company provides the ultra fine nickel wire mesh, nickel alloy based wire mesh.. which is widely used in the battery, electronic battery,,, the mesh size can be from 1-600 mesh,
Description FLD stainless steel sintered wire mesh pleated filter elements / cartridges are made of woven wire cloth or sintered wire mesh or sintered fiber web. The pleated filter cartridge has a shape of candle in long and thin. so it is called candle filter/cartridge. The pleated candle filter is made with single or double layer of woven wire mesh, the perforated metal tube as support layer, welded together with bolts and caps on both ends. But some pleated filters are made without perforated metal as supporting layer. Candle pleated Filter Media: The Pleated candle Filter Elements are mainly three types: Stainless steel sintered fiber felt; sintered wire mesh and stainless steel woven wire mesh. Stainless Steel Sintered Fiber felt is a kind of durable and pleating filter medium, sintered into a graded pore structure. So the sintered metal fiber felt enjoy the advantages of high porosity rate, large efficiency filtration area, high dirt holding capacity and replaced. Features and Benefits 1.) Easy replacement; 2.) Corrosion resistance; 3.) Easy clean and reuse; 4.) Large filter area; 5.) High dirt holding capacity; 6.) Excellent anti-acid, anti-alkahi, resist-temperature, resist-wearing; resist-recycling; 7.) Low pressure drop due to high porosity; 8.) Long life span; 9.) Low pressure drop and low cost, Material: Filter Media Woven mesh or perforated or fiber metal felt, or wire woven cloth are made of stainless steel 304, 304L, 316, 316L, 317L, 904L, & Monel Hastelloy etc. Structure: 1. The outside protection cylinder made of perforated stainless steel plate protect the filter element from damage; 2. Imported sintered fiber metal felt enjoy supreme filtration and easy cleaning. 3. The pressure resistance of stainless steel tube supporting inside core reach 175 bar. Applicant: The stainless steel pleated candle filter/cartridge is used for filtering of hot gas, vapor, liquid filtration, widely used as the below industries: 2.) Petroleum, chemical fiber, chemical industry and electric power; 3.) Pharmaceutics, machinery, metallurgy, ceramics; 4.) Disposal of sewage, foodstuff and beverage, cosmetic etc. The following parameter will be confirmed before order: 1.) Size; 2.) Work pressure; 3.) Operation pressure; 4.) Material; 5.) Flange standard; 6.) Dielectric; After-sale service: 1.) Warranty period is 12 months; 2.) Our technology team will support you for forever; 3.) Engineering service is available for your machinery overseas
Materials: carbon steel and stainless steel (302,304,304L,316,316L etc). Characteristics:The welded stainless steel water well screen is made up of rods and warp. The rod can be round wire, triangular wire or trapezoid wire. The warp is triangular wire (V-shaped wire). Water well screens have a structure and high open area, as well as accurate slot dimension. At the same time, water well screen have heat-resisting, anti-corrosive, good machine capability, last long, safety and reliability and so on characteristics. It can be used in many kinds of medium filtering. Uses: The strainer is a kind of filtered water tubing with the perforation .it can use with the deep well pump, dive the water pump, also may use in the water-treating equipment, the environmental protection, the sea water transforms into the industrial water and life use water desalination treatment, running water treatment, water softening treatment, the petroleum industry: The petroleum product terminal filters and the chemical acid, the alkali liquid filters, the ethyl alcohol and so on the organic solution recycling filters. Continuous slots significantly increase discharge area,thus providing greater access to water-bearing zone . We can produce this pipe with diameter 80mm-550mm ,slot size 0.1mm-10mm,length 50mm-5850mm .
