Trimens Technology(wuxi) Co., Ltd.

Features: 1) High quality, high linearity DFB laser 2) Advanced pre-distortion function 3) 1U, 19 inch standard chassis, 220VAC, 50Hz switching power supply or others. 4) 750 or 862 MHz bandwidth, supporting most broadband transport applications. 5) Unique thermal design provides superior heat dissipation, increasing the reliability of your system. 6) Automatic gain control helps maintain constant RF drive level to laser for consistent performance. 7) An interface LCD display allows you to monitor the transmitters performance. In addition, RS232 helps you monitor your transmitter performance in a long-distance Specifications Item Unit Specification Bandwidth MHz 47-750 or 860 Optical Wavelength nm 1310 (í+ 20) Optical Output Power (í+ 0.25 dB) (4~20mW) all series Safety Power Shutdown Yes Input RF Power, Main (í+ 0.1 dB) dBµV 72.0(+3/-2) Isolation, Auxiliary to Main Input dBc -32 AGC Input Range dB í+ 3 Response Flatness (maximum) dB í+ 0.75 Response Slope dB 0 to 0.75 Input Impedance ª+ 75 Input Return Loss dB >14 RF Test Point (í+ 1.0 dB) dB -20 Carrier-to-Noise Ratio (CNR) dB >51.0 Composite Second Order (CSO) dBc í_60 Composite Triple Beat (CTB) dBc í_65 Powering V AC220í+10% Power Consumption (maximum) W 40 Mechanical Specifications Optical Connector FC/APC, or SC/APC RF Connector F-Type Dimensions (height í- width í- depth) cm 4.3í-48.5í-30.0 Environmental Specifications Ambient Temperature -25+65 Operating Temperature Range 0-50 Notes: Optical link budget that provides a C/N of 51 dB when loaded with 59 PAL-D channels over a 10km single fiber. Composite Triple Beat (CTB) is 65dBc typical (all models) Composite Second Order (CSO) is -60dBc typical (all models) Specifications are subject to change without notice. 6KG

Summarize The NE100 Optical transmission platform can be as a converge center of optical transmission system in headend and hub to increase network reliability, scalability and cost-effective deployments. NE100 provide high usable module density (up to 14 modules in 4RU chassis), smart management in local or through SNMP, simplified installation, optional redundant powering, hot-swappable modules. Features Convenient: Blind-mate RF adaptors on the back-plane. Simple insertionand removal of modules; vacuum fluorescent display and navigation buttons for use as a simple interface for local status monitoring and control High Density: Capable of accommodating up to 14 application modules in a 4RU chassis Universal: Application modules can be located in any slot. Hot-swappable Modules: All application modules are hot-swappable modules, time-delay and protection circuit inside Intelligence: CPU intelligent system controller, monitoring the output voltage of power module and the system temperature; Blue-Screen VFD display the work status of the system; Element Management interface and independent TCP/IP server, ease to manage remotely High Reliability: two additional slots in the rear accommodate the AC and/or DC power supplies (120/240 Vac or -48 Vdc). One is main power supply, another is redundant, heat switched automatically Configurations Chassis Model Descriptions NE100-H Housing (only),no power NE100-H1 Housing, 1 NE100-PSAC NE100-H2 Housing, 2 NE100-PSAC NE100-H3 Housing, 1 NE100-PSDC NE100-H4 Housing, 2 NE100-PSDC Powering Modules Model Descriptions NE100-PSAC AC Power Supply 180~264V,50/60Hz NE100-PSDC DC Power Supply,-48v Application Modules Module Descriptions TFT100-(output power,mw) Forward 1310nm Optical Transmitter 4~20mw TFR100 Forward optical receiver TRR100 Single Reverse Optical Receiver TRR120 Dual Reverse Optical Receiver TRT100F Reverse Optical Transmitter,FP TRT100D Reverse Optical Transmitter,DFB TRT100C Reverse Optical Transmitter,CWDM NE100-H Chassis Technical Specifications Items Specifications Dimensions(Hí-Wí-D) mm 177í-437í-550 Slots 14 Power supply AC,180~264v 50/60 Hz, or DC,-48V RF Connectors F-Type Weight kg 20 Ordering Information: Model Number Descriptions NE100-H Chassis (only),no power NE100-PSAC AC Power Supply 180~264V,50/60Hz NE100-PSDC DC Power Supply,-48v NE100-H1 Chassis, 1 NE100-PSAC NE100-H2 Chassis, 2 NE100-PSAC NE100-H3 Chassis, 1 NE100-PSDC NE100-H4 Chassis, 2 NE100-PSDC PS100 AC & DC Power Supplies Summarize The PSAC and PSDC are power supply modules that provide AC and DC voltages for the NE100 optical broadband transmission platform, the module is installed in the rear of the Housing accommodates two power supplies for true power source redundancy. When two power supplies are used, the load is shared between both supplies. If one supply fails, the other immediately picks up the additional load. Features 1. High reliability. 2. Low output voltage 3. Dual power supply hot-switched Specifications Input Voltage 180-270V 50HZ AC 40-72VDC DC Output +24.4V7A +5.4V 8A -5.4V 8A Efficiency >85% Note: PSDC-48V, -48V DC Power Supply. 10KG

1. Excellent photodiod 2. 1310nm and 1550nm two mode receiver 3. 862MHZ bandwidth,Bi-directional transmission 4. High reliability 5. GaAs amplifier module,4 high level output ports, low distortion 6. Excellent switching power supply 7. Return path optical transmitter: FP , DFB , CWDM available Specifications: Forward path Item Unit Specification Remark Optical Optical Wavelength nm 1310 or1550 Optical Input Power dBm +1.5 -5 Optical Connector FC/APC or SC/APC Optical Link Frequency Response dB í+1.5 Output level dBµV >104 Optical input power -1 dBm Return Loss at Output dB í¦16dBí_550MHz í¦14dB550-860MHz C/N dB í¦51 1) Connected with TOT13 optical transmitter,10KM opticalfiber plus the loss of optical passive,4%OMI. 2) RF output levelí¦104dBuV,optical input power -1dBm. CSO dB í¦60 CTB dB í¦65 Reverse Path Parameter Unit Specification Remark DFB FP RF Input dBmV 18 18 Optical Output Power mw 1~4 1 Input Return Loss dB

1310nm optical transmitter, with front panel digital display showing input level, which adopts high linearity dfb laser of famous brand in the world, and builds-in perfect pre-distortion adjustment circuit and laser apc, atc closed loop control circuit. All the operating parameters are controlled by microprocessor, and the lcd screen on the front panel can display relative operating status and the fault information. Cmot-1310 series is designed and produced by absorbing the advantages of all kinds of 1310nm transmitter from both home and abroad. Featured with high index, multi-function and high reliability, it is suitable for high-end subscribers application 1> adopt word-famous company (ortel, aoi selected by user) advanced dfb laser instrument; max output optical power reach 31mw in ortel laser. Our specialized 2 dfb design max. Output level comes to 31+31mw. Coaxial laser max. 10+10+10+10mw (4*10mw) 2>best looking and convenient design of the front panel digital display. 3> advanced fiber in/ rf in, fiber out function, transit longer distance. 4> add advanced rf pre-distortion circuit, to use as proofreading catv system most important ctb and cso index, and to improve c/n index. 5>use our own gaas( imported mmic) hybrid, assure good output level. 6>built-in perfect power output automatic control circuit and laser thermoelectricity refrigeratory temperature automatic control circuit, insures highest output index and longest life. 7>built-in microprocessor automatic control circuit makes dfb laser always in best work state. 8>front panel blue vfd display, shows various main work status parameters and realizes automatic fault alarm and network management monitor.

1550nm direct modulation optical transmitter with high index and agc function. It adopts high linearity and low chirp dfb laser, max. Output level comes to 10db. Built-in pre-distortion compensation and agc, apc, atc closed loop control, which improves the system index obviously. It can be used in fttx (â?¤10km) of second-grade service area (sub-headend), also can be used in wdm narrow-band multiplexing and ip/qam. Feastures: 1> low chirp, high linearity dfb laser, chirp compensation. 2> advanced front panel with digital display function 3> agc fiber/ rf in, fiber out. 4> dual module rf driver , high efficient laser pre-distortion adjustment. 5> full-automatic omi control, agc & mgc. 6> intuitionistic modulation status display. 7> built-in dual back-up power supply, switch automatically . 8> casing temperature auto-control, ensure the long life of the laser

Detail: pro-class:Optical Transmitter Pro-id:SYD8600-II Reliable optical output Laser thermoelectricity refrigerator Temperature-controlled circuit Mirco CPU control laser working state The micro-processor software provide the Function of digital indicating Error warning Network control Remote control.

Working temperature: -40¡æ~+75¡æ Trasmission range: 20/40/60/80/100km(sm) 2km(mm) Application: military, oil and gas, mines, security, broadcasting, tactical field lan.