Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Supplier: Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,
PC natural 100% pure pc without any coating MATERIAL: PC natural 100% pure pc without any coating CATEGORY: PC TYPE: Natural SPECIFICATION: Separate 25 kg bag and Mark per month 78 mt 100% pure pc without any coating ,post Industrial materials Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 1450$ - 1700$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days Our Commitment We are committed to delivering in accordance with the quality given, source and licensed in the field of scrap transportation. 2Lians always for the purpose of satisfying customers on the criteria of sustainability and fairness through high work efficiency
PRODUCT INFORMATION PRODUCT NAMEâ?¡ Sequoia 3000 Gloss Finish DESCRIPTION Sequoia 3000 Gloss Finish is a premium solvent based high gloss finish, it is an oil-modified alkyd enamel paint. It is easy to apply and forms a smooth, tough paint film which has excellent gloss, fungus resistance and durability. USAGE For decoration and protection. Suitable for all types of interior and exterior metal and wood surfaces BENEFITS High gloss and excellent gloss retention Excellent gloss fastness Excellent durability Washable PACK SIZE 1 litre, 5 litres COLOUR RANGE Refer to Sequoia 3000 Gloss Finish colour chart PERFORMANCE GUIDE CHEMICAL RESISTANCE Resistant to mild chemical fumes. Special paint systems required if surface is subject to constant chemical attack HEAT RESISTANCE Generally resistant to heat up to 0c. Discolouration will occur after a prolong time if surface is constantly heated WATER RESISTANCE Resistant to normal atmospheric humidity present. Will withstand repeated washing. Not suitable for surface immerse in water THEORETICAL COVERAGE 16-18 meter2 /liter. Note: Surface coverage will alter depending on condition of surface to be paint PRE-APPLICATION SURFACE PREPERATION Generally all surfaces to be coated must be free of dust, dirt, grease and other contaminants. If metal surface is contaminated with rust, sand the surface with sand paper or wire-brush and clean of dust. For optimal performance, new galvanized surface should be cleaned and degreased to ensure good adhesion PREVIOUSLY PAINTED SURFACEâ?¡All loose and flaking paint film must be removed. Surface must be free of dust, dirt, grease and other contaminants. If metal surface is contaminated with rust, sand the surface with sand paper or wire-brush and clean of dust. RECOMMENDED PAINT SYSTEM Types of Surface Undercoat (1 coat) Finish (2 coats) Wood REDWOOD white undercoat Metal SEQUOIA PROTECTIVE COATING OR NASA oxide SEQUOIA 3000 GLOSS PAINT PAINT APPLICATION THINNINGâ?¡ For normal use, thinning is not required. If required, add 1 part of white spirit (10%) to 10 part of paint. Note: Excessive thinning will affect the quality of the paint. DRYTIME Touch dry : 2 hours Hard dry/Recoat : 8 hours CLEAN UP â?¡Clean all equipment with white spirit immediately afteruse. Allow empty container to dry prior to disposal. PRODUCT DATA COMPOSITION â?¡Pigments: Lightfast organic pigment, lightfast inorganic pigment. Blinder : Organic Alkyd Solvent : White spirit
NEO ENAMEL Paints are based on the alkyds/drying oils which have hard films with gloss retention. The films show excellent brushing properties and very little tendency to yellowing on exposure to the environment. Products are carefully designed keeping the pigment volume concentration to get optimum gloss, washability, adhesion and durability. The product dries at room temperature by oxidation and polymerization. NeoSyntheic Enamels are used on various substrates like wood , metal furnitures, train coaches, automobiles industries etc. NEO ENAMEL products are available in 2 varieties : I GLOW Hi Gloss Enamel. X 2 General Purpose Enamel.
Product Description Nolifrit Ground Coat Porcelain Enamel Frit Features: 1, With very good adhesion, can dissolve much iron oxide in metal surface, makes very strong combination with metal body. 2, Can be combined with cover coat in high level. 3, With very good elasticity and compressive strength. Prevent and decrease damage due to mechanical stress. 4, With less viscosity and surface tension, its good for escape of gas when firing. Reduce bubbles on cover coat. To ensure the smooth surface of enamel products. 5, With suitable expansion coefficient similar as steel plate. ABOUT US vitreous enamel coating porcelain enamel steel grates enamel glaze fritHunan Noli Enamel Co., Ltd is the leader manufacturer of enamel frits & inorganic pigment in China. Now we have 30,000 M/T enamel frits and 2,000 M/T inorganic pigments annual capacity, 10,000 M/T RTU(Ready to use) powder and electro static powder. Our main products of enamel frits including ground coat, cover coat, transparent frit , matt enamel, direct on black frits and various cast-iron frits. High temperature inorganic pigment including Red& yellow, blue, green, black Oxide etc, widely used in porcelain enamel, ceramics, glass, coating,painting etc. As an ISO9001:2008 certified manufacturer, we have strict quality control in the whole production process to guarantee the quality of products. We are supplying the best service for customer. 100% of Our goods are exporting to USA, Europe, Middle East, Southeast Asia, South America, & Africa. FAQ Q1. Are you factory or trading company ? We are a factory. Q2. Whats the MOQ ? Inorganic pigment MOQ is 25kg, enamel frit, RTU powder and electronic static powder MOQ=200kg. Q3. What is your principle for the samples ? We offer free samples if you are willing to pay the shipping cost. Q5. How about your delivery time? A: Generally, it will take 15 days after receiving your advance payment. Q6. What information should I let you know if I want to get a quotation? A: Your base material, your application area (best to send your finished product picture), the physical parameters you require(acid resistance, adherence, color, etc) the quantity you need. If possible, you can send me your samples and we customize for you. Q7.Why choose us? 1. Reaching a production capacity of 30,000 Tons/Year for Enamel frit, 10,000 Tons/Year for RTU & electronic static powder, 2,000 Tons/Year for Inorganic pigment. 2. 60% frits & pigment exported to US, Netherlands, Indonesia,Thiland, Vietanam, Korea, Chile etc 30 country. 3. Having over 30 technical experts of frits & pigment from domestic & overseas, focusing on technical development & product improvement. 4. Having complete quality control system, Strong technical supporting team is focusing on customer service in this world.