cross-linking activator particularly for fluoro elastomers used to achieve optimal compression set values at higher temperatures. It is normally used in combination with a fine particle size magnesium oxide. Packing Size: 9 kgs. Available Forms: Powder Technical Data Sheet Product Name : JC EG - 81 Function : Filler and Acid scavenger in FKM and other rubber and plastics. Technical Name : Calcium Hydroxide CAS No : 1305-62-0 Appearance : White Powder Calcium Hydroxide % ; 97.0 Min Sieve Residue (325 Mesh)% : 0.5 Max Moisture Content % : 1 Max Mode of action : JC EG - 81 is a cross-linking activator, particularly for fluoro elastomers used to achieve optimal compression set values at higher temperatures. It is normally used in combination with fine particle-size magnesium oxide. Processing : It is advisable to add JC EG - 81 together with the fillers or straight afterward, As JC EG - 81 is very hygroscopic therefore should, not be weighed until just before the incorporation in the mix Dosage : Normally 6-7 PHR JC EG - 81 in combination with 3PHR Magnesium oxide Packing : 9X1Kg EVA/PP Packet per box Storage : Stored in cool and dry atmosphere Advantages cross-linking activator particularly for fluoro elastomers used to achieve optimal compression set values at higher temperatures. It is normally used in combination with a fine particle size magnesium oxide.
All Types of Rubber compounds,requiring a quick incorporation in the mix and an excellent dispersion, avoid fly loss. Packing Size: 25 kgs. Available Forms: Powder Technical Data Sheet Product Name : JAYSULF - 54 Function : Curing agent for all natural and syntheticrubbers Appearance : Light Yellow Powder (low dust) Composition : 99% Sulfur (Micronized to uniform particle size of 325 mesh), 1% Additive for low dust Mode of action : Sulfur is a curing agent for all natural and synthetic rubbers, requiring quick incorporation in the mix and an excellent dispersion, the homogeneous dispersion in the rubber avoids the occurrence of localized over-cured zones. In this way, optimal activity of the effective substance is assured. Coating of Sulfur avoids fly loss helps in keeping the environment clean. Dosage : The dosage is the same as normal sulfur Material Properties Ref to : COA Advantages Coated Sulfur will give the folowing benefits Shorter mixing time Better dispersion Reduced batch-to-batch variation Reduced Fly loss (Environment friendly)
JC CB is a material produced by the incomplete combustion of coal and coal tar, vegetable matter, or petroleum products, including fuel oil, fluid catalytic cracking tar, and ethylene cracking in a limited supply of air. Carbon black is a form of paracrystalline carbon that has a high surface-area-to-volume ratio, albeit lower than that of activated carbon Packing Size: 20 kgs. Available Form: Paste Technical Data Sheet Product Name : JC CB-D3028 Carbon Black : 28% Advantages For easy handling , Dustfree environment ,aesthetic appeal such as uniform color tone or high black jetness , or blue undertone and conductivity to improve functionality of the end-use article.
Effective as a desiccant in both plastic as well as rubber applications. Packing Size: Customized as per requirement. Available Forms: Powder Technical Data Sheet Product Name: JC CaO - T Chemical Name : Calcium Oxide (treated with1% Organic Compound) Appearance : Fine white/off whitepowder. Solubility : Insoluble in water and soluble in mineral acids Special features : JC CaO T is made from soft stone with advance calcination technology which is resulting with high surface area, high activity and low Iron content. Special surface coating enhances the dispersion in rubber and plastic applications. There will be not any unintended reaction with humidity. Mode of action : calcium Oxide binds the moisture by the formation of calcium hydroxide, hence used as a desiccant to remove excessive moisture from rubber compounds CaO is preferably used in extrusion compounds which have to be cured continuously either in open air, like (fluid beds, salt baths) or in UHF curing process like (microwave units, and hot air channels), also used in the foamed compounds to improve the cell structure and surface finish of the end product. It can be effectively used in reprocessing of thermoplastic materials. Calcium Oxide : 94% Min. So. Gr. at 25oC 3.3 + 0.1 Bulk Density (gm/ml) : 0.65 + 0.1 Al2O3 : < 1.0 % SiO2 : < 2.0 % Fe2O3 : < 0.025 % Sieve residue 325 mesh < 1.0 % Sieve residue 200 mesh : Nil Mean Parcle Size Micron (D50%) : 4.5 - 6.5 Packing : Customize packing with EVA/PP Bag.(Normally 1 Kg Pack X20 Kg or 10 KgX2 Pack /Bag) Storage : Stored in cool and dry place, moisture strictly avoided Advantages CaOT is preferably used in extrusion compounds which have to be cured continuously either in open air, like (fluid beds, salt baths) or in UHF curing process like (micro wave units, and hot air channels), also used in the foamed compounds to improve the cell structure and surface finish of the end product. It can be effectively used in reprocessing of thermoplastic materials.
Effective as a desiccant in both plastic as well as rubber applications. Packing Size: Customized as per requirement. Available Forms: Powder Technical Data Sheet Product Name : JC CaO - T Chemical Name : Calcium Oxide (treated with1% Organic Compound) Appearance : Fine white/off whitepowder. Solubility : Insoluble in water and soluble in mineral acids Special features : JC CaO T is made from soft stone with advance calcination technology which is resulting with high surface area, high activity and low Iron content. Special surface coating enhances the dispersion in rubber and plastic applications. There will be not any unintended reaction with humidity. Mode of action : Calcium Oxide binds the moisture by the formation of calcium hydroxide, hence used as a desiccant to remove excessive moisture from rubber compounds CaO is preferably used in extrusion compounds which have to be cured continuously either in open air, like (fluid beds, salt baths) or in UHF curing process like (microwave units, and hot air channels), also used in the foamed compounds to improve the cell structure and surface finish of the end product. It can be effectively used in reprocessing of thermoplastic materials. Calcium Oxide : 94% Min. So. Gr. at 25oC : 3.3 + 0.1 Bulk Density (gm/ml) : 0.65 + 0.1 Al2O3 : < 1.0 % SiO2 : < 2.0 % Fe2O3 : < 0.025 % Sieve residue 325 mesh : < 1.0 % Sieve residue 200 mesh : Nil Mean Parcle Size Micron (D50%) : 4.5 - 6.5 Packing : Customize packing with EVA/PP Bag.(Normally 1 Kg Pack X20 Kg or 10 KgX2 Pack /Bag) Storage : Stored in cool and dry place, moisture strictly avoided Advantages CaOT is preferably used in extrusion compounds which have to be cured continuously either in open air, like (fluid beds, salt baths) or in UHF curing process like (micro wave units, and hot air channels), also used in the foamed compounds to improve the cell structure and surface finish of the end product. It can be effectively used in reprocessing of thermoplastic materials
JC CURE ZBP non Staining nitrosamine-free accelerator for EPDM and other diene elastomers, used as a Secondary accelerator in the efficient vulcanization of NR and other rubbers, such as IR, SBR, NBR, and IIR, EPDM. It is used in conjunction with sulfenamide, thiazole, thiuram and carbamate. It offers very good processing safety and does not bloom, for NR demonstrates excellent reversion and heat aging resistance. Packing Size: 25 kgs Available Form: Powder Technical Data Sheet Product Name : JC CURE ZBP Chemical Name : Zinc Dialkyldithiophosphate Composition : 70 % zinc dialkyldithiophosphate and 30% silica Appearance : White Powder Storage : Store in a cool dry place away from moisture and sunlight Stability : 24 Months from date of manufacture Advantages Due to excellent dispersion and solubility a constantly high quality is achieved. Cycle times can be shortened by high crosslinking rates. Faster extrusion speeds are also achievable. Lifetimes increased due to resistance to thermal ageing. Freedom from nitrosamines and poisonous substances, solve occupational health problems.
All Types of Rubber compounds,requiring a quick incorporation in the mix and an excellent dispersion, avoid fly loss. Packing Size: 25 kgs. Available Forms: Powder Technical Data Sheet Product Name : JAYSULF-96 Chemical Composition : 96%Sulphur, 2% MgCO3 and 2 % dispersing and wetting agents Appearance : Free Flowing Yellow Powder Product Description : 1305-62-0 Appearance : 96% Sulfur (Micronized to uniform particle size of 325 mesh) is conditioned with MgCO3 and dispersing and wetting agents to produce easy and uniform dispersion of Sulfur in natural rubber and synthetic rubber and especially in Nitrile Rubber.
OXI MAG HA is an effective scorch retardant and acts as an acid scavenger, curing agent and heat stabilizer in halogenated polymers like CR ,CIIR ,BIIR,FKM ,CSM CPE - Packing Size: 20 kgs/ 25 kgs. Available Forms: Powder Advantages Oximag HA a high purity active micronized magnesium oxide, has a very low level of chlorides and other volatiles, which does prevent any corrosion problems
Acts as lubricant, dispersing agent and mold releasing agent. It is effective against mill sticking. It improves extrusion properties of compounds. It reduces mold fouling and easy removal of articles from the mould. Packing Size: 25 kgs. Available Forms: Granules, Powder Technical Data Sheet Product Name : JC LUB PA - 45 Function : Processing promoter for compounds based on synthec rubber, especially FPM CO, ECO, ACM,and HNBR. Technical Name : Oleochemical Melting point : 58 + 7'C Solubility : Insoluble in water Acid Value : 8 Max Iodine Value : 1 Max Ash content : 0.3 Max Mode of action : Acts as lubricant, dispersing agent, and mold-releasing agent. It is effective against mill scking. It improves the extrusion properties of compounds. It reduces mold fouling and easy removal of articles from the mould.Mainly recommended for FPM (Fluoro elastomers) ACM and HNBR rubber, CO. ECO, EPDM, IIR (Butyl). In plastic : Recommended in Polycarbonates, thermoplastic Polyester (PPT, PET) and other engineering thermoplastics Dosage ; Typical dosage rate is 0.5 -2Phr Storage : Store in cool dry place away from moisture and sunlight The above information has been compiled from what we believe to be credible sources. To our knowledge the information is accurate and reliable, however, it is not guaranteed. It is the user's responsibility to determine the suitability of any JC EG 81 material in their application. The individual conditions of each customer are well outside of our control and we cannot be held liable for its functionality and use. As with all Chemical usage safety, precautions are highly recommended.
Gives excellent flow properties and highly effective lubricating properties. Improves dispersion of fillers and gives smooth surface in extruded and molded products. Works as internal lubricant improves flow gives lower die swell (improves dimensional stability) and benefits in filler incorporation. Acts as external lubricant aids in easy removal of molded parts in engineering plastics and thermoset process applications, also suitable for transparent plastics. Packing Size: 25 kgs. Available Forms: Granules, Powder Technical Data Sheet Product Name : JC LUB PE-72 Appearance : Creamish Powder Melting point : 78 + 7 C Solubility : Insoluble in water Mode of action : JC LUB PE-72 is a high molecular weight lubricant, suitable with PVC / PET / Masterbatch, polymers like Natural and Synthetic Rubbers. It is used as a process aid in extruding and molding rubber compounds, imparts excellent flow properties. It avoids mold fouling in Reclaim rubber and Butyl compounds. Processing : It is advisable to add JC LUB PE-72 added together with the filler Properties Gives excellent flow properties and highly effective lubricating properties. It improves the dispersion of fillers and provides a smooth surface in extruded and molded products. Work as an internal lubricant and benefits in filler incorporation. It acts as an external lubricant and aids in the easy removal of molded parts in engineering plastics and thermoset process applications, also suitable for transparent plastics. Dosage : 0.5 to 1.5 PHR or as per requirements Storage : Store in cool dry place away from moisture and sunlight
