Product’s name: Injection mold Keyword: Injection mold,blow molding, rotary mold, roto mold. Specification: We offer to make molds for injection molding, blow molding, rotary molding roto molding. We also undertake injection, blow or rotary molding works from Toys to Big bins or water tanks, floating docks, road barrier etc. We can do custom design plastic parts or components. Water Tanks ( Roto Molding process)
We supply balustrade and its related components like connectors, saddles, pipes end caps in SS201, SS304, SS316, SS316L. Pipes OD42.2mm*2mm. Also available other OD on request. Balustrade shape round, square any other custom designed shape. Height about 1060mm. Finish: satin, Glossy.
Product Description: We supply connector in SS201, SS304, SS316, SS316L suitable for pipes OD42.2mm*2mm. Also available other OD on requist. Connectors in round, square any other custom designed shape. Finish: satin, Glossy.
Supplier: Cosmetics bottle, cosmetics jar, makeup, essential oil, lipstick care bottle, lip gloss bottle, compact case, loose powder pot, spatulas, dosage, mascara bottle, perfume bottle, eyeliner bottle
Services: Provides expert product design / manufacture negotiation / production schedule/ quality control / logistics and shipping.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Material: PC off-Spec pellets Natural Category: PC Type: off-Spec pellets Grade/Color: Natural Quantity: 72 Loading weight: 24 Spec: PC off specs grade: PC-07NS pellets, medium-low flow , natural, heat stabilized, polycarbonate product with mold release designed for use in the general. MFI: around 7. Saudi Arabia Sabic Packing: Jumbo bags
Item Test condition Test Method Value Unit Density ISO 1183 0.944-0.955 g/cm3 MFR 190 C/2.16kg ISO 1133 0.03-0.07 g/10min Tensile strength at yield ISO 527-2 22 MPa Elongation at break ISO 527-2 >350 % ESCR F50,50 C,100% ASTM D-1693A 1000 h VICAT ASTM D-1525 126 C For extrusion packaging film, rope, woven bags, fishing nets, water pipes; injection of low-end commodity and housing, non-bearing load components, plastic box, turnover box; extrusion blow molding containers, hollow products, bottles.
Item Test condition Test Method Value Unit Density ISO 1183 0.944-0.955 g/cm3 MFR 190 C/2.16kg ISO 1133 0.03-0.07 g/10min Tensile strength at yield ISO 527-2 22 MPa Elongation at break ISO 527-2 >350 % ESCR F50,50 C,100% ASTM D-1693A 1000 h VICAT ASTM D-1525 126 C For extrusion packaging film, rope, woven bags, fishing nets, water pipes; injection of low-end commodity and housing, non-bearing load components, plastic box, turnover box; extrusion blow molding containers, hollow products, bottles.
We are INDONESIA Solid Wooden Panel Doors Maker ## All sizes made by demand ## Using Mix Hardwood or Meranti wood species ## Panels designed could be by request ## Natural finishing or PRIME WHITE FINISHED available ## Trial order minimum quantiry could be 400 pcs in 20ft container ## Idea price range from usd 50 /sheet - usd 70 / sheet ## Payment simple by negotiation by Bank transfer
Supplier: Medical cable, extrusion, cable, wire, connector, cable assembly, wire harness, pvc, hdpe, pp, ldpe, pcb, pcba, injection mold, injection molding, fixture, machining part, stamping part, tube, catheter, wire harness, release paper, release liner, flim, tape, silicone foam, sponge
Services: Export and shipping
