DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Epoxy Finish Paint is two-component, polyamide adduct cured, General Purpose Air drying Epoxy Coating. Its Excellent substitute to Enamel.
1.We use imported base paper from Germany. For solid color, base paper most 80 to 120GSM. For wood base paper is between 70-85 gsm 2. High quality water-base ink- Available over 200 shades in Solid colors and wood grains 3. With clear texture ,high Fidelity meeting international standards. 4. With smooth surface coating 5. Germproof, mould proof, antistatic and wear-resistance. 6. Green environmental protection and Odorlessness which Conforms to the GB18584-2001 standard requirement 7. Can be used for the hot press molding craft, the production efficiency is high. 8. Melamine paper takes shape easily, is widely used for the panel furniture and the decorative yarn. Product Specification: Width: 1230-1260mm or 1300-1800mm Length: 500-1000m For storing: Put it in room to a cool and dry place keep the temperature 20-25°C in room. The best humidity is: 50-60% We can also give you complete decorative solution with Matching Melamine Edge Banding, PU Paper. If you need just need Melamine/prelaminated boards either in MDF / Particle board we can also do so
We have range of patch fittings suitable for 8-15mm tempered glass doors. 1. Our patch fittings are suitable for 10mm, 12mm tempered glass doors 2. Bottom Patch fitting. 3. Top patch fitting. 4. Side Over panel. 5. Top center 6. Inserts available for most of the floor springs. 7. Aluminum, SS304. 8. Polished Stainless steel, Satin Stainless steel,aluminium oxsilver ,Aluminum Gold color.
Material: high carbon spring steel, spring steel, stainless steel, alloy steel Compression Spring, Extension Spring : Wire Diameter: 0.2-40.0mm Torsion spring wire diameter :0.2-35mm Surface Finish: black , Zinc, Nickel, silver, golden, tin, powder coating, shot pin Applications: Automotive, medical device, agricultural machinery ,electronics, toy, electric power distribution. Extension spring hook include Germany hook, British hook, Side hook We can customize special design of springs based on your requirement.
We are engaged in offering excellent quality Door Hinges to our valuable clients. 1. 4"x3"x3" with 2ball bearing 2. Material: q235 ,ss201,ss304, ss316 3. Size:101.6x76.2x3mm Color available: Brushed Chrome, Stain Nickel, Yellow Zinc, Antique Brass, Bright Brass, Polished Brass, Polished Chrome, Dull Brass, Brushed Zinc, Oil Rubbed Bronze, Antique Nickel, Antique Bronze, Primed Coating White, Primed Coating Black, Primed Coating Gray, Golden Finish.
Jumbo Bags : Name : Big bag/Bulk bag/Jumbo bag/FIBC/Super sack/Ton bag Raw Material : Polypropylene virgin material Color : White, blue, Beige, or whatever Printing : Onside or both sides in multi-colors,offset print color print Size : As the customers requirement Type of bag : U-panel,Circular,baffle Weave : 10x10,12x12,can be customized or as the customer requirement Denier : 700D to1000D Weights/m2 : 120gm to 240 gm or as the customers requirement Feature : Breathable and airy, anti-static, UV stabilization, reinforcement dust-proof, moisture- proof Sealing : Single/double fold saw bottom Top Filling : Top full open,top skirt,top filling spout Bottom : Flat bottom,discharge spout Saftey factory : From 3:1 to 6:1 Liner : coated or with liner bag for moisture proof Usage : sand,cement, chemical,mineral,sugar,food,flour,etc. Packing : 20pcs/bundle(bale), or as the customized MOQ : Above 1000pcs Delivery Time : 20-30 days after place an order Trade Term : FOB Payment Term : T/T
