1'two rollers are made from chilled cast iron, smooth surface is highly polished and scratch proof by cutting knife:high hardness and wear-resistant;
2'the roller is hollow structure, which is for adjusting the temperature of the rollers by
Steam or cooling water in term of different request;
3'nip adjustment mode:manual or electric;
4'main bearings:bearing or copper bush or nylon bush;
5'the machine is equipped with an overlaod protection device to prevent the major components from being damaged due to overloading.
6'the machine is also equipped with an emergency device. When an emergent accident happens, just draw the safety pull-rod, and the machine will stop immediately. It is safe and reliable.
7'the machine is equipped with scraper and wind-up unit, which can take the reclaimed rubber away from the wind-up roller
1'with ce and iso9001-2000 certificates
2'finest workmanship, high quality at reasonable price
3'good reputation widely
Main uses:
This rubber cutting machine is mainly used to cut the natural rubber, synthetic rubber, and other plastic materials, especially it is suitable to be installed near the rubber mixer to cut small piece of rubber.
with even fabric cord tension. It avoids sometimes tightening and loosening and improves the cutting accuracy.
3. The clamping cutting device uses festo rodless cylinder to drive the cuter rack to move forward and backward. It improves the working efficiency and omits the cutting speed improving device and chain drive system in xal-1450a. It is characterized by simple structure, quick running speed and smooth working without nosie.
4. The main drive cloth feeding device adopts the servo motor to drive the feed cloth roller directly. The feed cloth length, cutting times fixing programmes are controlled by plc. The feed cloth repeated accuracy is within ¡à1.0mm.
5. Pneumatic parts use smc products to improve the reliable work stability.
in operation; due to the different revolving speeds of the two relatively rotated rollers, the temperature of the working surface is also slightly different; then the raw materials on the roller surface gradually become soft along with the increasing temperature due to the heat conduction and fiction effect of the roller, stick to the roller surface and rotate with the roller.
When these raw materials enter into the gap on the working surface of two rollers, due to the small gap between the roller surfaces, and the revolving speeds on the two roller surfaces are different, the materials suffer from the strong extrusion, shear, and kneading action; due to the complex motion among the raw materials, the raw material produces a certain amount of friction heat in itself; in addition, the surface of the roller also has the conductive heat.
Due to the combined action between these internal factors and external conditions, the raw materials on the roller become softened and in mixed plasticization and molten state; in addition, the operator will constantly stir up the raw materials among the rollers, so that the raw materials can be mixed and plasticized uniformly. At the moment, the raw materials can be delivered to the calendar and rolled into the products.
1.The mixing chamber is of chilled structure with quick and better heating/cooling effects. The inner wall is coated with hard chrome for long service life..
2.Build-up welding of hard alloy for the two, three, four ridge top and two sides of the rotor, all the working surface are coated with hard chrome, good appearance and abrasive resistantce, the cooling/heating medium can pass through the hollow of the tangent linear type, mesh type, and synchronization type rotor.
3.Constant hydraulic pressure seal structure is used for the top of the rotor and the seal effect is good with long service time thanks to high pressure lubrication automatic alarm for used up of oil.
4.The upper bolt relieves the pressure automatically to protect the machine and for long service time if the machine work for too long time under overload condition.
5.The working surface of up and down bolts are coated with hard chrome, good appearance and abrasive resistance. The cooling/heating medium can pass through the inner hollow of down bolt.
6.A rotary oil cylinder is used for the discharge door, smooth running and accurate positioning.
7.Use two shafts put-out hard teeth reducer and gear coupling or "+" type universal joint, the transmission is smooth with high effciency, low noise level and long service life.
Quality: Stable, Good elasticity and Flexibility, self-life over 12 months
Application: Agricultural, Industrial, Electronic, Household, Tie Money, Flower, Hair, Package and Food, etc. Can be used widely as gifts, decorations, mechanical equipment, making gloves, etc.
