1'two rollers are made from chilled cast iron, smooth surface is highly polished and scratch proof by cutting knife:high hardness and wear-resistant;
2'the roller is hollow structure, which is for adjusting the temperature of the rollers by
Steam or cooling water in term of different request;
3'nip adjustment mode:manual or electric;
4'main bearings:bearing or copper bush or nylon bush;
5'the machine is equipped with an overlaod protection device to prevent the major components from being damaged due to overloading.
6'the machine is also equipped with an emergency device. When an emergent accident happens, just draw the safety pull-rod, and the machine will stop immediately. It is safe and reliable.
7'the machine is equipped with scraper and wind-up unit, which can take the reclaimed rubber away from the wind-up roller
We make rubber refining mill models from XKJ-450, XKJ-480, XKJ-610, roller length: 800mm, 1000mm, 1200mm Usage: For reclaimed rubber refining and mixing. Model: XKJ-450(510)X800 XKJ-450(510)X1000 XKJ-480(560)X800 XKJ-480(560)X1000 XKJ-480(560)X1200 XKJ-480(610)X800 XKJ-480(610)X1000 XKJ-480(610)X1200
-The rubber crusher belongs to reclaimed rubber machinery, it is mainly consists of machine body, transmission part, security device, roller temperature adjustment device, lubricating system and accident driving-stop device. -The former and the later roller is the main working parts of the machine, they working in an opposite direction via the motor and reduction gear's transmission within a certain speed ratio. -The roller's surface is made by chilled iron, hard, abrasion proof and long life time, the two sides of the roller is supported by sliding bearing, and use oil syringe for lubricant. The distance between two rollers can adjusted freely in a certain range. The machine is installed with security device, when working overloaded, the safe chip will break up to protect the main parts from damaged because of overloading. When the machine breaks down, once pulling the draw bar of the accident driving-stop device, the machine would stop rotating immediately. Both sides of the roller installed with rubber back plate. Parts of rollers are equipped with cooling device, using to adjust roll surface temperature.
SVR3L is made from latex harvested from our rubber plantation. It can meet customer strict requirement about some of technicalities such as: the PO, Color (Lovibond), SVR3L is made from latex harvested from our rubber plantation. It can meet customer strict requirement about some of technicalities such as: the PO, Color (Lovibond), Latex is preserved by ammonia or sodium sulfite. Then coagulated with formic acid, followed by shredding by passing through a rolling mill, washing system and hash.
SVR3L is made from latex harvested from our rubber plantation. It can meet customer's strict requirement about some of technicalities such as: the PO, Color (Lovibond), SVR3L is made from latex harvested from our rubber plantation. It can meet customerâ??s strict requirement about some of technicalities such as: the PO, Color (Lovibond), â?¦ Latex is preserved by ammonia or sodium sulfite. Then coagulated with formic acid, followed by shredding by passing through a rolling mill, washing system and hash. After the crumb rubber is dried, it will be compressed into blocks and packed in polyethylene bags
Continuous Operating Mixing Machine Function Mixing is one of the important parts in rubber product processing. So far, the most common technologies have been used are open mill mixing and internal mixer mixing, which are called non-continuous mixing. , We have designed the "screw mixing machine" in continuous leveling method and of high efficiency with the strong points as follow: It is efficient as it works long; It does not result in power wasting as there is no idle-running; It does not result in any working environmental impacts as the the transaction in the sealed main body of the machine; It reduces the cost and increase the profit in operation as less power and fewer workers are required compared to those for open mill or for internal mixer. It takes low labor intensity as there is only one worker needed in material feeding on the conveyor and qualified product is processed automatically. It is a new type of mixing machine which is highly recommended in rubber product processing.
TDF: Shredded tyres of size 5cm*5cm for the use as an alternative fuel in cement kilns. Fine TDF: Tyre chips of size 2cm * 2cm and below with vast majority of steel removed. This product is an extremely high quality alternative fuel with very high calorific value.
Supplier: Refining mill, rubber refining mill, cracker mill, rubber cracker mill, rubber crusher, mixing mill, roll mill, two roll mill, rubber mixing mill, rubber mill, rubber mixing machine
Supplier: Rubber mixing mill, rubber vulcanizing machine, rubber crusher mill, rubber refiner, rubber cutting machine, rubber sheet cooling machine, rubber extruder
Rubber mixing mills manufactured by our company have the models xk-160-xk-550(560), and we also manufacture refiner and gel breaker;classified by the perspectives of product standard and technical progress, the open mills manufactured by our company are coexisting with three generations of products: The traditional models of national reserved standards, that is, single output axis, which is driven by big and small gears and the differential motion of front and rear rollers are realized by speed ratio gears. National latest standards, that is, the output of reducer is double-axis output, and the roller is directly coupled by the universal coupled by the universal coupling. As for the double-axis output models have the disadvantages of high costs, we have developed the single-axis output open mills with a relatively lower cost, and such a model is an exclusive model of our company and is favored by the consumers