This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Smoke & co detectorHeat detector ntc thermal sensor tamper resistant pins for battery4 digits temperature led display shockproof design, suitable for vehicle usecan set maximum or minimum alarm temperature simultaneously test and hush button, auto resetreal ambient temperature correctable on-top battery compartment, easy for battery replacementauto reset /power off reset optional Execute criterion: en54-4, ul539, en14604, ul217 dustproof, mothproof and anti-white light ElectrovalveManipulator gas species: natural gas, lpg, man-made coal gas and other noncorrosive gaspower supply: 8vdc-16vdc 12vdc-26vdc valve body material: brass alloyoperation press: 1.6mpa material for sealing: nbr rubbervalve specification: 4 fen (1fen=1/3centimeter), 6fen, 1 inch, 1.25 inch, 1.5 inch test operating pressure: 25kpa torque: 10kg.Cm~30kg.Cm~40kg.Cm~50kg.Cm11069.540mm Anti-electromagnetic interference, no-spark design Alarm bellBreak glass manual call point size: 2", 3", 4", 6", 8", 9", 10", 12"rated voltage :12vdc or 24vdc / 220vac optional volume: over 105db/mconsumption: 10w working voltage : 12vdc/24vdc With waterproof cover manual call pointSiren with strobe
Operating voltage DC9~35V Alarm temperature 57 Static current 20uA Alarm current 35mA@DC12V;83m@DC24V Alarm output Remote LED indicator Installation Ceiling mounted Sensitivity 0.15dB/m(±0.03dB/M) Working environment -10~+50(â?¤95%RH No congelation) Dimension 100*46mm
Model NO SR-825PHS Operating voltage 3V lithium battery Static current 8uA Alarm current 35mA Alarm output Sound & Flash alarm Sound level 85dB/3m Installation Ceiling mounted Sensitivity 1.8%ft ±0.8%ft Working environment -10~+50,(95%RH No congelation) Dimension 95*41mm
Features  � High stability optical chamber � Circular LED indicator for 360° visibility � Network by current, NONC optional � Adapts CMOS with low power consumption � High adaptability to the ambient with dustproof, mothproof,  moistureproof, anti-white light and high EMI immunity � Input voltage: 10-35V DC � Orientation differences:
Conventional fire alarm smoke detector smoke probe sensor This device is photoeletronic detector uses a state-of-the-art optical sensing chamber. This smoke detector is compatible with all conventional fire alarm control panel Dual leds, two leds blink standby, provide 360dgree visibility With unique optical sensing chamber, engineered to sense smoke by a wide range of combustion sources. Unpolarized wire input to prevent the likelihood of wiring errors Specifications Operating voltage range: 9 to 28vdc volts non-polarized Standby current: 60µa @ 24 vdc Maximum alarm current (led on: ) 30ma @ 24 vdc Operating humidity range: 10% to 93% relative humidity, non-condensing Operating temperature range: 14°f to 122°f (-10°c to50°c) Adjustable sensitivity: 0.15ï½?0.3db/m Height: 2.2ë� (55 mm) installed in base Diameter: 4.0ë� (103 mm) Weight: 5.5 oz. (155 g)
Sd13 smoke alarm key features: * worry-free! 10-year sealed-in lithium battery * advanced photoelectric sensing technology offers high sensitivity * auto-check malfunction * low battery warning * manual test & auto-reset * dustproof, mothproof & anti-visible light * anti-rfi (20v/m-1ghz) Sd13 smoke alarm specifications: * sensor type: photoelectric * alarm sound: >85db (3m) * power supply: dc 3v lithium battery (included) * power supply life: 10 years * alarm current:
Place of Origin: Guangdong, China (Mainland) Brand Name: SUMRING Model Number: SR-820PHS COLOR: whitePower: 9V BatteryAlarm output: sound and flash alarm Photoelectric sensing technology: yes Sending frequency: N/ASensitivity: 2.06%ft±1.3%ft Sound level: 85dB/3m Installation: Wall or Ceiling mountedDimension: 128*38mm
Place of Origin: Guangdong, China (Mainland) Brand Name: SUMRING Model Number: SR-820PHS COLOR: whitePower: 9V BatteryAlarm output: sound and flash alarm Photoelectric sensing technology: yes Sending frequency: N/ASensitivity: 2.06%ft±1.3%ft Sound level: 85dB/3m Installation: Wall or Ceiling mountedDimension: 128*38mm
