APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Supplier: Foundry coke, pet coke, aggregate rock, cars, lpg, lng, fuel, diesel, health equipment, oil and gas equipment, steel (new or scrap), coir mats, rubber floor mats, polypropylene mat, pvc tufted, foundry coke, pet coke, aggregate rock, aggregate 3/4, aggregate 3/8,aggregate 3/16,wash sand, cars, lpg, lng, fuel, diesel, oil and gas equipment, steel (new or scrap), coffee, coffee beans, arabica coffee, dried coffee, robusta coffee, arabica and robusta coffee
Buyer: Foundry coke, pet coke, aggregate rock, aggregate 3/4, aggregate 3/8,aggregate 3/16,wash sand, cars, lpg, lng, fuel, diesel, oil and gas equipment, steel (new or scrap)
Product:Tube Fittings Brand:Renaissance Pipe Fitting Inc. Sizes:Refer the specification Condition:New Rating:4.3, based on 133 reviews price:Start from 5 USD Monel Tube Fittings, Inconel Tube Fittings, Hastelloy Tube Fittings, Copper Alloy Tube Fittings supplier. Stainless Steel tube fittings are manufactured and designed to meet the meticulous specifications necessary of industrial applications. RFP India tube fittings are generally used through the oil and gas, petro-chemical/chemical processing, pulp & paper, research laboratories, chemical processing, aerospace and defense, cryogenic and semiconductor, power generation, shipbuilding and heavy industrial industries. Available in several sizes and configurations, our SS tube fittings are made up of four parts including a body, back ferrule, front ferrule, and a nut. With fitting size range from 1/8 to 2 and with several choices in end patterns and connections, they are being rated to the highest working pressure of the suggested tubing.
Supplier: Tarpaulin, tarp, pe tarp, frp, grp, grating, pultruded, composite, frp rebar, panel tanks, pond liner, geomembrane, junction box, truck cover, boat cover, tent, camping, current transformers, indoor current transformers, outdoor transformers, switch gears, oil filled tank type transformers, wound primary type transformers, bar type transformers, window type transformers
1000 liter / 275 gallon repurposed rain tank. These are used & new tanks, food-grade tanks are comprised of a galvanized metal frame with a pallet (metal, plastic, or wood) and a plastic HDPE bottle. The rain tank has a 6, 8, or 12-inch top-fill cap and a 2-inch bottom butterfly or ball valve. The tanks may or may not include a plastic cap with a buttress or NPT thread for the bottom valve. If a valve cap is included, it can be drilled to accept our garden hose spigot assembly. A spigot assembly and 7/8 inch hole saw are not included. The dimensions are approximately 39 inches wide across the bottom valve, 47 inches deep, and 48 inches tall and the tanks weigh approximately 75 lbs empty. Previous contents may include olive oil, fish oil, organic fertilizer or beverage concentrates and some residue may still remain inside. The residue, if any, will only enrich the soil.
Key Parameters Capacity: 2/3/5/7.5 m3 (customizable). Operating pressure: 0.8/1.6 MPa (up to 3.5 Mpa). Design temperature: -196/20 (inner vessel), -20/50 (outer vessel). Gas flow rate: 80-100 Nm3/h. Content: LNG, LOX, LIN, LAR, LCO2, LN2O.... Insulation: High degree vacuum, fiberglass paper. DOER's Microbulk tank systems are designed for small-scale industrial / medical / residential applications, ensuring on-site continuous supply of gases (natural gas, oxygen, nitrogen, argon, carbon dioxide, nitrous oxide...), saving the trouble of frequent refilling/replacement of cylinders & dewars, reducing costs and increasing safety. Microbulk tanks have a very similar structure with vacuum insulated storage tanks, comprising double layers/shells (stainless steel & carbon steel), vacuum insulation, storing the gas in liquid form at very low temperature under low pressure, and suitable for multiple types of gases. Meanwhile, microbulk systems integrate a small air heated vaporizer to enable the output of gas directly. Suzhou Doer Gas & Chemical Equipment (DoerCryo) specializes in Atmospheric Cryogenic Storage Systems (Full Containment/Vacuum-insulated/MicroBulk Tanks for LNG, LOX, LIN, LAR, LCO2, LN2O, LC2H4...), VPSA Oxygen Generators/Plant, & Air Separation Units (ASU). We're ISO9001, 14001, 45001, ASME certified, having rich experience working with large engineering/energy enterprises, having been well received home and abroad.