Pup joint is cementing and fracturing equipment delivery High Pressure Fluid Control Products. Widely used in the acidic operating environment (excluding containing CO2, H2S sour gas operating environment) in the high-pressure discharge line, input line, a temporary flow line, well testing, and other high-voltage transmission lines on pipelines. Pup joint made of high strength steel, with a special toughening process. It uses Acme threaded connection, making it with the demolition convenient, fast, reliable connection, and reliable. Multiple seal design and high precision, to ensure the sealing performance of Pup joint. How to contact us?
Swivel loop Pup joint is cementing and fracturing equipment delivery High Pressure Fluid Control Products. Widely used in the acidic operating environment (excluding containing CO2, H2S sour gas operating environment) in the high-pressure discharge line, input line, a temporary flow line, well testing, and other high-voltage transmission lines on pipelines. Pup joint made of high strength steel, with a special toughening process. It uses Acme threaded connection, making it with the demolition convenient, fast, reliable connection, and reliable. Multiple seal design and high precision, to ensure the sealing performance of Pup joint. 1. The integral pup joint is union instead of screw connection on the top, which is more secure and reliable. 2. Easy and quick assembling and disassembling. 3. High strength and low weight. 4. Each technical parameters and performances of pup joints conform to standards of API Spec 6A and can be exchanged with like products internationally.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Product: Buttweld Fittings Brand: Renaissance Pipe Fitting Inc. Sizes: Refer to the specification Condition: New Rating:4.4, based on 172 reviews price: Start from 15 USD Buttweld Fittings and socketweld Fittings in Stainless steel and seamless, Pipe Caps, ANSI B16.9 Fittings, carbon steel, ANSI B16.28 Fittings, Equal and reducing crosses, MSS-SP-43 Fittings, Equal and reducing tees, caps, Lap joint Stub End supplier. RFP India is exporters of butt weld fittings and prepares them in a range of designs as per the provisions of our customers. There are many types of fittings such as Seamless, Welded, Fabricated, and more with Stainless Steel Butt Weld Fittings, Duplex Steel Butt Weld Fittings, Aluminium Butt Weld Fittings, Titanium Butt Weld Fittings, Carbon Butt Weld Fittings, and so on. Made up of by using high standard quality material along with quite sophisticated and high machines, our variety of butt weld fittings is quite recognized for its zero-defects, superior performance, and high quality. These butt weld pipe fittings are made up of by using high standard quality stainless steel, making these fittings anti-corrosive, making them nonaligned, and as well as making them survive intense temperature conditions. Sourced from reliable vendors, these fittings are highly acknowledged for their high tensile strength, durability, and accurate alloy composition. We offer butt weld fittings in several types like elbow, tee, return bends, reducer, stub-ends, cap, cross, insert, collar, and more.
Inconel 600 alloy is a nickel-chromium-iron-based solid-solution strengthened alloy, which has good high temperature corrosion resistance and oxidation resistance, excellent cold and hot processing and welding performance, and has satisfactory thermal strength and high plasticity below 700 �°C Here is the translation of the previous answer: The following are the national standard grades and specifications for Inconel 600: United States standard grade: UNS N06600 Specifications: AMS 5540: Seamless and welded nickel alloy plate, sheet, and strip with good oxidation and high-temperature creep properties at 800�°F (427�°C). ASTM B166: Standard specification for nickel-chromium-iron alloys, seamless and welded rod, bar, and wire. ASME SB-166: Same as above. European standard grade: NiCr15Fe (2.4816) Specifications: EN 10095: Technical delivery conditions for hot rolled and forged stainless steel and heat-resisting steel and hot finished structural hollow sections. EN 10002-1: Method of tensile testing of metals. EN 10002-5: Method of compressive testing of metallic materials. Japanese standard grade: NCF 600 Specifications: JIS G4902: Standard specification for seamless and welded nickel alloy pipes and tubes. JIS G4903: Standard specification for seamless and welded nickel alloy pipes and tubes. Chinese standard grade: GH3600 Specifications: GB/T 14992: Standard specification for seamless and welded nickel alloy tubes and pipes. GB/T 14995: Standard specification for nickel alloy forgings. GB/T 12771: Standard specification for seamless and welded steel pipes for hydraulic transmission. These specifications define the chemical composition, physical properties, processing, and testing requirements of Inconel 600 materials to ensure their quality and performance meet the standards. We can provide the following the form:Inconel600 alloy coil; Inconel600 alloy strip;Inconel600 alloy plate; Inconel600 alloy sheets; inconel600 alloy tube; Inconel600 alloy pipe; Inconel600 alloy flat; Inconel600 alloy bar GB:00Cr21Ni57Mo8Nb5TiA1;JIS:NCF725:UNS:N07725;W.Nr:2.4668 Used for pipe fittings, joints and bearings in acid-resistant equipment. It is also widely used in marine ship equipment
ProductASME 165 lapjoint flanges BrandRenaissance Pipe Fitting Inc SizesRefer the specification ConditionNew Rating42 based on 26 reviews priceStart from 20 USD RFP India is a determined manufacturer of high quality of industrial lap joint flanges in India It is very much similar to slipon flange where it is having a radius at the junction of the bore and flange face that is for to create a lap stub end In the meantime the look on the stub end forms out by means of the gasket face on the flange Lap Joint flanges are being used in applications where parts of the piping systems need to be taking away from each other quickly and easily for inspection and replacement These lap joint flanges are being provided in fullscale range and are extensively used at all the pressures RANGE 15 NB to 60 1500NB in 150 LBS 300 LBS 600 LBS 900 LBS 1500 LBS 2500 LBS ASA 150 ASA 300 PN 6101625 4064100160 ETC available with NACE MR 0175 SIZE 15NB to 60 1500NB CLASS PRESSURE Class Pressure 150 300 600 900 1500 2500 PN6 PN10 PN16 PN25 PN40 PN64 DIMENSION B165 BS4504 EN1092 B1636 B1647 B1648 MSS SP44 STD STD ANSI Flanges ASME Flanges DIN Flanges EN Flanges BS Flanges API JIS NACE etc FEATURES Dimensional accuracy Corrosion resistance High efficiency Excellent finish Durable Stainless Steel Lap Joint Flanges Standard ASTM ASME ASA 182 Grade F 304 304L 304H 309S 309H 310S 310H 316 316TI 316H 316L 316LN 317 317L 321 321H 347 347H 904L Duplex Steel Lap Joint Flanges Standard ASTM ASME ASA 182 Grade F 44 F 45 F51 F 53 F 55 F 60 F 61 Aluminium Lap Joint Flanges Standard ASTM B247 B361 Grade 2024 6061 6063 6101 7075 Titanium Lap Joint Flanges Standard ASTM B381 Grade Grade 1 Grade 2 Grade 4 Grade 5 Grade 6 Grade 7 Grade 9 Grade 19 Grade 23 Carbon Steel Lap Joint Flanges Standard ASTM A 105A694 A350 LF3A350 LF2 Grade F42465256606570 Low Temperature Carbon Steel Lap Joint Flanges Standard ASTM A 350 LF2 A350 LF3 Alloy Steel Lap Joint Flanges Standard ASTM A182 Grade F1F5F9F11F22F91 Copper Alloy Lap Joint Flanges Standard ASTM ASME SB 61 62 151 152 Grade UNS NO C 70600 CU NI 9010 C 71500 CU NI 7030 C 71640 Nickel Alloy Lap Joint Flanges Standard ASTM ASME SB 564 160 472 Nickel 200 UNS N02200   Nickel 201 UNS N02201   Monel 400 UNS N04400 Monel K500 UNS N05500   Inconel K600 UNS N06600   Inconel 601 UNS N06601 Inconel 625 UNS N06625   Inconel 800 UNS N08800   Inconel 800H UNS N08810 Inconel 825 UNS N08825   Hastelloy C276 UNS N10276   Alloy 20 UNS N08020 Test Certificate Manufacturer Test Certificate as per EN 10204 31 nbsp Types Of Lap Joint Flanges SS 310 310S Lap Joint Flanges Duplex Steel UNS S31803 Lap Joint Flanges Stainless Steel 304 304L Lap Joint Flanges Duplex Steel Lap Joint Flanges Stainless Steel 316 316L Lap Joint Flanges Duplex Steel UNS S32205 Lap Joint Flanges Stailess Steel 321 321H Lap Joint Flanges Super Duplex UNS S327
Inconel Alloy 725 (UNS N07725) is a nickel chromium molybdenum niobium alloy with high corrosion resistance and age hardening to very high strength. Its composition is similar to Inconel 625 alloy. Inconel 625 is an alloy widely used in various corrosive environments. Its strength can be improved by cold work hardening and has been used for small bolts. Inconel 725 alloy basically has the same corrosion resistance as Inconel 625 alloy, but Inconel 725 alloy is an alloy that is age-strengthened by a heat treatment process. Since the stress of Inconel 725 alloy is through heat treatment instead of cold working, the plasticity and toughness are still high, and it is suitable for making high-strength, high-corrosion-resistant parts. Here are the common national standard designations of Inconel 725: US standard designations: UNS N07725, AMS 5660, AMS 5832, AMS 5772, AMS 5796, AMS 5581, ASTM B805, ASTM B805, ASTM B805. European standard designations: EN 2.4668, EN 10269, EN 10272, EN 10216-5, EN 10250-4, EN 10263-4, EN 10297-2, EN 10302, EN 10312, EN 12266-1, EN 12560-6, EN 13480-3, EN 13480-5, EN 13544-2, EN 1592-4. German standard designations: DIN NiCr22Mo9Nb, DIN 2.4627, DIN 17742, DIN 17744, DIN 17752, DIN 17754, DIN 17751. Japanese standard designations: JIS NCF725, JIS G4902, JIS G4941, JIS G5502, JIS G5122. Chinese standard designations: GB/T UNS N07725, GB/T 14992, GB/T 15001, GB/T 15003, GB/T 15004, GB/T 21833. We can provide the following the form:Inconel725 alloy coil; Inconel725 alloy strip;Inconel725 alloy plate; Inconel725 alloy sheets; Inconel725 alloy tube; Inconel725 alloy pipe; Inconel725 alloy flat; Inconel725 alloy bar Used for pipe fittings, joints and bearings in acid-resistant equipment. It is also widely used in marine ship equipment; GB:00Cr21Ni57Mo8Nb5TiA1;JIS:NCF725;UNS:N07725;W.Nr 2.4668
ProductASME 165 ring joint flanges BrandRenaissance Pipe Fitting Inc SizesRefer the specification ConditionNew Rating45 based on 28 reviews priceStart from 20 USD RFP India is one of the foremost Supplier and Manufacturers that offers high quality of Ring Joint Flanges These flanges are time and again used through their most significant benefit which is it can be used for unanticipated circumstances and in very changeable areas where welding is unsafe With dissimilar materials like Stainless steel Alloy steel and Carbon steel RFP India offer dissimilar types of Ring Joint Flanges such as SlipOn Threaded and Welding Neck amongst others Meanwhile these types of Flanges are also accessible in different sizes specification grades and thickness as per the needs of clients RANGE 15 NB to 60 1500NB in 150 LBS 300 LBS 600 LBS 900 LBS 1500 LBS 2500 LBS ASA 150 ASA 300 PN 6101625 4064100160 ETC available with NACE MR 0175 SIZE 15NB to 60 1500NB CLASS PRESSURE Class Pressure 150 300 600 900 1500 2500 PN6 PN10 PN16 PN25 PN40 PN64 DIMENSION B165 BS4504 EN1092 B1636 B1647 B1648 MSS SP44 STD STD ANSI Flanges ASME Flanges DIN Flanges EN Flanges BS Flanges API JIS NACE etc FEATURES Dimensional accuracy Corrosion resistance High efficiency Excellent finish Durable Stainless Steel Ring Joint Flanges Standard ASTM ASME ASA 182 Grade F 304 304L 304H 309S 309H 310S 310H 316 316TI 316H 316L 316LN 317 317L 321 321H 347 347H 904L Duplex Steel Ring Joint Flanges Standard ASTM ASME ASA 182 Grade F 44 F 45 F51 F 53 F 55 F 60 F 61 Aluminium Ring Joint Flanges Standard ASTM B247 B361 Grade 2024 6061 6063 6101 7075 Titanium Ring Joint Flanges Standard ASTM B381 Grade Grade 1 Grade 2 Grade 4 Grade 5 Grade 6 Grade 7 Grade 9 Grade 19 Grade 23 Carbon Steel Ring Joint Flanges Standard ASTM A 105A694 A350 LF3A350 LF2 Grade F42465256606570 Low Temperature Carbon Steel Ring Joint Flanges Standard ASTM A 350 LF2 A350 LF3 Alloy Steel Ring Joint Flanges Standard ASTM A182 Grade F1F5F9F11F22F91 Copper Alloy Ring Joint Flanges Standard ASTM ASME SB 61 62 151 152 Grade UNS NO C 70600 CU NI 9010 C 71500 CU NI 7030 C 71640 Nickel Alloy Ring Joint Flanges Standard ASTM ASME SB 564 160 472 Nickel 200 UNS N02200   Nickel 201 UNS N02201   Monel 400 UNS N04400 Monel K500 UNS N05500   Inconel K600 UNS N06600   Inconel 601 UNS N06601 Inconel 625 UNS N06625   Inconel 800 UNS N08800   Inconel 800H UNS N08810 Inconel 825 UNS N08825   Hastelloy C276 UNS N10276   Alloy 20 UNS N08020 Test Certificate Manufacturer Test Certificate as per EN 10204 31 nbsp Types Of Ring Joint Flanges SS 310 310S Ring Joint Flanges Duplex Steel UNS S31803 Ring Joint Flanges Stainless Steel 304 304L Ring Joint Flanges Duplex Steel Ring Joint Flanges Stainless Steel 316 316L Ring Joint Flanges Duplex Steel UNS S32205 Ring Joint Flanges Stailess Steel 321 321H Ring Joint Flanges
ProductASME 165 plate flanges BrandRenaissance Pipe Fitting Inc SizesRefer the specification ConditionNew Rating47 based on 52 reviews priceStart from 20 USD RFP India is a wellknown manufacturer and supplier of Plate Flanges in the steel market industry worldwide Plate flanges are most commonly used in fuel and water pipelines where two flange plates are locked up together with a gasket in the central point of them The flange plate will now have bolt holes all in the region of outer limits and will be used to make joints tees and junctions Meanwhile there are several benefits of Plate Flanges such as it is free from any shortcomings has an unmitigated service life has finer grain establishment as measured up to forged or cast items reduction of the customary maintenance expenditures and so on RANGE 15 NB to 60 1500NB in 150 LBS 300 LBS 600 LBS 900 LBS 1500 LBS 2500 LBS ASA 150 ASA 300 PN 6101625 4064100160 ETC available with NACE MR 0175 SIZE 15NB to 60 1500NB CLASS PRESSURE Class Pressure 150 300 600 900 1500 2500 PN6 PN10 PN16 PN25 PN40 PN64 DIMENSION B165 BS4504 EN1092 B1636 B1647 B1648 MSS SP44 STD STD ANSI Flanges ASME Flanges DIN Flanges EN Flanges BS Flanges API JIS NACE etc FEATURES Dimensional accuracy Corrosion resistance High efficiency Excellent finish Durable Stainless Steel Plate Flanges Standard ASTM ASME ASA 182 Grade F 304 304L 304H 309S 309H 310S 310H 316 316TI 316H 316L 316LN 317 317L 321 321H 347 347H 904L Duplex Steel Plate Flanges Standard ASTM ASME ASA 182 Grade F 44 F 45 F51 F 53 F 55 F 60 F 61 Aluminium Plate Flanges Standard ASTM B247 B361 Grade 2024 6061 6063 6101 7075 Titanium Plate Flanges Standard ASTM B381 Grade Grade 1 Grade 2 Grade 4 Grade 5 Grade 6 Grade 7 Grade 9 Grade 19 Grade 23 Carbon Steel Plate Flanges Standard ASTM A 105A694 A350 LF3A350 LF2 Grade F42465256606570 Low Temperature Carbon Steel Plate Flanges Standard ASTM A 350 LF2 A350 LF3 Alloy Steel Plate Flanges Standard ASTM A182 Grade F1F5F9F11F22F91 Copper Alloy Plate Flanges Standard ASTM ASME SB 61 62 151 152 Grade UNS NO C 70600 CU NI 9010 C 71500 CU NI 7030 C 71640 Nickel Alloy Plate Flanges Standard ASTM ASME SB 564 160 472 Nickel 200 UNS N02200   Nickel 201 UNS N02201   Monel 400 UNS N04400 Monel K500 UNS N05500   Inconel K600 UNS N06600   Inconel 601 UNS N06601 Inconel 625 UNS N06625   Inconel 800 UNS N08800   Inconel 800H UNS N08810 Inconel 825 UNS N08825   Hastelloy C276 UNS N10276   Alloy 20 UNS N08020 Test Certificate Manufacturer Test Certificate as per EN 10204 31 nbsp Types Of Plate Flanges SS 310 310S Plate Flanges Duplex Steel UNS S31803 Plate Flanges Stainless Steel 304 304L Plate Flanges Duplex Steel Plate Flanges Stainless Steel 316 316L Plate Flanges Duplex Steel UNS S32205 Plate Flanges Stailess Steel 321 321H Plate Flanges Super Duplex UNS S32750 Plate Flanges Monel 400 Plate F
Specification: 1).size: 2'', 3'', 4'' 2).working pressure:6000-20000psi(42Mpa-140Mpa) 3).working temperature: -29°C~121°C. 4).application enrvironment: standard or H2S 5).Standard: API standard Introduction: 1. Our swivel joints, with integral ball bearing, are manufactured on the basis of technologies from FMC, USA. 2. Various models of swivel joints and their repair kits are available, suitable for normal or low temperature, or H2S environments, with sizes ranging from 2" to 4" and rated WP ranging from 6000-20000psi(42Mpa-140Mpa). 3. We can supply long and short radius swivel joints. Long radius swivel joints can minimizefluid shock, and has better performance of resistance for scouring and erosion. We also need to use short radius swivel joints for low pressure operation due to limited installation space. 4. Patterns of swivel joint are made in NC machine tools, with even wall thickness and longer service life. Wall thickness difference of inner and outer arcs can meet FMC standard.The three-ball-race design can bear heavy load stably, and ensure less vibration with variable load. 5. All sizes of swivel joints can be interchanged with FMC equivalent products used in cementing and fracturing equipment. 6. Sealing parts made of synthetic rubber with release hole are fitted with blowout preventing metal ring. When sealing parts leak, pressure will be automatically relieved. Safety performance is enhanced. 7. Usually good lubrication can ensure that swivel joints work normally without much maintenance.
Specification: 1).Size: 2'', 3'', 4'' 2).Working pressure:6000-20000psi(42mpa-140mpa) 3).Working temperature: -29â°c~121â°c. 4).Application enrvironment: standard or h2s 5).Standard: api standard Introduction: 1. Our swivel joints, with integral ball bearing, are manufactured on the basis of technologies from fmc, usa. 2. Various models of swivel joints and their repair kits are available, suitable for normal or low temperature, or h2s environments, with sizes ranging from 2" to 4" and rated wp ranging from 6000-20000psi(42mpa-140mpa). 3. We can supply long and short radius swivel joints. Long radius swivel joints can minimizefluid shock, and has better performance of resistance for scouring and erosion. We also need to use short radius swivel joints for low pressure operation due to limited installation space. 4. Patterns of swivel joint are made in nc machine tools, with even wall thickness and longer service life. Wall thickness difference of inner and outer arcs can meet fmc standard.The three-ball-race design can bear heavy load stably, and ensure less vibration with variable load. 5. All sizes of swivel joints can be interchanged with fmc equivalent products used in cementing and fracturing equipment. 6. Sealing parts made of synthetic rubber with release hole are fitted with blowout preventing metal ring. When sealing parts leak, pressure will be automatically relieved. Safety performance is enhanced. 7. Usually good lubrication can ensure that swivel joints work normally without much maintenance.
Specification: 1).size: 2'', 3'', 4'' 2).working pressure:6000-20000psi(42Mpa-140Mpa) 3).working temperature: -29°C~121°C. 4).application enrvironment: standard or H2S 5).Standard: API standard Introduction: 1. Our swivel joints, with integral ball bearing, are manufactured on the basis of technologies from FMC, USA. 2. Various models of swivel joints and their repair kits are available, suitable for normal or low temperature, or H2S environments, with sizes ranging from 2" to 4" and rated WP ranging from 6000-20000psi(42Mpa-140Mpa). 3. We can supply long and short radius swivel joints. Long radius swivel joints can minimizefluid shock, and has better performance of resistance for scouring and erosion. We also need to use short radius swivel joints for low pressure operation due to limited installation space. 4. Patterns of swivel joint are made in NC machine tools, with even wall thickness and longer service life. Wall thickness difference of inner and outer arcs can meet FMC standard.The three-ball-race design can bear heavy load stably, and ensure less vibration with variable load. 5. All sizes of swivel joints can be interchanged with FMC equivalent products used in cementing and fracturing equipment. 6. Sealing parts made of synthetic rubber with release hole are fitted with blowout preventing metal ring. When sealing parts leak, pressure will be automatically relieved. Safety performance is enhanced. 7. Usually good lubrication can ensure that swivel joints work normally without much maintenance.
Tape Width >100 mm Tape Length >50 m Color Silver Use Bag Sealing Adhesive Acrylic Material Aluminium Foil Aluminum Foil Tapes are coated with acrylic or rubber adhesive and available with or without release paper. This foil tapes are available with 25 mic-100 mic thickness. Features: Shiny silver, U.V. resistance Flame, moisture and many chemical barrier Good for harsh Long term outdoor application It has hot & cold insulation property Usage: Widely used in tubes and lead jointing for air conditioner, refrigerator and water heaters. For wrapping on pipes, engines and wires as a heat & water resistance. Used as a static ground application.
We specialise in providing a comprehensive range of auto parts & motor parts. Our commitment is to offer high-quality products that ensure optimal performance, safety, and reliability for all types of vehicles Here's a list of some of the auto parts we provide: 1. Engine Components: - Spark plugs - Oil filters - Air filters - Belts and hoses - Engine mounts - Timing belts/chains - Pistons & Rings 2. Braking System Parts: - Brake pads - Brake rotors/discs - Brake calipers - Brake lines - Master cylinders - Brake fluid 3. Suspension and Steering Parts: - Shock absorbers/struts - Control arms - Tie rod ends - Ball joints - Steering racks - Power steering pumps 4. Electrical Components: - Batteries - Alternators - Starters - Ignition coils - Wiring harnesses - Sensors (Oxygen sensors, ABS sensors, etc.) 5. Cooling System Parts: - Radiators - Water pumps - Thermostats - Radiator hoses - Cooling fans - Heater cores 6. Exhaust System Parts: - Exhaust manifolds - Catalytic converters - Mufflers - Exhaust pipes - Oxygen sensors - Gaskets and seals 7. **Transmission and Drivetrain Parts:** - Transmission fluid - Clutch kits - CV joints - Axles - Transmission mounts - Differential parts 8. Interior and Exterior Accessories: - Headlights - Tail lights - Mirrors - Wiper blades - Floor mats - Seat covers 9. Performance Upgrades: - Cold air intakes - Exhaust headers - Performance chips/tuners - Suspension lift kits - Turbochargers - High-performance brakes 10. Maintenance and Service Items: - Oil and lubricants - Filters (air, oil, fuel) - Sealants and adhesives - Cleaning and detailing products - Tools and equipment - Diagnostic scanners Our goal is to provide top-notch products, exceptional customer service, and competitive prices to ensure your satisfaction.
321 stainless steel is an austenitic stainless steel that contains titanium as a stabilizing element. This element helps to prevent chromium carbide precipitation, which can occur during high-temperature service, making it ideal for use in high-temperature applications. Some of the key properties of 321 stainless steel include: High-temperature resistance: 321 can withstand high temperatures up to 870�°C (1600�°F) without losing its strength or corrosion resistance properties, making it ideal for use in applications such as furnace parts and exhaust systems. Corrosion resistance: 321 offers excellent resistance to corrosion, including aqueous corrosion and stress corrosion cracking. Strength and toughness: 321 has good strength and toughness, making it suitable for use in demanding applications. Fabricability: 321 is easily formable using standard methods, and can be welded using common welding techniques. Some of the common applications for 321 stainless steel include: Exhaust systems in automobiles, aircraft, and industrial equipment High-temperature furnace parts, such as burners and heating elements Chemical processing equipment Jet engine parts Heat exchangers Overall, 321 stainless steel is a highly reliable and versatile material that is well-suited for use in high-temperature applications where superior corrosion resistance and strength are required. The following are some of the commonly used international standards for 321 stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276/A276M: Standard Specification for Stainless Steel Bars and Shapes EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10095: Heat resisting steels and nickel alloys JIS G4304: Hot-rolled stainless steel plate, sheet and strip JIS G4305: Cold-rolled stainless steel plate, sheet and strip GB/T 4237: Hot rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip We can provide the following form:321 stainless steel coil; 321 stainless stee strip;321 stainless stee plate; 321 stainless steel sheets; 321 stainless steel tubes; 321 stainless steel pipe; 321 stainless steel flat; 321 stainless steel bar Applied to open-air machines, heat-resistant parts of building materials and parts with difficulty in heat treatment in chemical, coal and petroleum industries that require high resistance to intergranular corrosion 1. Petroleum waste gas combustion pipeline 2. Engine exhaust pipe 3. Boiler shell, heat exchanger, heating furnace parts 4. Silencer parts for diesel engines 5. Boiler pressure vessel 6. Chemical transport vehicle 7. Expansion joints 8. Spiral welded pipes for furnace pipes and dryers
Description: A pup joint is a casing or tubing of length shorter than Range 1 with the same thread connection, used to adjust the length of tubular strings to its exact requirement.
Description Swivel joint is a kind of high pressure fluid control products, which is commonly applied to cementing and fracturing equipment. Swivel joint is a kind of high pressure fluid control products, which is commonly applied to cementing and fracturing equipment. It is used to change the pipeline connection direction, to make it more convenient and easier to connect the pipe fittings. It is widely used in acid working environment, to connect the high pressure discharge pipe, suction pipe, temporary flow pipeline, well test line and high pressure transmission line.
(1)Standard: API 5CT (2)Size: 2 3/8"-13 3/8" (3)Grade: J55,K55,L80,N80.P110 (4Type:STC,LTC,BTC,EUE,NUE surface treatment:coating. Protection of Thread:Thread protector Packing: in bundle,by wooden pallet or by steel strip or by the requirements of customer. Pup Joints are used to adjust the height of full length tubing or casing strings. They are also used to adjust the depth of downhole tools. Pup Joint sets are available in: Integral Premium Thread Box-by-Pin Pin-by-Pin with couplings boxed separately Pin-by-Pin with couplings hand tight Pin-by-Coupling Box Flush joint connections Quality is our main competitive advantage The requirements and expectations of our customers must be satisfied Quality management is integrated into all our business processes Management is responsible and accountable for quality performance Quality performance must be assured throughout the supply chain system Excellence in quality management is necessary for successful business -