High Volume Air Sampler for PM2.5 Global's line of extremely reliable and durable samplers created for capturing particulate matter and gaseous contaminants in ambient air are known as High Volume Air Samplers (HVAS). The High Volume Air Sampler (HVAS) is a piece of equipment used to sample huge amounts of ambient air in order to filter out the particulate matter it contains. Finely divided solids or liquids that are spread in the air from natural sources, industrial operations, or both are referred to as particulate matter. To stop collecting of particles larger than a certain size, a Size Selective Inlet (SSI) is used as a pre-filter. Size Selective Inlet (SSI) PM 2.5 only allows particles with an AED 2.5 micron diameter to enter the collection medium; particles larger than 2.5 microns are not allowed. Features of the physical design: High Volume Air Samplers, such as the PEV-HVS and PEM- RDS series, PM2.5HVS, are made up of a large blower, a filter to catch suspended particles, and a way to gauge the flow rate. Through the side apertures of the SSI, suspended airborne particles are sampled at sampling rates ranging from 1.1 to 1.6 m3/min and collected on a 203 x 254 mm filter paper. Important Features: Electronic Control Module with a Microprocessor; 32-character LCD Module with alphanumeric characters; Electronic Timer Cumulative Totalizer. Continuous Duty Blowers; Settable Delay & Sampling Time The exhaust orifice plate meets with USEPA standards. An optional gaseous sampling attachment for all models. By replacing the gable roof with SSI, it can be transformed into a PM10 sampler. Unique Characteristics: Free flow without resistance at 1.1 to 1.7 Cu m/min flow rate. Particle Size: Depending on the filter being used, down to 0.3 micron. Filter holder made to fit any standard 8 X 10 (20.3 X 25.4 cm) size filter sheet. The GF/A filter is advised for general use, and EPM 2000 for specialised research. Time Totalizer: Record the running time in hours from 0 to 99999.99 hours for sampling time: Automatic Sampling: A 24 hour programmable timer that automatically turns the device on or off after the preset intervals can be easily set. 220 volts, 5 amps, single phase AC power requirements. Rotameter flow rate is measured with a plastic body flow metre with a 2% FSD accuracy between 0 and 3 lpm.
ECTFE Coating Grade Resin 1.Product introduction As a resin, ethylene chlorotrifluoroethylene is a very pure fluorine copolymer, which not only has excellent mechanical properties, good weather resistance and chemical resistance common to fluorine-containing resins, but also has excellent light transmittance and hardly absorbs visible light and ultraviolet light. In addition, because it contains chlorine atoms, the moisture permeability of all fluorine resins is relatively low, which can prevent many liquids and gases from penetrating, and is beneficial to the anticorrosion and rust prevention of the protected substrate. 2.Technical Parameter Item Test Method Unit Value Density ASTM D792 g/cm3 1.66~1.68 Grain Size ASTM D1921 um 40~80 Melting Point ASTM D3418 �ºC 215~225 Melt Index ASTM D1238 g/10min (275�ºC,2.16kg) 8~15 3.Mark, Packing, Storage & Transportation 3.1 Mark The packing bags (boxes) of this product should be clearly marked with firm company name, product name, batch number, brand number (specification number), net content, etc. 3.2 Package This product is packed in paper barrels (lined with polyethylene plastic bags) with a net content of (20 �± 0.2) kg per barrel. Each barrel shall be provided with a product certificate, including: company name, product name, batch number, brand (specification number), net content and production date, etc. In case of special packaging, the supplier and the Demander shall negotiate separately. 3.3 Storage This product should be stored in a clean, cool and dry place to prevent rain, sunshine, moisture, dust and other impurities. 3.4 Transportation This product is transported according to non-dangerous goods. Moisture and severe vibration should be avoided during transportation. 4.Main Application 4.1 ECTFE coating grade resin is white powder, which has excellent chemical corrosion resistance, excellent barrier performance to various corrosive gases and excellent high and low temperature resistance. 4.2 The electrostatic spraying method can be used for coating protection of reactors, pipelines, storage and irrigation, mixers and other containers in the chemical and semiconductor fields, thus delaying the service life of the equipment.
1.Product Introduction PVDF resin has weather resistance, light retention, color retention, chemical corrosion resistance, excellent post-processing, high temperature resistance, high cost performance, easy maintenance and high decoration. 2.Technical Parameter Item Test Method Unit Index Apparent Density GB/T6373 g/ml 0.28~0.40 Water Content GB/T6284 % 0.2 Purity % 99.5 Scattered Fineness 30min) GB/T1724 m 30 Grinding Fineness(5min) GB/T1724 m 30 Stomer Viscosity GB/T9269 KU 70 ±10 Melting Point ASTM D3418 156~165 Thermal Decomposition TGA,1%wt.Loss Air 390 Melt Flow Rate ASTM  D1238 230 10kg g/min 0~3.0 3.Mark, Package, Storage & Transportation 3.1 Mark The packaging barrel of this product shall be provided with firm and clear identification, indicating the company name, product name, batch number, brand (specification number), net content, etc. 3.2 Package The product is packed in paper drums (lined with double-layer polyethylene plastic bags), and the net content of each barrel is (25 ± 0.2) kg; Each barrel shall be provided with product certificate, including company name, product name, batch number, brand (specification number), net content, production date, etc. If special packaging is required, the supplier and the buyer shall negotiate separately. 3.3 Storage This product should be stored in a clean, cool and dry place to prevent rain, sunlight, moisture, dust and other impurities. 3.4 Transportation This product is transported as non dangerous goods. Avoid moisture and violent vibration during transportation. 4.Main Application PVDF resin mixed with acrylic resin and additives can form baking PVDF fluorocarbon coating with superior performance. The coating can be used for aluminum workpieces and aluminum curtain walls, such as plates, profiles, window frames and door frames, with a service life of more than 20 years. The base material must be pretreated before coating. Generally, the construction process of two coating and one drying and three coating and one drying is adopted. It is applicable to the surface of aluminum substrate such as building curtain wall, doors and windows, ceiling, roof and shop facade.
What is a plate heat exchanger? Plate heat exchanger is a new type of high efficiency heat exchanger composed of a series of corrugated metal sheets. Thin rectangular channels are formed between various plates through which heat is exchanged. Plate heat exchanger is an ideal equipment for liquid - liquid and liquid - steam heat exchange. Plate material: 304, 316,316L, titanium etc Thickness of plate:0.4mm-0.8mm Sealing ring material : nitrile rubber (NBR), EPDM, fluorine rubber. Overall heat transfer coefficient:3500-7500W/m�²�·K Advantages: 1.Heat transfer conditions:It is especially suitable for liquid-liquid heat exchange with large flow and small temperature difference. 2.Thorough cleaning:All can be disassembled for thorough cleaning. 3.Easy to change the heat exchange area or process combination: By increasing or reducing a few plates, the heat transfer area can be increased or reduced. By changing the plate arrangement or replacing several plates, the required flow combination can be achieved to adapt to the new heat transfer conditions. 4.Small in size :Compact and lightweight structure, small footprint, the floor space is one-third of the tube heat exchanger. 5.Light weight:The plate thickness of the plate heat exchanger is only 0.4~0.8mm, while the thickness of the heat exchange tube of the shell-and-tube heat exchanger is 2.0~2.5mm. The shell-and-tube shell is much heavier than the frame of the plate heat exchanger .The plate heat exchanger is generally only about 1/5 of the weight of the shell-and-tube type. 6.Low price: Using the same material, under the same heat exchange area, the price of the plate heat exchanger is about 40%-60% lower than that of the shell-and-tube type.� 7.High heat exchange efficiency :The heat transfer coefficient is 3-5 times higher than that of the tube heat exchanger 8.Low heat loss: The heat recovery rate can be as high as 90% or more. 9.The logarithmic mean temperature difference is large, and end temperature difference is small. Application 1.City heating 2.Inorganic chemical industry 3.Organic chemistry 4.Petroleum industry 5.Metallurgical industry 6.Food technology 7.Paper making process 8.Pharmaceutical industry � Shandong Qinglei Environmental Technology Co.,Ltd is an equipment manufacturer integrating design, production and assembly. Our products include heat exchangers, heat exchange units, pressure vessels, storage tanks, TCU temperature control systems, reactors, distillation towers, VOCS purification and recovery systems, vacuum frying machine. If you need any of them,please donot hesitate to let me know,I will reply you ASAP.
Calcium Stearoyl Lactylate(CSL) Characters: Ivory powder or flake-shaped solid. It can be dispersed well in hot water and soluble in ethanol and hot oils and fats with pleasant caramel-like odor. It is an anionic emulsifier with HLB value of 5.1. Applications: It can be used for multiple purposes such as emulsification, aging resistance, gluten fortifying and fresh-keeping in many kinds of food such as bread, steam bread, noodle, instant noodle and dumpling. It can also be used as an emulsifier in milk, non-dairy creamer, margarine, fresh cream, meat products, animal and vegetable oils, etc. (1) Increase the springiness, toughness and gas-holding capability of dough, increase volume of the bread and steam bread and improve the organization and structure. It can react with amylose to delay and prevent the food aging. It can make it easier to remove biscuits from moulds to produce smooth appearance, distinct layers and crisp feeling in mouth. (2) It can make hot and spicy food more pliable and softer and prolong the preservation time. (6) Enhance the quality of quick frozen food, improve their organization and structure, and prevent surface cracking and filling escaping. Usage: (1) It can be directly mixed well with flour for use.�?�¯ï¿½?�¿ï¿½?�½ (2) Put this product into warm water at about 60 with proportion of 1:6 to get paste shaped substance, ten add it into flour in proportion to obtain better effect. (3) When used in non-dairy creamer or this kind of substance, it should be heated well with emulsified substance to get homogeneous emulsion before further processing. Recommended Adding Amount: 0.2~0.5 %( Calculated by Flour, Refer to GB2760-2011) Technical Index Acid value (Calculated by KOH) / (mg/g)50- 86 Ester value(Calculated by KOH) / (mg/g)125- 164 Total lactic acid (W/%)32.0- 38.0 Calcium content (W/%)4.2- 5.2 Pb / mg/kg 2 Packaging Aluminized bag vacuum packing with nitrogen inside. Net weight:20KG/CTN(5KG *4) or packaged with moisture proof paper bag, 25kg/bag.. Storage & Transportation: Sealed and stored in the low temperature, dry, cool and well-ventilated place, in order to prevent from moisture and caking. Strictly forbid storing and trasporting with materials that is explorsive, combustible or deleterious. The shelf life is 12 months.
Disposable LDPE gloves, plastic gloves Material: Made by Low-density polyethylene (LDPE) or High-density polyethylene (HDPE) fabric. Size: S,M,L,XL Thickness:0.015-0.03mm. Color: white/blue Feature: Light, breathable dustproof and waterproof. Function: Suited to food processing, restaurant and hygienic applications & daily use. Sanitation and quality in accordance with the CE & ISO 13485 standards Packing:100pcs/bag,10000pcs/carton Different weight and thickness are available! Features: 1. The plastic gloves are the most economical of the disposable gloves. 2. They are a 0.015mm power free glove used primarily for light situations. 3. They protect hands from skin-irritating tasks, and keep foods away from germs, perspiration, and skin oils. 4. They are thin for extra sensitivity and economy. 5. Application: Excellent for food, vegetable picking, or surgical to avoid touching something directly making all is clean and healthy. Other Products MEDDOCARE Sell: 1. Cap: 1.1. Bouffant cap 1.2. Doctor cap:(surgical cap with tie/surgical cap with elastic) 1.3. Strip cap 1.4. Space cap 1.5. Peak cap 1.6. Round cap with fringe 1.7. Shower cap(PE) 2. Body wear: 2.1. PP/CPE Isolation gown :(With Knitted cuff/Elastic cuff) 2.2. Surgical gown:(Sterile/Non-sterile) 2.3. Lab coat:(PP/SMS) 2.4. Coverall: (PP/SMS/PP+PE) 2.5. Scrub suit:(PP/SMS) 2.6. Sauna suit:(PP/SMS) 2.7. Patient gown 2.8. Pants:(Man/Woman) 2.9. Brief:(Man/Woman) 3. Shoe cover/Boot Cover: 3.1. Non-woven shoe cover/boot cover 3.2. Non-shid shoe cover/boot cover 3.3. PE shoe cover/boot cover 3.4. CPE shoe cover/boot cover 4. Face mask: 4.1. Face mask with ear loops:(1ply/2ply/3ply/4ply) 4.2. Face mask with ties:(1ply/2ply/3ply/4ply) 4.3. Active carbon face mask:(3ply/4ply) 4.4. Face mask with eye shield:(3ply/4ply) 4.5. Dust mask:(120g/140g/160g/180g) 4.6. Paper mask:(1ply/2ply) 5. Other Main Products: 5.1. Gloves( HDPE/LDPE/CPE/TPE) 5.2. Apron:(Non-woven apron/PE apron) 5.3. Sleeve cover:(Non-woven sleeve cover/PE sleeve cover) 5.4. Bed cover/Bed Sheet 5.5. PE hair-cut cape 5.6. PE ear cover 5.7. PE raincoat/poncho 5.8. Wipe cloth/surgical dressing 5.9. Pillow case 5.10 Clear face mask
SMS Scrub Suit, Disposable Scrub Suit Specification: Regular Color:blue,white,green Material: SBPP,SMS,spunlace Weight:30-50gsm Size:S.M.L.XL.XXL Customer logo can be printed Certificate:CE,ISO,FDA SIZE(CM) SHIRT PANTS M 75X56CM 107X56CM L 77X59CM 108X58CM XL 79X63CM 110X61CM XXL 79X71CM 114X67CM Style/Pattern: two-piece set including Shirt and pants. Shirt: Collar : Around collar or V-collar Sleeves: without or short sleeves Pocket: available Pants: with tie on the waist, pockets are available. Packing:1set/pp bag,50bags/ctn Application: hospital, laboratory, etc. Feature: Bacterial released from thehuman body during the surery can pass through the commonly worn cotton scrub suits. Less risk of post-operative infections Less suffering for the patient A final cost reduction The OTM scrub suits is designed to fit comfortably under the surgical gown Other Products MEDDOCARE Sell: 1. Caps: Bouffant cap Doctor cap:(surgical cap with tie/surgical cap with elastic) Strip cap Space cap Peak cap Round cap with fringe PE shoe cover 2. Gowns: PP/CPE Isolation gown :(With Knitted cuff/Elastic cuff) Surgical gown:(Sterile/Non-sterile) Lab coat:(PP/SMS) Coverall: (PP/SMS/PP+PE) Scrub suit:(PP/SMS) Sauna suit:(PP/SMS) Patient gown Pants:(Man/Woman) Brief:(Man/Woman) 3. Shoe cover/Boot Cover: Non-woven shoe cover/boot cover Non-skid shoe cover/boot cover PE shoe cover/boot cover CPE shoe cover/boot cover 4. Face mask: Face mask with ear loops:(1ply/2ply/3ply/4ply) Face mask with ties:(1ply/2ply/3ply/4ply) Active carbon face mask:(3ply/4ply) Face mask with eye shield:(3ply/4ply) Dust mask:(120g/140g/160g/180g) Paper mask:(1ply/2ply) 5. Other Main Products: Gloves( HDPE/LDPE/CPE/TPE) Apron:(Non-woven apron/PE apron) Sleeve cover:(Non-woven sleeve cover/PE sleeve cover) Bed cover/Bed Sheet PE hair-cut cape PE ear cover PE raincoat/poncho Wipe cloth/surgical dressing Pillow case, pillow cover Clear face mask
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the worldâ??s best reserves in India. Talc is the worldâ??s softest and most hydrophobic mineral â?? insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications .under brand name â??NANOTALâ?? having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. NANOTAL also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. Itâ??s us use in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL 3000 is a high purity TALC POWDER [Having Average Particle Size D-50 : 1.00 microns and Top Cut D-97 : 5.00 microns ]. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, and scrub property, gloss, non-yellowing property, corrosion and coverage. It provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. It also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. NANOTAL Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL 530 is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL 1000 is a high purity TALC POWDER [Having Average Particle Size D-50 : 2.50 microns and Top Cut D-97 : 9.50 microns ]. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, and scrub property, gloss, non-yellowing property, corrosion and coverage. It provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. It also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. NANOTAL Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL 2000 is a high purity TALC POWDER [Having Average Particle Size D-50 : 1.80 microns and Top Cut D-97 : 7.00 microns ]. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, and scrub property, gloss, non-yellowing property, corrosion and coverage. It provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. It also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. NANOTAL Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
