Zero Thermal Expansion Silica Brick Suppliers and Manufacturers

SiO2: 95% for coke oven, blast furnace, glass furnace.

Silica bricks are the main species of silica-based refractories, where the mass fraction of sio2 is not less than 93%. Silica brick is a typical acid refractory bricks, the acid slag has a good resistance to al2o3, feo, fe2o3 and other oxides also has good resistance, but the resistance to alkaline slag is poor, easy to cao, k2o, na2o and other oxides and damage. Silicone brick softening temperature as high as l640-1680 â??, long-term use at high temperatures more stable. But the thermal resistance of silicon brick is poor, refractoriness is not high enough.

Fused silica brick has better thermal shock resistance, much lower thermal expansion, and can be used to do hot repair. Fused Silica Brick for Hot Repair of Coke Oven is similar to general silica brick, but it has better thermal shock resistance. The property of fused silica brick is similar to general silica brick, but it has better thermal shock resistance, much lower thermal expansion and it can stand suddenly change of temperature. It also can be heated in very short time after buildup and do not need to calculate thermal expansion. So we can directly use its cold size for masonry. Put on wooden pallets, tightened with iron stripes, covered with plastic bag, warped with film, shipped in pallet by container. Do corner protection and other measures to avoid products from breaking. And these packages should be under ISPM standard.

A brief introduction of silica brick Silica brick is a kind of acid refractory mainly made from tridymite, cristobalite and a small amount of residual quartz as well as glass phase. The raw material is natural silica sand whose SiO2 content should be more than 96%. The higher SiO2 content in silica sand, the higher temperature silica bricks resist. Silica bricks are used in the roof and superstructure of glass melting tanks as well as for hot repairs. Our silica brick advantages --Adopts high quality silica and advanced technology, our silica bricks enjoy the advantages of high purity, long service life, good thermal conductivity, high refractoriness under load, and good creep resistance. --In addition, it has accurate size tolerance, pure color and luster appearance. --Because of the good thermal shock resistance of silica brick, it is mainly used in the continuous operating furnace. --Supporting the use of other high quality refractories, our silica brick can extent the service life of float glass furnace to 8 years and double the service life of bottle glass furnace. Applications The silica brick can be widely used in coke oven, hot blast furnace, glass furnace and carbon furnace. In glass industry, it is mainly employed to build the doghouse crown, suspended wall of channel, top crown and inlet sealing. In detail, silica bricks plays the following role in different fields: --being the partition walls in coke oven carbonization and burning chamber; --metallurgy industry: used as refractories for steel making open hearth regenerator, slag pocket, soaking pit; --arch crown and other weight bearing areas in ceramic kilns, hot blast furnace and acid open hearth; --worked as building checker chamber, chute, combustion chamber, coking chamber and furnace arch in glass melting furnaces. Specifications 1.Higher SiO2 content of more than 96%, with true density of 2.34g/cm3, thus it has good performance in corrosion of acid slag. 2.Excellent resistance in high temperature. The melting temperature under load is 1620-1670â??. Durable, with no deformation under high temperature. 3.Good thermal shock resistance, High heat conductivity. 4.At 1450, there is 1.5-2.2% overall expansion which makes the joint-cutting dovetailed, thus silica bricks have good air tightness and strong structure.

Description Adopts high quality silica and advanced technology, our silica bricks enjoy the advantages of high purity, long service life, good thermal conductivity, high refractoriness under load, and good creep resistance. In addition, it has accurate size tolerance, pure color and luster appearance. Because of the bad thermal shock resistance of silica brick, it is mainly used in the continuous operating furnace. Supporting the use of other high quality refractories, our silica brick can extent the service life of float glass furnace to 8 years and double the service life of bottle glass furnace. It is widely used in coke oven, hot blast furnace, glass furnace and carbon furnace. Applications The silica brick can be widely used in coke oven, hot blast furnace, glass furnce and carbon furnace. In glass industry, it is mainly employed to build the doghouse crown, suspended wall of channel, top crown and inlet sealing. In metallurgy industry, it is adopted as the nozzle brick. The main applications Doghouse crown, suspended wall of channel, top crown and inlet sealing of glass furnace High temperature part of coke oven. Specifications High purity Long service life Accurate size tolerance Pure color Luster appearance Advantages Good thermal conductivity High refractoriness under load Good creep resistance High refractoriness

Features: 1. Good acid and slag resistance. 2. Good thermal conductivity. 3. High tridymite content. 4. Accurate dimension and good appearance. Application: Mainly used for coke oven of coking chamber and combustion chamber partition, steel open hearth of regenerative chamber and sediment chamber, soaking furnace, glass melting furnace, refractory silica brick materials and ceramic firing kiln and kiln of the vault and other supporting parts. Used in the construction of regenerative chamber, chute, combustion chamber, coking chamber, furnace roof etc. parts of the coke ovens. Also used in hot blast stove of high temperature bearing parts and the roof of acid open hearth furnace. Technical Index: Item Silica Brick for Coke Oven Sole, Walls Other Positions SiO2 % 94.5 94.5 A12O3 % 1.0 1.0 Fe2O3 % 1.0 1.0 CaO % 2.5 2.5 Apparent Porosity % 22 24 True Density g/cm3 2.32-2.33 2.32-2.34 Cold Crushing Strength MPa 40 35 Refractoriness Under Load (0.2MPa) 1650-1660 Residual Quartz % 0-1 Permanent Linear Change (1450 *2h) % 0-0.2 0-0.2 Thermal Expansion Rate 1000 % 1.28 1.30 Refractoriness 1710

Feature It is mainly made of top class silica, via shaping and burning under the high temperature, possesses high temperature resistant, high strength and low impurities, etc. â?º Advantage: 1) Good thermal insulaton effects 2) Good acid erosion resistance. 3) High softening point with temperature. 4) No shrink in burn repeatedly. Stable Capability, High Quality, Excellent Service, Competitive price is the most important advantage of our products. Application: The main applications are the low temperature parts such as blast furnaces and hot blast furnaces, waste incinerators and glass melting furnaces.

Advantages: 1.High purity. 2.Good thermal conductivity. 3.High refractoriness under load and high tridymite content. 4.Low true densit Application: 1.Widely used in hot blast stoves. 2.Used in high temperature sections of the checker chamber in hot blast stoves. 3.Used as low-cost alternative to andalusite and mullite checker bricks in hot blast stoves. 4.High refractoriness, average thermal shock resistance makes it suitable in consistent temperature environment. Technical Index: Item Silica Brick for Hot Blast Stove Wall bricks ,Dome Bricks Checker Brick SiO2 % Y95 Y95 A12O3 % ¨¹1.0 ¨¹1.0 Fe2O3 % ¨¹1.0 ¨¹1.0 Apparent Porosity % ¨¹22 ¨¹24 True Density g/cm3 ¨¹2.33 ¨¹2.33 Cold Crushing Strength MPa Y40 Y35 Refractoriness Under Load (0.2MPa) æ Y1650 Y1650 Residual Quartz % 1.0 1.0 Creep Rate 0.2MPa (155050h) % 0.6 ¨¹0.6 Permanent Linear Change ( 1450*2h) % ¨¹0.2 ¨¹0.2 Thermal Expansion Coefficient(1000æ) % ¨¹1.26 ¨¹1.26 Fumigated wooden pallet, using paper or non-woven fabrics between layers separated,plastic shrink film protected outside,finaly using straps. The size of wooden pallet is 95x95cm,95x100cm or as your requirements.

Silica brick is a kind of acid refractory mainly made from tridymite, cristobalite and a small amount of residual quartz as well as glass phase. The raw refractory material is natural silica sand whose SiO2 content should be more than 96%. The higher SiO2 content in silica sand, the higher temperature silica bricks resist, its refractoriness under load is as high as 1640 ~ 1670. Glass kiln silica brick has high temperature and volume stability, no pollution to glass liquid, chemical corrosion resistance, small bulk density, and can reduce the weight of furnace body. It also has the ability of resistance to acidic and alkalic steam attack with high performance of flushing resistance. It is mainly used to build the doghouse crown, suspended wall of channel, top crown and inlet sealing, and also to be used to build the checker chamber, chute, combustion chamber, coking chamber and furnace arch in glass melting furnaces. Silica brick has good corrosion resistance to glass liquid. It is the preferred refractory for crown construction of glass melting furnaces, in terms of cost, strength and of defect potential.

Silica mullite brick is a special high-alumina bauxite and silicon carbide as raw materials, made by a special sintering process, with a strong high wear resistance, thermal shock stability characteristics, in the course of the formation of protective layer, and other characteristics. Mainly used for cement rotary kiln transition zone, decomposition zone. Feature: High refractoriness under load Highâ temperature resistance Lowâ thermal conductivity Good insulatingâ property High flexibility Proper bulk density -

With the breakthrough of the suspension preheating and pre-decomposition technology in the cement industry and the increasing size of the equipment, the heat load of the kiln is significantly increased, the rotation speed is accelerated, the alkali corrosion is severe, and the lining life and equipment operation cycle are shortened, thus the requirements for refractory materials. More demanding. Its performance advantages are mainly manifested in: 1. High refractoriness under load and excellent high temperature resistance; 2. High strength, abrasion resistance, and easy to peel off and erosion; 3. Low thermal conductivity and good heat insulation effect; 4. Strong flexibility and heat resistance Excellent seismic performance; 5, moderate density, reduce the cylinder load.

Offered Yellow Corn Meal is known for its nutrientenriched content This feed preservative has been produced from natural extracts Its moisture content is 12 This feed contains a maximum 819 starch and up to 09 sand silica It offers 225 crude fiber and 4 crude fat Its crude protein based content is maximum 9 Besides these the feed also contains maximum 036 natural phosphorous and up to 008 natural calcium Free from foreign matters this Yellow Corn Meal is accessible in coarse mash form Its content is 100 vegetarian Key Advantages Uniform Quality Maintenance Zero Atmospheric Packing so longer shelf life Zero Production and Processing Expense for Buyer Safe Trade without any quality based apprehensions at mutual trade Round the Year Availability Best alternative of Yellow Corn Seed Mammoth Supply Ability Proximity to well equipped ports between 350 to 375 Kms Technical Specification Yellow Corn Meal YCM010309 Suitable as Animal Feed Yellow Corn or Poultry Feed Maize Crude Protein Between 75 9 Crude Fat Between 25 4 Crude Fiber Between 1 225 Moisture Maximum 12 Starch Content Between 75 819 Crude Ash Between 05 18 Sand Silica Between 02 09 Natural Phosphorus Content Between 025 036 Natural Calcium Content Between 001 008 Germination Index of the Seed Between 90 94 Foreign Matter Nil Crop Latest Cultivation Coarse Mash Size Mash Between 1418 GENERAL DETAILS Ingredients  Indian Yellow Corn Grade1 Ingredient Profile  100 Vegetarian Product Form  Coarse Mash Form Moisture Maximum 12 Product Branding HAF Net Weight  39 Kgs When Packed Product Pricing  On Unit Basis for each 39 Kgs Packing Production Capacity per Day  450 MTDay Factory Visit  Not Permissible Fumigation  Aluminum Phosphide or Methyl Bromide or any as per buyer specification Clinical Test Methodology  As per IS2052 Proximate Analysis on Dry Matter Basis  

Silica Brick for Coke Oven KNKSKS JG-94 Physical and chemical properties, dimension and appearance, strictly conform to DIN norm Application Construction of Coke Battery Coke Plant, Newly Built or Hot Repair

Silica bricks are the main species of silica-based refractories, where the mass fraction of SiO2 is not less than 93%. Silica brick is a typical acid refractory bricks, the acid slag has a good resistance to Al2O3, FeO, Fe2O3 and other oxides also has good resistance, but the resistance to alkaline slag is poor, easy to CaO, K2O, Na2O and other oxides and damage. Features: 1.Good acid and erosion resistance, powerful anti high-temperature strength. 2.Soften melting temperature is 1620~1670 °C. 3.Low thermal shock resistance. 4.Natural silica as raw material, plus regular mineralizer. 5.Ensure good bonding and structural strength of furnace. 6.Good heat resistance and long service life. Application: 1.Glass melting furnace, ceramic frit kiln, sodium silicate furnace, soaking furnace, ceramic kiln, etc 2.Coke oven's coking chamber, combustion chamber walls, steel open-hearth's regenerator and sediment chamber, etc. 3.Load-bearing parts of high temperature hot air furnace and acid open-hearth furnace roof, etc. Items Fire Proof Thermal Insulating SiC+SiO2,% 30 - Al2O3,% 65 50 Bulk Density,g/cm3 2.65 - Apparent Porosity,% 19 25 Cold Compressive Strength,Mpa 90 40 Refractoriness UnderLoad, ºC 1650 1680 ThermalShock Resistance,cycles(1100 ºC,water cooling) 20 20 Thermal Conductivity,w/m.k(350 ºC) 2.5 1.4

Silica brick is a kind of acid refractory mainly made from tridymite, cristobalite and a small amount of residual quartz as well as glass phase. The raw material is natural silica sand whose SiO2 content should be more than 96%. The higher SiO2 content in silica sand, the higher temperature silica bricks resist. Silica bricks are used in the roof and superstructure of glass melting tanks as well as for hot repairs.