Find Verified Hydraulic Counterbalance Valves Benchmark Sun Suppliers, Manufacturers and Wholesalers

Last October, Henry had planned to go to Hawaii with his family for a vacation. The day before he left, he was informed that a customer complained about the vibration problem of his company's hydraulic power unit during low-speed operation. The boss asked Henry to solve the problem immediately. As the purchasing manager of the company, he had to cancel the annual leave. The engineer tested the hydraulic system on site and preliminarily judged that the hydraulic counterbalance valve was abnormal. The engineer disassembled the hydraulic counterbalance valve and failed to find out the reason. The hydraulic counterbalance valve was tested separately, and each parameter was up to standard. Henry began to contact the local hydraulic counterbalance valve supplier and wanted to solve it as soon as possible, but there was no reply. Henry found the original hydraulic counterbalance valve manufacturer. The factory said that he OEM the hydraulic counterbalance valve completely according to their hydraulic counterbalance valve drawings. He also specially retested the hydraulic counterbalance valve in stock, and its parameter basis was qualified. Henry was embarrassed to face such a situation. Henry thought of AAK because we helped him solve the difficult problems of hydraulic counterbalance valves several times before. We received Henry's email and understood that neither the original manufacturer nor the local manufacturer provided solutions. According to the working video of the pressure unit provided by Henry, our engineers recognized their preliminary judgment that the hydraulic counterbalance valve was abnormal. The function of the hydraulic counterbalance valve is to balance the "negative load force" opposite to the required movement direction, which makes the hydraulic motor easier to control. The vibration problem in the complaint is that the hydraulic counterbalance valve affects the control ability of the balance circuit to the load. This is just our first guess about the fault. The specific situation needs to be determined in combination with the actual hydraulic counterbalance valve samples. Henry sent us the hydraulic counterbalance valve samples the next day. After our engineers disassembled it, we are 90% confident that our judgment is correct. The check valve throttling groove of their hydraulic counterbalance valve is a traditional design. According to the working condition of their pressure unit, the design of double triangular throttling groove of hydraulic counterbalance valve has a little influence on the stability of valve spool. The hydraulic counterbalance valves we shipped to a Russian customer 2 years ago also encountered similar problems. I suggest Henry redesign the structure of the hydraulic counterbalance valve. A month later, AAK sent out 10 samples of hydraulic counterbalance valves, Henry installed the equipment for commissioning, and there was no vibration problem.

hydraulic relief valves . purchased a batch of hydraulic relief valves for crane system in because the original supplier was not able to meet the delivery. He sent an email last week saying with hydraulic relief valves, the stability is 8% higher than that of the original supplier, and there is almost no external leakage. This surprised him. The use experience of hydraulic relief valves has benchmarked with their previous local hydraulic relief valve manufacturers The vast majority of hydraulic valve bodies are made of nodular iron, vermicular iron and gray iron and cast with resin sand as the molding medium. Therefore, there is sticky sand in the casting, which is easy to pollute the oil system and block the valve and filter, which is the key factor affecting the stability of hydraulic relief valves. Most of the common sand cleaning methods of hydraulic relief valves used in the industry are shot blasting and electrochemical sand cleaning, all of which have limitations. 1. Shot blasting can not completely remove the sticking sand from the valve hole with complex structure and small oil passage, which is easy to affect the tightness and product accuracy, and is not conducive to the stability of the hydraulic relief valves. 2. Electrochemical sand cleaning can relatively remove the sticky sand in the narrow oil passage, but it has high energy consumption, high operation intensity of workers, easy to have human errors, can not completely remove the sticky sand, and is not conducive to the stability of the hydraulic relief valves. Improving the quality of hydraulic parts processing process, improving the cleanliness level and ensuring the stability of hydraulic relief valves has always been the hard index of hydraulic relief valves. Auxiliary processing of hydraulic parts mainly includes: sand cleaning of valve body, deburring or residue treatment of parts and cleaning of hydraulic parts. How does do the sand cleaning of hydraulic relief valves technical team has continuously improved the sand cleaning process of hydraulic relief valves after years of technical improvement. For the sand cleaning of small complex castings, has its own unique sand cleaning 5 methods, namely: artificial aging - Pickling - rinsing - rust prevention - ultrasonic cleaning. Artificial aging is used to reduce the binding force between the casting and sand, acid pickling is used to remove the oxide skin at the joint between the sand and the casting to peel the sand from the casting, and then the explosion of compressed air during ultrasonic cleaning is used to peel off the sand, so as to achieve the purpose of sand cleaning. has its own unique advantages of sand cleaning 5 methods: (1) it is less affected by the casting structure; (2) it is

new hydraulic relief valve. The drawings of the hydraulic relief valve were sent 1 month after the confidentiality agreement was signed. The customer requested that if we were not able to develop it, they would witness us destroy the drawings and documents of the hydraulic relief valve by video. It's the first time for this customer to be so formal After receiving the drawings of hydraulic relief valve, we knew that it was to match with a set of aerospace equipment developed by a world top 500 enterprise in the engineers reviewed the drawings for 3 days and still didn't write the sample program. This hydraulic relief valve is not only small in size, but also has material requirements, machining accuracy requirements and use frequency requirements that exceed the parameter requirements of the hydraulic relief valves we have seen. We estimated that the overall development When we mentioned and give you 1 year of time. If the development is successful, you can wait for the order of hydraulic relief valve. If the development fails, this will be deducted from the payment for in the future. to say that the customer will prepay for the development cost of the hydraulic relief valve, but if it fails, we will need to refund it by deducting from the future payment gradually. I did not hesitate to reply to the email and was willing to try to develop this hydraulic relief valve. hydraulic relief valve development would be counted as the contribution of the technical team, and the failure would be counted as mine, because I can't fail to live up to the customer's support for our development. Some people in can not understand how this could be a kind of support. Maybe he didn't think about a question, that is, what would the mentality of the technical team be without customer support Behind these are two completely different ways of thinking. One is that if you haven't done it yet, think about failure first, think about whether there is a bottom plan first, and if not, don't do it. There is also a way of thinking, which is to think about how to start first. If conditions permit, start working first. The difference between these two ways of thinking is not just the difference between conservative and radical, but whether people are the key factor to create value. With the starting money, the hard work of the technical team and the best logistics

When I opened the mailbox this morning, I saw an from , which should be a re-order for the hydraulic relief valve, because he asked about the durability of hydraulic relief valve spool last week. Opening the , it is indeed the need for purchasing a large number of 420 hydraulic relief valves, and requiring 3 years of quality guarantee. is a purchaser of . 3 years ago, a customer of his company complained that the crane was easy to depressurize during work, resulting in the inability of the crane to bear the force. Especially after the working temperature reaches 55 C, the pressure cannot go up. Field engineers believe that this is a problem of the hydraulic system, such as low pressure regulation of the hydraulic relief valve, wear of the hydraulic system, or oil pollution. No abnormality was found after inspection. Finally, it was determined that the fault occurred on the hydraulic relief valve. After disassembling the hydraulic relief valve, it was found that the cone valve spool was worn, affecting the sealing of the hydraulic system, so the oil pressure could not rise. The customer does not understand why the valve spool of this hydraulic relief valve is worn after less than 2 years of use. The customer requested to replace with a batch of hydraulic relief valves with durability of more than 3 years and use them on these 12 faulty cranes. At that time, contacted more than 10 hydraulic relief valve manufacturers and got reply that the warranty could not be achieved for 3 years. Some hydraulic valve manufacturers replied that they only have 50% confidence. This result embarrassed Bruce. The customer requirements for the hydraulic relief valve could not be implemented, how he should explain to the owner. I received message from on the of can really provide a 3-year warranty hydraulic relief valve I replied directly: just give it a try then you will know. I can't make money with the trial orders of several samples, and you can't lose money. Maybe was stimulated and sent us the test order the next day for 4 hydraulic relief valves. also frankly told that two other hydraulic valve manufacturers would also try the order at the same time. Their plan is that each factory will be tested for 4 samples, with a total of 12 hydraulic relief valves to meet the urgent needs of customer first. About 2 years after the samples were sent, we received from again for another trial order of 8 hydraulic relief valves. I felt strange and thought that they actually didn't have big quantity order for hydraulic valves. Until last week, from his email, we learnt that they had tested the hydraulic relief valves provided by for 3 years. Indeed, 3 years later, hydraulic relief valves still worked normally, and the hydraulic relief valves provided by the other two manufacturers had faults in less than 2 years.

He has done very well and occasionally inquires about the price with HYDRAULIC VALVE. For the hydraulic check valves purchased some time ago, the production director found that 20% of the hydraulic check valves have parameters that do not meet the standard, so they must get new qualified ones to the workshop within 20 days, otherwise the delivery of customer order would be delayed. Charles asked the original manufacturer of the hydraulic check valve to complete the replacement within 2 weeks. The manufacturer is willing to replenish, but the production can be started only after 15 days, that is to say, it will take 30 days to replenish. tried to find other suppliers of hydraulic check valves, and all replied that it could not be completed in such a short time. realized that something was going to happen and began to look for a new hydraulic valve manufacturer, contacting factories one by one. thought that had also participated in the quotation of this hydraulic check valve, and the samples provided also met the requirements, but it was not considered because the quotation of was slightly higher than that of other hydraulic valve manufacturers by 7%. sent us an e-mail to ask whether the quotation of hydraulic check valve offered 6 months ago can be maintained, and if we can finish an urgent order of 100 hydraulic check valves in 10-12 days. I felt that this should be an order for hydraulic check valve encountered with problem. told us the truth. About 20% of the hydraulic check valves produced by the original factory were unqualified and rejected by their production director. Now he must replenish them as soon as possible. General hydraulic valve manufacturers are unwilling to make such aftercare orders, but HYDRAULIC VALVE don't think so, because , as a production factory, has the same goal as the importer, that is to serve users well, so is more willing to help customers and solve complaints from users together. Fortunately, the corresponding materials are in stock. Combined with the 24-hour production line, our production director conservatively estimates that it can be completed in 12 days. asked us to start blanking now and the hydraulic check valve order will be issued tomorrow. After 10 days, 100 hydraulic check valves were successfully finished. was very happy and quickly air freighted these hydraulic check valves to the Thanks to the God, 100 hydraulic check valves finally arrived at their workshop in 20 days. informed us by email that their engineers installed, debugged and tested hydraulic check valves, which were all normal. The 7% higher price was also agreed by his owner. The owner was very amazed that can deliver so quickly and the quality was better than that of the original manufacturer.

At the beginning of this year, received an order from African customer for excavators with a delivery time of 2 months, which means that all accessories must be in place within 1 month, including 600 hydraulic cartridge valves. The production time for the factory is a little more than 2 weeks. The purchaser Peter sent the order information of the hydraulic cartridge valve to all the hydraulic valve manufacturers he contacted before at the first time. More than 20 hydraulic valve manufacturers said that they could not complete the order of the hydraulic cartridge valve in such a short time, and it would take at least 3 - 4 weeks. His supervisor was not satisfied with this delivery time and asked him to find a new hydraulic valve manufacturer. After the email was sent, there was basically no sound. Peter was very helpless and worried. Peter asked Mark for help. HYDRAULIC VALVE to ask if could produce 600 hydraulic cartridge valves in 2 weeks and CC Peter, and joking at the end of the email that if HYDRAULIC VALVE could not complete the hydraulic cartridge valve order, then there is no need to waste time on looking for a new hydraulic valve manufacturer. According to the drawings they sent, technical department found that this was very close to the hydraulic cartridge valve supplied to a Russian customer last year, so the time in the early stage of the production of the hydraulic cartridge valve was saved. After the price of the hydraulic cartridge valve was approved, the process data could be configured on the computer on the same day and the production could be carried out the next day. 2 weeks later, 600 hydraulic cartridge valves were delivered on time, which was the first of all the accessories purchased by Peter to arrive at the company's warehouse. Peter didn't expect that the hydraulic cartridge valve he was most worried about was the first to be completed. Peter appreciated the advice from Mark and was also surprised that could complete this in 2 weeks, while his previous hydraulic valve suppliers needed 3-4 weeks. Mark told : 1. is his most trusted hydraulic valve manufacturer. can surprise him every time when the hydraulic valve order is urgent. 2. has a large amount of data storage and clear classification. For hydraulic valves with relevant data, they can use the most advanced UG / SOLIDWORK software and finite element analysis method to configure process data in 2 hours, which is 3-6 times faster than that of other suppliers. 3. is equipped with advanced machine tools imported from Swiss, coupled with their own modified fixtures, the production speed is accelerated and man-made errors are avoided at the same time. After listening to the introduction realized that only a good hydraulic valve supplier can make his purchasing smooth. successfully completed this urgent order.

a purchaser of in He is responsible for the procurement of hydraulic components. He has done an excellent job some time ago and has been praised by his supervisor for many times. Before the shopping season, he wanted to relax and planned to go on vacation with his family next week. A phone call from the owner disrupted all his plans. A major dealer in asked for help for a excavator produced by their company within 1 week . His engineer came to the user for routine maintenance and found that there was oil leakage in the hydraulic system. After pressure test, it was found that there was oil leakage in the hydraulic check valve, and 12 excavators had such faults. this hydraulic check valve, and got the reply that it was too cold in at this time. For such high frequency operation, even if the hydraulic check valve was replaced, it was estimated that the hydraulic check valve would still leak oil 1 week later. Unless more low temperature resistant sealing rings are used, this will take time to test, but the finishing time is to be determined. was so helpless, he had to find a new hydraulic valve supplier. asked several local hydraulic valve manufacturers. They either didn't have time to produce or require over 50pcs MOQ. After knowing these situations, the supervisor asked Daniel to give the dealer a plan that can be implemented within 10 days. had to cancel the vacation. thought of HYDRUALIC VALVE who he had contacted for inquiry before. He emailed us to ask whether we can produce the hydraulic check valve for the excavator, which needs to be resistant to low temperature. According to the drawings and working conditions provided by him, we advised that it takes 20 days to customize. All our existing hydraulic check valves are not close to this size. reiterated the hydraulic check valve needs to be low temperature resistant, and frankly told us what they are currently experiencing. I answered directly that the core lies in the low temperature resistant sealing ring. Daniel felt that maybe could solve this problem. After 18 days, we sent a sample of hydraulic check valve. The test results proved feeling. The parameters passed the test and there was no oil leakage at low temperature. The order for 12 hydraulic check valves was also easily confirmed. hanging heart can finally be put down. asked why hydraulic valve manufacturer needs time to be determined to test, and we solved it in 18 days. Why hydraulic valve manufacturer is unwilling to do this small quantities, but it is OK for hydraulic valve. At the same time, the price of hydraulic valve is cheaper than that made in and that made in the .

The Hydraulic Cartridge Needle valve that HydraForce can't make, AAK has done it in 30 days Rogelio is from Spain and we met 1 year ago. He sent inquiries about hydraulic cartridge valves to AAK for several times. Some time ago, he came to me and asked for help to make a batch of hydraulic cartridge needle valves. The hydraulic cartridge needle valve used on the hydraulic cold drawing machine they sold to Vietnam has expired the warranty period and needs to be replaced. This hydraulic cartridge needle valve is purchased from HydraForce, and it is not a standard part. HydraForce said that this valve was produced 2 years ago, it is out of stock now and will take 3-4 months to produce it. But the customer was not satisfied with this time frame and complained to his boss. In order to catch time, Rogelio contacted more than 10 Chinese manufacturers of hydraulic cartridge needle valves. They either could not benchmark with HydraForce, or they could not meet the time, so Rogelio was anxious. Rogelio remembered that AAK had supplied HydraForce for 9 consecutive years. He believed that I can help him. According to the hydraulic cartridge needle valve drawings provided by Rogelio, the production time is only 30 days. I told him that the lead time was only 30 days, and the manufacturing quality of hydraulic cartridge needle valve was up to the standard of HydraForce, few Chinese hydraulic valve manufacturers could meet these requirements. Rogelio thought that I was ready to give up, he was willing to give AAK 40 days and paid for 100 hydraulic cartridge needle valves the next day. 30 days later, AAK sent 100 hydraulic cartridge needle valves to their Vietnam factory. Rogelio informed by email last week that it was out of his expectation that AAK still completed the production in 30 days. Their customer was very satisfied with their replacement of the hydraulic cartridge needle valves. Rogelio also specifically mentioned that he had asked more than 10 hydraulic cartridge needle valve manufacturers, their lead time was at least 50 days and can not 100% guarantee to benchmark the manufacturing quality of HydraForce. AAK was the only one that could catch up with the delivery date and also benchmarked the manufacturing quality of HydraForce. For this non-standard hydraulic cartridge needle valve, AAK has 3 advantages, which are beyond the reach of most hydraulic cartridge valve manufacturers: 1.AAK adopts Japanese OKK ultra precision machine tool, and the machining accuracy of components can reach 0.01~0.3�¼m. The precision of shape and contour is 0.003 - 0.1�¼m. Its production efficiency is 30% higher, which is the cornerstone of AAK's ability to catch up the delivery. 2. AAK has been hydraulic cartridge valve ODM manufacturer of 3 world top 500 companies for 10 years. Its quality control process is more strict than the ISO certification system. We have been focusing on details and constantly optimizing technology.

The hydraulic valve blocks designed and produced by not only has high reliability and small pressure loss to ensure that there is no oil running between the channels, but also has compact structure, small occupied space, simple oil circuit and easy pipe layout, so as to ensure the high efficiency requirements of different actions of various actuator elements. The valve block can control the valve, which is easy to adjust and operate. hydraulic valve block was designed and proofed successfully at one time within 1 month, which impressed the engineers o The vast majority of hydraulic valve block manufacturers blindly proofed according to customer drawings, ignored working conditions, and did not understand the internal structure and working principle of hydraulic valve block. It is easy to cause hidden dangers in the hydraulic system, and the problem cannot be found. power insensitivity of the hydraulic system related to the hydraulic valve block We replied that this is difficult to judge because it is a system problem that needs to be checked one by one. the next day then we understood why he left such The power unit of a hydraulic system developed by his company needs a hydraulic valve block. Their engineers mentioned that the sensitivity of the power unit is the key and that all components need to cooperate closely. the hydraulic valve block manufacturer strictly controlled the accuracy according to the drawings, it could be easily done. After the hydraulic valve block is finished, it is installed to test the hydraulic power unit. After the oil pump is started, the instantaneous pressure supply at the oil outlet of the power unit does not come up, and it just supply normal pressure after a few minutes. After checking each component one by one, it is suspected that there are hidden dangers in the hydraulic valve block. After detecting the hydraulic valve block, there is no problem in the oil passage and channel of the hydraulic valve block the original hydraulic valve block manufacturer for analysis and solution. The manufacturer said that the hydraulic valve block was completely produced in accordance with the drawings and the accuracy was within the required range, and the reason for problem was unknown. hydraulic valve block , they all said that they could match the drawings, but not sure about the problems of the hydraulic valve blocks. hydraulic system and the picture of the oil circuit running direction of the hydraulic valve blocks of the original have ideas after 3 aspects of comparative analysis.

Today, wed like to introduce a hydraulic counterbalance valve, equivalent to Danfoss 1CE30. This model was developed for a customer in Brazil last July. Besides Brazil, till now, it has been shipped to Russia and India. Customers are very happy to have found a supplier with expected quality at a reasonable price. Here are the advantages of this counterbalance valve: * Economical and suitable for simple jacks. * Quick and easy field installation. * Can be used interchangeably with pilot one-way plugs of similar size. * The quality of this valve is benchmarking SUN, but price is much cheaper. * The service life is 2 times that of domestic hydraulic cartridge valve manufacturers in China Technical parameters of AAK E-1CE30 Counterbalance Valve: Rated Pressure: 350 bar (5000 psi) Rated Flow: 30 L/min (8 US gpm) Max total relief pressure: 350 bar (5000 psi) Max recommended load pressure at max setting: 270 bar (3900 psi) Pilot Ratio: 2.5:1; 5:1; 10:1 Leakage rate: 0.3 ml/min (5 drops/min) Temperature: - 30 ~ + 90 Fluids: Mineral-based or synthetics with lubricating properties at viscosities of 7.4 to 420 cSt (50 to 2000 sus) Cavity: A6610 AAK E-1CE30 counterbalance valve, equivalent to Danfoss 1CE30, has been exported to Russia, Brazil and India. You are welcome to try it out. AAK HYDRAULIC VALVES (836) 2025-02-17

With AAK variable pilot ratio hydraulic counterbalance valve, Milan's equipment energy consumption is reduced by 30% Milan from the Netherlands is an old customer of AAK. He purchased many non-standard customized hydraulic counterbalance valves from AAK. In March this year, Milan asked by email: can AAK design hydraulic counterbalance valves to reduce the energy consumption of equipment? It was learned that a hydraulic elevator developed by their company focused on the selling point of "low energy consumption and high efficiency", but after equipment commissioning, the energy consumption was not as good as expected and could not be promoted to the market. Their engineer knew that it was the problem of the hydraulic counterbalance valves, but there was no improvement after making efforts for several times. Milan contacted a number of hydraulic counterbalance valve manufacturers, but there was no gain. He was very anxious. According to Milan's hydraulic schematic diagram and the original design drawing of the hydraulic counterbalance valve, AAK engineers analyzed that the problem really lies in the control of the hydraulic counterbalance valves. AAK can redesign the hydraulic counterbalance valve with 90% confidence. Milan seems to have no better choice. He paid $2,000 development fee. After 50 days, AAK sent 20 samples of hydraulic counterbalance valves. Last week, Milan sent an order for 600 hydraulic counterbalance valves. At the same time, he informed that based on AAK newly designed variable pilot ratio hydraulic counterbalance valve, their engineer adjusted the working conditions of the equipment, improved the hydraulic principle, and saved more than 30% of the energy consumption of the hydraulic elevator. The promotion at the exhibition was also very smooth, the booking was hot, and their whole team was happy. But I'm a little unhappy. The price of Milan's regular order has dropped by 40% compared with the trial order. I told him that you can't let me "earn some money from selling cabbage with the heart of selling Heroin". Milan may also be amused, and directly revised it to the original price, only stressing the need to ship on time. How do AAK engineers design variable pilot ratio hydraulic counterbalance valves? In fact, it is simply based on Milan's energy consumption pain point, fight to the end. The variable pilot ratio hydraulic counterbalance valve is an innovation from the mechanical structure of the valve, which utilizes the characteristics of variable pilot ratio and pilot pressure. When stable, a low pilot ratio is used, and when unstable, a high pilot ratio is executed. Compared with the conventional standard hydraulic counterbalance valves, the pilot pressure required for full opening can be 30% lower under the same pressure and flow. At the same time, AAK's variable pilot ratio hydraulic counterbalance valve can keep the oil cylinder and motor moving more smoothly and quickly.

Yesterday, I received a repeat order for a hydraulic sequence valve from . The first order of this hydraulic sequence valve was placed 3 years ago. Before, I wondered why this hydraulic sequence valve had not been repurchased, thinking that it had been switched back to the United States for production. I really didn't expect to receive the repeat order after 3 years, and the quantity was more than 3 times that before. 3 years ago, company had a newly designed hydraulic pump to be produced in branch, and the pump needed hydraulic sequence valve. If purchasing the hydraulic sequence valve in the , it was expected to take 3 months or more. His owner wanted to try purchasing in , hoping to save half the time. According to the owner instructions, spent 3 days looking for hydraulic valve factories, selected 5 hydraulic valve manufacturers from more than 10 as their hydraulic sequence valve suppliers, and asked them to send reference samples of hydraulic sequence valves to Vietnam for testing. happily reported the purchasing status to his owner, who was satisfied. After received these hydraulic sequence valve samples, he arranged the technical department to match the working conditions for testing, but the results were poor. The matching clearance between the valve body and the valve spool of some hydraulic sequence valves was small. After an additional 20 pressurization, the valve hole was deformed and the valve spool would be stuck. All 5 hydraulic valve manufacturers said that after additional pressurization, they were not able to ensure the quality of hydraulic sequence valve. Time has been wasted for more than 2 weeks. At this time, if returning back to the United States to purchase hydraulic sequence valves, he would be scolded by his owner. to worry. When browsed , he felt that hydraulic valve was some different from the other hydraulic valve manufacturers. He emailed to inquire about the hydraulic sequence valve and frankly told us the problems he had encountered with Chinese hydraulic valve manufacturers. After several rounds of communication and technical team analysis of his drawings, we truthfully told him that existing hydraulic sequence valve samples could not meet his pressurization test. It takes 2 weeks to proofing according to the drawing. If the sample of the hydraulic sequence valve is approved and it takes 25 30 days to produce his order for the hydraulic sequence valve, calculates the time. If the sample of hydraulic sequence valve is successful, the time saving meets the requirements of the owner. If it is not successful, it will waste another 2 weeks. It seems that he has no choice. Somehow, feels that can give him hope and hopes that we can send samples as soon as possible.

For Pressure Reducing/Relieving Cartridge Valve equivalent to HydraForce PR10-36 that AAK developed last March, is approved by the Russian customer after 1 year of testing Last March, we developed and shipped a Hydraulic pressure reducing/ relieving valve equivalent to HydraForce PR10-36 for a Russian customer. Today, we are very happy to receive the feedback from the customer that the E-PR10-36 Pressure Reducing/Relieving Cartridge Valve developed by AAK is still running very smoothly after 1 year, the performance is very stable. They are preparing the PO and will place their regular order of 500 pcs with us next week. AAK hydraulic cartridge valve E-PR10-36 two advantages: 1. Pressure Rating 210 bar (3000 psi), benchmarking HydraForce 2. Its service life is 2 times that of its domestic peers Technical parameters of AAK E-PR10-36 pressure reducing/relieving cartridge valve: Working Pressure: 210 bar (3000 psi) Proof Pressure: 390 bar (5700 psi) Flow Rating: 56.8 lpm (15 gpm) Pilot orifice: 0.51 mm (0.020 in) Temperature Range: -40�°C ~ +120 �°C (with Buna N seals) Fluids: Mineral based or synthetic hydraulic fluid with lubricating properties Fluid viscosity range: 7.4 to 420 cSt (50 to 2000 ssu) Cavity: 10-3 AAK E-PR10-36 pressure reducing/relieving cartridge valve, benchmarking HydraForce PR10-36, has been approved by customer in Russia after 1 year of testing. You are welcome to give it a try. AAK HYDRAULIC VALVES (793) 2024-04-23

Hangzhou top hydraulic co., ltd is a oem professional manufactory of custom made made hydraulic power unit and hydraulic cylinder, also have hydraulic valves. We have yuken stand and rexroth stand oem factory solenoid valves. Pls send your request to tophydraulic at 163 doc com Carton box

1. Sales and supply new or used hydraulic power unit, hydraulic pump, hydraulic motor, hydraulic cylinder, hydraulic control, hydraulic valve, spare parts etc. 2. Installation of winche, haulers, cranes, steering system etc. 3. All kinds of hydraulics repair & modification works. Standard