Concrete Reinforcing Mesh Suppliers and Manufacturers

Welded Wire Reinforcement (WWR) provides the exact size of reinforcement where needed through variable bar size and spacing, thereby reducing steel waste. Plain Square Mesh sheets are a multi-purpose mesh and complies with AS/NZS 4671 : 2001 Steel reinforcing materials. Plain Square Mesh sheets are available in 6 x 2.4 m. SL72 6.75@200 6.75@200 41kg

Concrete reinforcement welded steel wire mesh.

Concrete slab mesh is reinforced welded wire mesh panels. This reinforced welded wire mesh panels are made of galvanized welded wire mesh for constructional uses. For example, block slab structure reinforcing, and hollowed slabs reinforcement, building wall reinforcement and support wall reinforcement. It has the continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry walls. Joint reinforcement has long proven to be necessary for superior performance of masonry wall construction. Variety: truss mesh reinforcement. Ladder mesh reinforcement. Available material: hot dipped galvanized, electro galvanized or stainless steel.

Concrete reinforcing mesh, trench rib mesh, welded wire mesh, galvanized wire, back wire, gabion box, temporary fence.

Product Name: Ribbed wire International standard: MS 144:2001 RM ribbed wire has a ribbed ontop of plain round wire, and it is come with either in coils form or cut to sizes length. This ribbed wire are widely used in the fabrication of reinforcing mesh. It enhances the performance of structural concrete slabs and increase the tensile strength. Sizes: 6.00mm 7.00mm 8.00mm Lengths: 4 meters 12 meters Tensile strength N/mm2: Min 500 - 1275 Packing: a) Cut to sizes length, either straight or folded per bundles b) Coil form in 500 1 ton per coil. Application: 1. manufacture of wire mesh fabric of reinfocement concrete 2. prestressing of concrete 3. reinforcement for concrete slabs 4. partition panels 5. building construction 6. ties and lifting 7. general engineering or construction purposes

Australian coal, australian diesel, brazilian sugar, construction steel, lng (liquified natural gas).

Construction reinforcement mesh was made by plain steel wire. It main used on building construction complied with standard AS NZS 4671-2001. The material is 250N, 500N, 500L, 300E, 500E, the mesh size is 150x150mm, wire diameter is 5.3mm and 4.0mm and the overhang length is in both sides. These specificate is very pouplar in New Zealand civil engineering field. More features of construction reinforcement mesh and ours as below: 1. high quality raw material 2. electric resistance welding machine made it which has firmly solder join, size precision,and appearance good-looking 3. Professional management team 4. Complete QC rules and regulations 5. A full of laboratory testing instruments Advantage of construction reinforcement mesh by AS-NZS 4671-2001 standard: 1. Save 30% of steel bar dosages 2. Reduce 50%-70% work time, improve construction progress and shorten construction period. 3. Cut down 5%-10% construction cost 4. Used widely,it has a good market development prospects. The specification of construction reinforcement mesh by AS-NZS 4671-2001 standard as below: concrete reinforcing mesh specification Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6x2.4m sheets Cross-sectional area/m width No. x dia., mm Pitch, @mm No. x dia., mm Pitch, @mm Unit area, kg/sqm Sheet, kg Long' l bars, sqmm/m Cross bars, sqmm/m structural SE92 13 X9.0 200 30 X9.0 200 5.0 75 318 318 SE82 13 X8.0 200 30 X8.0 200 3.9 59 251 251 SE72 13 X7.0 200 30 X7.0 200 3.0 45 192 192 SE62 13 X6.0 200 30 X6.0 200 2.2 33 141 141 Non-structural SL51.5 17 X5.3 150 40 X5.3 150 2.2 32 147 147 SL41.5 17 X4.0 150 40 X4.0 150 1.3 19 84 84

Reinforcing Trench Mesh made from CRB550(550MPa) ribbed wires. The reinforcing trench mesh products all come 6.0m longs, available in 3-Bar, 4-Bar, 5-Bar and 6-Bar, as well as 8, 11 and 12mm wires. Its long, narrow sheets of concrete reinforcing mesh, has the continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry walls. Joint reinforcement has long proven to be necessary for superior performance of masonry wall construction. Used specifically for residential footing trenches, paths or other narrow spaces. Length m Width m Longitudinal Wires mm Cross Wires mm Mass Kg 6.0 0.2 7.6 @ 100 4.77 @ 300 7 6.0 0.3 7.6 @ 100 4.77 @ 300 9 6.0 0.4 7.6 @ 100 4.77 @ 300 12 6.0 0.5 7.6 @ 100 4.77 @ 300 14 6.0 0.2 10.7 @ 100 4.77 @ 300 13 6.0 0.3 10.7 @ 100 4.77 @ 300 18 6.0 0.4 10.7 @ 100 4.77 @ 300 22 6.0 0.5 10.7 @ 100 4.77 @ 300 27 6.0 0.2 11.9 @ 100 4.77 @ 300 16 6.0 0.3 11.9 @ 100 4.77 @ 300 22 6.0 0.4 11.9 @ 100 4.77 @ 300 27 6.0 0.5 11.9 @ 100 4.77 @ 300 33

Trench Mesh All trench mesh sheets are supplied in 6m lengths at varying width increasing from 200mm in 100mm increments. Trench mesh is used for both footings 2 layers of trench mesh and slab edge thickening one layer trench mesh with sheet mesh over. You should normally allow 65mm minimum to the edges and bottom of the footings using plastic bar chairs or trench mesh supports to keep the mesh in place.  Trench mesh is designated as x-L8TM, x-L11TM or x-L12TM. The x is the number of main bars.

Steel Reinforcing Mesh Roll is used to provide tensile strength and crack control to structural concrete elements. Steel reinforcing mesh is the thin ribbed wire that can be make rolls presentation. Advantages to save more than 33% of steel, reducing costs 10% -30%; increase the speed of construction can shorten the duration of about 80%; to improve the quality of engineering structures, and concrete bonding anchoring reliable, smooth reinforcement bond strength equal to three times more, and the overall good, deviation is small, anti - cracking performance above 75%. Application Retaining and shear walls Beams and columns Concrete paving overlays Precast concrete elements Suspended floor slabs Swimming pool and gunite construction size(mm) 2.8-5.3 Reinforcement spacing(mm) Longitudinal wire 50-200mm Cross wire 30-1000mm Sheet size Length 2-50m Width 1-1.3m Mechanical and process property Meet GB/T1499.3-2002 standard;AS/NZS 4671; 2001,BS 4483:2005,A185-02

Reinforced Mesh Sheets Reinforcing mesh sheets, also known as reinforcing mesh or welded wire mesh, is a precast panel made of steel wires arranged in a grid pattern. It acts as an internal skeleton for concrete, designed to increase its strength and prevent cracking. Reinforcing mesh sheets help distribute stresses evenly throughout the concrete, reducing the risk of cracking, deformation and structural damage. It also helps to control shrinkage and cracking during the curing process, improving the overall quality and service life of the concrete structure. Reinforcing mesh sheets are mainly used in the construction industry to reinforce concrete structures and improve their durability, stability and load-bearing capacity. Reinforcing bars are embedded in concrete elements such as slabs, walls, columns and foundations to provide additional support and resistance to tensile forces such as bending, shear and temperature changes. Main features of steel wire mesh Strength Enhancement - The primary use of steel wire mesh is to reinforce concrete structures, increasing their tensile strength and preventing cracking and structural damage. By distributing the load more evenly throughout the concrete, steel mesh enhances the overall strength and durability of the structure. Versatile - can be used in construction, industrial, commercial and even residential applications. Crack Control: reinforcing mesh helps control concrete cracking by providing support and reinforcement in areas susceptible to pressure and tension. This helps maintain structural integrity over time and reduces the need for costly repairs. Structural Stability: By reinforcing concrete slabs, walls and foundations, wire mesh improves the structural stability of buildings and infrastructure. It helps prevent sagging, sinking and shifting, ensuring that structures remain stable and safe. Flexibility: Reinforcing wire mesh is available in a wide range of sizes, shapes and configurations to meet different construction requirements. Cost-effective: Although the initial cost of reinforcing mesh is high, long-term cost savings can be realized by reducing maintenance and repair needs.

Trench Rib Mesh All trench mesh sheets are supplied in 6m lengths at varying width increasing from 200mm in 100mm increments. Trench mesh is used for both footings 2 layers of trench mesh and slab edge thickening one layer trench mesh with sheet mesh over. You should normally allow 65mm minimum to the edges and bottom of the footings using plastic bar chairs or trench mesh supports to keep the mesh in place.  Trench mesh is designated as x-L8TM, x-L11TM or x-L12TM. The x is the number of main bars.  3-L8TM has three bars, which are 8 mm in diameter.  4-L11TM has four bars, which are 11 mm in diameter.

Trench Mesh is made specifically for use in residential footing trenches. Made from grade D500L ribbed reinforcing wire, Trench Mesh is made using a variety of longitudinal wires up to 12mm diameter. Cross wires are â?¯at 300mm centres. Sheets are made in 6m lengths, with widths varying from depending on the number of longitudinal wires. The longitudinal wires are at 100mm centres. The product code, for example L8TM3, refers to the ductility grade (L), diameter of main wires (8) and the number of main wires (3). Other sizes are available, contact us for more information.

we are able to offer a superior quality range of Reinforcement Mesh. All our products are available in various sizes, designs, and shapes at market leading prices to meet the demands of customers.