Double Part Thimble Eye Double Part Basket Grommet Round Application for Grommat Grommat slings can be fabricated in very short circumstances. The reason is this: Grommat slings are made from one continuous length of strand or wire rope. This requires only one tuck-in point as compared with six tuck-in points needed manufacturer an endless sling. A Grommat consists of an endless rope having construction 6/1 construction & is used where high ultimate breaking strength of the rope is required beyond the limits of a single part rope. A strand of sufficient length to complete the Grommat shall be obtained by either of the following methods: Method A: An order strand shall be unlaid from a specimen of 6/1 rope conforming to the requirement of the customer. Method B: Unlaying from a specimen of 6/4 rope having strands in all respects equipment to those obtained by method A above. Method C: Using a virgin strand either prefromed or post formed & in all other respects equivalent to those obtained by method A & B. During the course of construction of a Grommat the performed lay of the strand shall be maintained and shall not be interfered with except when laying in the core for which purpose length of strand left to form the core should be straightened . The length of the strand required to form a Grommat shall be equal to about 7.5 times the parameter of the Grommat in case of spliced Grommat. But in case of complete streamline splicing length shall be 4 times the effective length. Butt Splice The two ends of the rope should be joined together by two five –tuck splices. Number of Tucks The splices shall be tucked three times the full size of strand, a fourth time with the strand each reduced to half the original number and a fifth with the strands each further reduced to one third the original number. The heart strand is to be rowed in during tucking so that a double heart is produced for at least the length of the first three tucks in both directions. Method of Tucking The Tucks of the Splice shall be made over one strand and under one strand against the lay of the rope. The heart strand of the rope shall not be removed when the strands are opened out for tucking, but may be cut to a suitable length. Finishing The ends of the splice in way of the twisted off ends of wire that is between the end and the third tuck shall be tightly served with seizing wire, after parcelling with canvas, Hessian or wax paper.
Wire Rope Nets For Cargo Lifting Inner Dia Outer Dia Mesh 12mm 22mm 6" x 6" or 4" x 4" 16 mm 24 mm 6 " x 6 " or 4 " x 4" We recommend Steel wire rope Galvanised 6/19 const. FMC tensile strength 1960 N/mm2 RMO lay Typical Slinging Methods (Used singly and two single legs used together)
Two leg wire rope sling with main ring at top and hooks at the bottom. Three leg wire rope sling with main ring at top and thimble at the bottom. Four leg wire rope sling with main ring and intermediate ring at top with bow shackle at bottom. Four leg sling with main ring with thimble at top and plain loops at bottom. Braided / Plaited belt lifting slings - Available in standard lts. of 10m &10 in capacities ranging from 10 to 40 tons with steel core ropes.
Flattening Test - Ferrules shall be pressed, along the major axis until the inner, surfecestmeet. Multipurpose, Portable, Universal, Gearless, Hand, operated Pulling and Lifting machine, Supplied, complete with telescopic, operating handle and, standard Length of super flex steel fibre-mixed core, wire-rope fitted with Hook or Shackle at one end and, fused and tapered at the other end. After completion of the test, there shall, be no visible crack on the ferrule. Type, Normal Size, Length before Pressing Min., Length after pressing Min, Thickness Min T, Suitable for Normal Wire Rope Size, Lower Limit, Upper Limit, (1), (2), (3), (4), (5), (6), (7), Type A , 3, 11, 17, 1.61, 2.00, 3.15, 4.0, 10, 22, 1.7, 4.40, 4.75, 6, 10, 23, 2.1, 5.85, 6.30, 8, 27, 34, 3.0, 7.85, 8.40, 9, 30, 33, 3.50, 8.80, 9.45, 10, 32, 35, 3.75, 9.80, 10.50, 11, 36, 43, 5.25, 10.75, 11.55, Type B, 10, 45, 53, 4.2, 11.75, 12.65, 15, 46, 50, 3.8, 13.76, 15.75, 17, 50, 60, 5.2, 15.76, 17.85, 19, 56, 62, 5.00, 17.86, 19.99, 21, 62, 70, 6.20, 20.00, 21.99, 23, 78, 86, 7.55, 22.00, 23.89, 25, 83, 94, 8.00, 24.00, 25.99, 27, 92, 108, 8.85, 26.00, 27.99, 29, 98, 114, 9.85, 28.00, 29.00, 31, 101, 115, 10.00, 30.00, 31.99, 33, 105, 118, 11.07, 32.00, 33.99
Nominal size of rope A, C, D, F, G, K, R1, R (1), (2), (3), (4), (5), (6), (7), (8), (9), 08, 33, 11, 46, 9, 4, 3.5, 25, 12, 10, 44, 15, 56, 11, 6, 5.5, 32, 16, 12, 60, 20, 82, 13, 8, 7.5, 44, 22, 14, 60, 21, 82, 15, 8, 7.5, 44, 22, 16, 70, 23, 94, 17, 10, 29.5, 50, 25, 18, 80, 26, 104, 19, 12, 11.0, 56, 28, 20, 88, 28, 116, 21, 12, 11.0, 64, 32, 22, 100, 30, 125, 24, 14, 13.0, 72, 34, 24, 104, 33, 140, 26, 14, 13.0, 76, 38, 25, 114, 36, 150, 27, 16, 14.5, 82, 42, 29, 124, 39, 165, 31, 18, 16.5, 88, 44, 32, 140, 45, 190, 34, 20, 18.5, 100, 50, 35, 154, 50, 208, 38, 20, 18.5, 114, 56, 38, 169, 56, 234, 41, 22, 20.5, 125, 64, 41, 169, 56, 234, 44, 22, 20.5, 125, 64, 44, 190, 65, 260, 47, 25, 22.5, 140, 68, 48, 206, 67, 275, 51, 28, 25.5, 150, 75, 51, 229, 72, 300, 55, 32, 29.5, 165, 78, 54, 229, 76, 300, 58, 32, 29.5, 165, 78, 57, 243, 78, 330, 61, 34, 31.5, 115, 88, 64, 276, 88, 375, 69, 38, 35.5, 200, 100, All dimensions in millimetres., Note, For wire ropes of intermediate sizes, the next larger size of thimble shall be used., Dimension M is the standard pin hole and the largest pin-hole for each thimble. Should a, smaller pin-hole be required the diameter of this shall be stated in the enquiry and order.
Features Basket is cast steel. Wedge socket terminations have an efficiency rating of 80% based on the catalog strength of XXIP wire rope. Wedges are color coded for easy identification. Blue - largest wire line size for socket. Black - mid size wire line for socket. 7/16" on US4 9/16" on US5 Orange - smallest wire line size for socket. Cast into each wedge is the model number of the socket and the wire line size for which the wedge is to be used. Cast into each socket is the name "McKissick", "Crosby" or "CG", its model number and its wire line range. By simply changing out the wedge, each socket can be utilized for various wire line sizes (Ensure correct wedge is used for wire rope size). Load pin is forged and headed on one end. US-422 wedge sockets contain a hammer pad (lip) to assist in proper securement of termination. Crosby products meet or exceed all the requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B20.26. UWO-422 Wedges are to be used only with the US-422 Wedge Socket Assemblies.
Close Spelter Sockets All Dimensions in mm.
Rigging / Bottle Screws Refer IS : 6132 (Part II) 1972 for Dee Shackles Refer IS : 2315 - 1978 for Solid Thimbles Dimensions For Tubular Bodies And Screwed Eyes Nominal Size Dia of Rope mm H1 B C Dia D Dia E F Dia Min K Dia M Proof Load kn Safe Working Load kn Closed mm Open mm M12 8 330 525 230 27 10 4 20 12 177 10.0 5.0 M16 10 370 550 230 27 10 4 22 12 197 18.0 9.0 M20 12 400 570 230 34 10 4 25 16 211 28.0 14.0 M24 14 475 700 300 34 12 5 32 16 246 36.0 18.0 M27 16 550 825 360 43 12 5.5 35 20 290 44.0 22.0 M30 18 550 825 360 43 14 5.5 38 20 290 63.0 31.5 M33 20 600 875 380 48 14 6.5 44 25 325 75.0 37.5 M36 22 600 875 380 60 16 6.5 47 25 325 86.0 43.0 M39 25 660 960 400 60 16 6.5 50 25 350 100.0 50.0 M45 29 700 960 400 76 19 6.5 60 28 378 112.0 56.0 M52 32 750 1000 400 76 19 8 70 36 406 144.0 72.0 M56 35 775 1025 400 83 19 8 73 36 421 194.0 97.0 M60 38 800 1050 500 90 20 9.5 76 40 440 214.0 107.0 M64 41 1070 1450 580 95 20 13 91 47 580 286.0 143.0 M68 44 1120 1590 620 103 20 14 96 51 635 342.0 171.0 M75 48 1270 1700 660 111 20 14 103 57 690 400.0 200.0 M80 51 1360 1760 700 119 20 15 112 63 740 500.0 250.0 M90 54 1440 1860 740 127 20 16 122 69 790 624.0 312.0 Note : For intermediate sizes of wire ropes, the next larger size of bull dog grip shall be used.
SL- 450 Front and Side View Sealinkers Clamps Each clamps has a product Identification Code for Material traceability, the name Sealinkers or SL, and a size forged into it. Entire Clamps are galvanized / Powder Coated to resist corrosive and rusting action. Only Genuine SL Clamps have a Yellow colour for instant recognition. All Clamps have rolled threads and extra heavy nuts. Rope Size Dimensions (mm) Min No. of Clamps Amt. of Rope to Turn Back in (cm)P (in.) (mm) A B C D E F G H 3/8 9-10 11.2 38.1 19.1 25.4 23.1 19.2 41.4 49.3 2 16.5 1/2 13 12.7 47.8 25.4 30.2 28.7 22.4 48.5 58.0 3 29.2 5/8 16 14.2 60.5 31.8 33.3 34.0 23.9 52.5 63.5 3 30.5 5/4 18-20 15.8 70.0 36.6 38.1 35.8 26.9 57.0 72.0 4 46 7/8 22 19.1 79.5 41.2 44.5 40.4 31.8 62.0 80.5 4 48 1 24-26 19.1 89.0 46.0 47.8 45.2 31.8 67.0 88.0 5 66 1 1/8 28-30 19.1 98.5 51.0 51.0 48.5 31.8 71.5 91.0 6 86 1 1/4 32-34 22.4 108 45.0 58.5 55.5 36.6 79.5 105 7 112 1 3/8 36 22.4 118 58.5 60.5 58.5 36.6 79.5 106 7 112 1 1/2 38-40 22.4 125 60.5 65.5 62.0 36.6 86.5 113 8 137 1 3/4 44-46 28.7 146 70.0 77.5 74.5 46.0 97.0 134 8 155 2 48-52 31.8 164 76.0 86.0 83.5 51.0 113 149 8 180 Note Refer to table I in following these instructions. Turn back specified amount of rope from thimble or loop. Apply first clip one base width from dead end of rope. Apply U-Bolt over dead end of wire rope - live end rests in saddle (Never Saddle a dead horse!).Tighten nuts evenly, alternate from one nut to the other until reaching the recommended torque.
Manufactured in ISO 9001:2000 Certified Company Assured quality and Interchangeability of parts Truely Modular Construction Easily accessible separate brake, motor, drum, gear box & panel unit. Seamless Pipe Accurately Machined rope drum. Long Life. Unique and sturdy rope guide Arrangement Prevents rope slackening and easy change of rope. Precision Machine Cut case-Hardened Alloy steal gears. Noiseless Operation Long life Fail safe Disc Brake Trouble free operation and ease of adjustment Built in Control Panel with Std. Electricals Ready to use
Specification Method of use Rated volt(V) Input(w) Rated lifting weight(kg) Lifling speed (m/min) Lifting height (m) Quon/CTN (Pcs) Pocking dim-ension(cm) G,W,/N,W, (kg) HGS-B100-12 PA2OO Single-hook 220/230 450 100 10 12 2 46X36X16 24/22 Double-hook 200 5 6 HGS-B125-12 PA25O Single-hook 220/230 500 125 10 12 2 46X36X16 25/23 Double-hook 250 5 6 HGS-B150-12 PA3OO Single-hook 220/230 550 150 10 12 2 46X.36X16 26/24 Double-hook 300 5 6 HGS-8200-12PA4OO Single-hook 220/230 750 200 10 12 2 52X41X17 35/32 Double-hook 400 5 6 Single-hook 220/230 900 250 10 12 2 52X41X17 36/33 Double-hook 500 5 6 Single-hook 220/230 1050 300 10 12 2 52X41X17 37/34
DSQ Vertical Plate Lifting clamps are used for lifting and turning over plates from horizontal to vertical positions. DSQ Vertical Plate Lifting clamps are made with hardened steel jaws for firm grip and proper locking. DSQ Vertical Plate Lifting clamps in a small easy to handle tool, incorporated with a spring lock which facilitates attaching of the clamps to the plates. Model WILL Opening (mm) Weight (Kg) DSQ1 1 50 3.7 DSQ2 2 55 6.3 DSQ3 3 70 10.5 DSQ5 5 90 19.3 DSQ8 8 130 40 DSQ12 12 150 52 DSQ16 16 160 55 Warning Do not exceed Working Load Limits. Avoid Superficial Gripping. Do not exceed specified angle of Lift (Not more than 60). Check the cams periodically for excessive wear and tear and reject if found unsafe.
Model SL - PLC Model : SL - PLC CAPACITY Shackle Size Plate Size EACH PAIR 1.5 3 16 X 19 16 2.5 5 16 X 19 25 4 8 19 X 22 28 5 10 19 X 22 32 7.5 15 25 X 28 35 10 20 25 X 28 45
I - Beam Clamps (Model: SL - IBC) Capacity Flange Width 1 3" - 7" 2 3" - 7" 3 3" - 12" 5 4" - 13" 10 4" - 13" 15 5" - 16" 20 5" - 16" Spare Parts for IPTK Safety Lifting Clamps: Order No. 1. Body Complete 1041 2. Hoisting Eye Complete 1235 26. Hingeshaft Complete 0232 36. Screwed Spindle Complete 1362 Important Features Lower construction height due to integrated traverse. Reduced Stress on I - Beam flange due to specially designed clamp jaws. Adjustable for a wide range of I - Beam widths & Profiles (INP, IPE & IPB) Strong Industrial Design Clamp corresponds to standard specification for vertical load pick-up. Each quipment is serially numbered, tested by a competent authority 50% overload & is given Test Certificate. Optional feature special ofshore version model IPTKO (including 3.lB certificate)
Factor Of Safety 5:1 Tensile Strength: 1770/1960 N/mm2 Note The capacity indicated in the above table, for basket hitch and choker itch is for guidance only, vertical column is the actual load the slings can be tested and certified in other words safe working load is applicable for vertical lift only.
Thread Size D, S.W.L.@ 0 () Kg., A, mm, B, mm, E, mm, F, mm, G, mm, H, mm, J, mm, Coarse, Pitch, M8, 160, 6, 20, 20, 6.3, 20, 15, 1, 1.25, M10, 250, 7.7, 24, 24, 8, 25, 17, 1, 1.5, M12, 400, 9.4, 28, 28, 9.5, 30, 20, 1, 1.75, M16, 630, 13, 34, 34, 12.5, 36, 24, 1, 2.0, M20, 1000, 16.4, 40, 40, 16, 45, 27, 1, 2.5, M24, 1600, 19.6, 48, 48, 19, 53, 31, 2, 3.0, M30, 2500, 25, 56, 56, 24, 64, 39, 2, 3.5, M36, 4000, 30.3, 67, 67 x, 28, 75, 48, 3, 4.0, M42, 6300, 35.6, 80, 80, 34, 90, 56, 3, 4.5, M48, 8000, 41, 95, 95, 38, 100, 65, 3, 5.0, M56, 10000, 48.3, 112, 112, 45, 119, 73, 4, 5.5, M64, 16000, 55.7, 125, 125, 50, 135, 85, 4, 6.0, M72, 20000, 63.7, 140, 140, 58, 153, 95, 4, 6.0, M80, 25000, 71.7, 160, 160, 63, 165, 110, 4, 6.0, M90, 32000, 81.7, 180, 180, 71, 180, 125, 5, 6.0, M100, 40000, 91.7, 200, 200, 80, 195, 140, 5, 6.0
W.L. at 0o kg, Size Dia. A, Coarse Pitch, B, D, E, F, G, H, M, Approx, Wt. each kg., 85, 8, 1.25, 20, 6, 20, 8, 18, 12, 10, 0.06, 150, 10, 1.50, 25, 8, 25, 10, 22, 18, 12, 0.11, 220, 12, 1.75, 30, 10, 30, 12, 26, 22, 14, 0.18, 380, 16, 2.00, 35, 12, 35, 14, 30, 28, 16, 0.28, 570, 20, 2.50, 40, 14, 40, 16, 35, 30, 19, 0.44, 810, 22, 2.50, 45, 16, 45, 18, 40, 35, 21, 0.55, 1050, 24, 3.00, 50, 18, 50, 20, 45, 38, 24, 0.74, 1700, 30, 3.50, 65, 22, 60, 24, 55, 45, 28, 1.66, 2500, 36, 4.00, 75, 26, 70, 28, 65, 55, 32, 2.7, 3400, 42, 4.50, 85, 30, 80, 32, 75, 65, 38, 4.0, 5200, 48, 5.00, 100, 35, 90, 38, 85, 70, 46, 6.4, 6500, 56, 5.50, 110, 38, 100, 42, 95, 80, 50, 8.8, 8700, 64, -, 120, 42, 110, 48, 105, 90, 58, -, 13000, 72, -, 150, 50, 140, 60, 130, 105, 72, -, 17000, 80, -, 170, 55, 160, 68, 150, 120, 80, -, 20000, 100, -, 190, 60, 180, 75, 165, 130, 88, - All dimensions in mm Proof Load = 2 x S.W.L. (Safe Working Load) Other threads can also be supplied to special order. Shoulder Nut Eye Bolt - Installation for Angular loading The threaded shank must protrude through the load sufficiently to allow full engagement of the nut. If the eye bolt protrudes so far through the load that the nut cannot be tightened securely against the load, use properly sized washers to take up the extra space Between The Nut And The Load Place washers or spacers between nut and load so that when the nut is tightened securely, the shoulder is secured flush against the load surface. Forged Eye Bolt Warning & Applications Important Safety Information - Read & Follow Inspection / Maintenance Safety Never use eye bolt that shows signs of wear or damage Never use eye bolt if eye or shank is bent or elongated. Always be sure threads on shank and receiving holes are clean Never machine, grind, or cut eye bolt. Assembly Safety Never exceed load limits specified in Table I Never use regular nut eye bolts for angular lifts. Always use shoulder nut eye bolts (or machinery eye bolts) for angular lifts. For angular lifts, adjust working load as follows: Never undercut an eye bolt to seat shoulder against the load. Always countersink receiving hole or use washers to seat shoulder. Always screw eye bolt down completely for proper seating. Always tighten nuts securely against the load. Shoulder Nut Eye Bolt - Installation for Angular loading Operating Safety Always stand clear of load Never lift load with steady, even pull - do not jerk. Always apply load to eye bolt in the plane of the eye, not at an angle Never exceed the capacity of the eye bolt. When using lifting slings of two or more legs, make sure the loads in the legs are calculated using the angle from the vertical to the leg and properly size the shoulder nut or machinery eye bolt for the angular load.
Nominal Size of Rope A, B, C, D, E, F, G, H, J, K, L, (1), (2), (3), (4), (5), (6), (7), (8), (9), (10), (11), (12), 08, 22, 38, 13, 34, 54, 09, 04, 3.5, 62, 04, 30, 10, 24, 46, 15, 38, 64, 11, 06, 5.5, 76, 05, 34, 12, 32, 60, 19, 44, 80, 13, 08, 7.5, 90, 06, 44, 14, 32, 60, 21, 44, 80, 15, 08, 7.5, 90, 06, 44, 16, 40, 72, 23, 58, 98, 17, 08, 7.5, 114, 08, 56, 18, 44, 80, 29, 66, 110, 19, 10, 9.5, 125, 08, 60, 20, 50, 94, 31, 74, 124, 21, 12, 11.0, 150, 10, 70, 22, 58, 102, 34, 82, 134, 24, 121, 11.0, 165, 10, 78, 24, 64, 108, 36, 92, 150, 26, 12, 11.0, 176, 10, 84, 25, 70, 118, 37, 108, 162, 27, 14, 13.0, 200, 10, 90, 29, 76, 132, 41, 112, 176, 31, 16, 14.5, 230, 12, 100, 32, 96, 152, 44, 134, 196, 34, 16, 14.5, 250, 12, 120, 35, 104, 174, 48, 152, 228, 38, 19, 17.5, 300, 16, 136, 38, 114, 198, 54, 165, 254, 41, 24, 22.0, 330, 18, 150, 41, 114, 198, 56, 165, 254, 44, 24, 22.0, 330, 18, 150, 44, 125, 222, 57, 178, 285, 47, 26, 23.5, 355, 25, 175, 48, 134, 246, 67, 190, 315, 51, 28, 25.5, 380, 28, 190, 51, 140, 256, 70, 330, 330, 55, 30, 27.5, 400, 28, 196, 54, 140, 256, 70, 200, 330, 58, 30, 27.5, 400, 28, 196, 57, 146, 270, 76, 216, 355, 61, 32, 29.5, 425, 30, 206, 64, 156, 308, 95, 240, 400, 69, 44, 41.0, 450, 32, 220, 70, 200, 400, 120, 275, 500, 75, 60, 57.0, 480, 40, 280, Note, For wire ripes of intermediate size, the next larger size of thimble shall be used., These dimension are minimum for thimblas of nominal size up to and including 41 only
Crosby Fittings Oblong Master Link Item No. W.L.L (tones) Dimensions (mm) N.W IL IW D 8-003-06 1.5 100 60 11 0.2 8-003-0806 3.2 120 70 14 0.4 8-003-1008 4.0 140 80 17 0.7 8-003-13 6.3 160 90 19 1.0 8-003-1310 8.0 160 22 22 1.5 8-003-16 11.5 190 25 25 2.2 8-003-1613 15.0 180 105 28 2.7 8-003-19 17.0 200 120 30 3.5 8-003-2216 20.0 240 140 34 5.1 8-003-26 25.0 250 150 38 7.0 8-003-2619 30.0 250 150 40 8.0
Open Spelter Sockets All Dimensions in mm.