Mist Fan design principle The mist fan was designed with the advanced principle of double atomization. The water drips are jetted under the diffusion of the rotating plate and atomized equipment; reduce the diameter of the atomized water drip to 10 um under the centrifugal force. Hence improve the atomization surface area. The atomized water drips are jetted out with gas flow and it improves the surface speed of liquid greatly, speedup the diffusion of the gas molecule, therefore increase the quantity of the evaporation. Also the evaporation absorbs the heat and decreases the temperature, improves the relative humidity and reduces the dust. Main parts (1) Fan motor (2) Impeller (3) Fan guards (4) Jet plate (5) Water tank (6) Pump (7) Standing pole (Ground) (8) Push pedestal (Ground) (9) Switch box (Wall) Parameter (1) Dimension: 650 mm (26inches) (2) Voltage: 220 ~ 240V (3) Fan height: adjustable from 1700mm to 2000mm (4) Fan oscillation adjustable: 90 degrees automatically (5) Fan tilt adjustable: 30 degrees (6) Available area: 50 square meters (7) Temperatures drop: 4 íµ- 8 íµ (8) Operation Temperature: 20 íµ- 80 íµ (9) Operation Humidity: 20% - 85% (10) Quantity of atomization: 0 - 8L/h (11) Diameter of atomized drip:ú+10 um (12) Capacity(Ground): 38 L (13) Jet distance: 8 m (14) G.W: 25.4KG; CBM: 0.19M3 Characteristics (1) Thin atomized water drips, long range of spraying, no water dropping. (2) No special demand of the quality of the water and water pressure. (3) Single used, fine enginery, more agile, wide range of using. (4) Easy to install, convenient to move. (5) 90 degrees oscillation, three speed control, blowing without atomization. (6) Waterproof electric design, safe use (7) Adjustable misting volume, low noise Application The atomized fan was widely used in the public situation without air-condition such as store, wine floor, plant, mill, medicine shop, hothouse canopy, fowl house, fungus planting, tea processing where need ventilation, reducing heat and improving humidity. Advantage (1) Compared with the foreign product, we adopt the high quality material---rustproof steel, overcome the problem of dirty forming and cleaning. (2) Compared with the atomized system with nozzle and plenum pump, our fan can't be blocked and without high pressure. (3) No need to maintenance, saving power and water, with lower cost, compared with the system with central air-condition and jet house. (4) Overcome the disadvantage of large air resistance and slow reduction of temperature compared with the system of wet shade. We can also supply: (1) Mist fan AM-650GH; (2) Mist fan AM-650GB; (3) Mist fan AM-650GT; (4) Mist fan AM-650W; (5) Mist Fan AM-702F20 It include four boxes: (1)Box 1:POLE 125CM*8CM*15CM (2)Box 2:WATER TANK 47CM*42CM*43CM (3)Box 3:GUARDS AND IMPELLER 72CM*72CM*7CM (4)Box 4:FAN MOTOR,PUSH PEDESTAL,JET PLATE,WATER PUMP 72CM*52CM*20CM
Wall Mist Fan design principle The mist fan was designed with the advanced principle of double atomization. The water drips are jetted under the diffusion of the rotating plate and atomized equipment; reduce the diameter of the atomized water drip to 10 um under the centrifugal force. Hence improve the atomization surface area. The atomized water drips are jetted out with gas flow and it improves the surface speed of liquid greatly, speedup the diffusion of the gas molecule, therefore increase the quantity of the evaporation. Also the evaporation absorbs the heat and decreases the temperature, improves the relative humidity and reduces the dust. Main parts (1) Fan motor (2) Impeller (3) Fan guards (4) Jet plate (5) Water tank (6) Pump (7) Switch box (Wall) Parameter (1) Dimension: 650 mm (26inches) (2) Voltage: 220 ~ 240V (3) Fan height: adjustable from 1700mm to 2000mm (4) Fan oscillation adjustable: 90 degrees automatically (5) Fan tilt adjustable: 30 degrees (6) Available area: 50 square meters (7) Temperatures drop: 4 íµ- 8 íµ (8) Operation Temperature: 20 íµ- 80 íµ (9) Operation Humidity: 20% - 85% (10) Quantity of atomization: 0 - 8L/h (11) Diameter of atomized drip: < 10 um (12) Capacity(Wall): 10 L (13) Jet distance: 8 m (14) G.W: 17.1KG; CBM: 0.093M3 Characteristics (1) Thin atomized water drips, long range of spraying, no water dropping. (2) No special demand of the quality of the water and water pressure. (3) Single used, fine enginery, more agile, wide range of using. (4) Easy to install, convenient to move. (5) 90 degrees oscillation, three speed control, blowing without atomization. (6) Waterproof electric design, safe use (7) Adjustable misting volume, low noise Application The atomized fan was widely used in the public situation without air-condition such as store, wine floor, plant, mill, medicine shop, hothouse canopy, fowl house, fungus planting, tea processing where need ventilation, reducing heat and improving humidity. Advantage (1) Compared with the foreign product, we adopt the high quality material---rustproof steel, overcome the problem of dirty forming and cleaning. (2) Compared with the atomized system with nozzle and plenum pump, our fan can't be blocked and without high pressure. (3) No need to maintenance, saving power and water, with lower cost, compared with the system with central air-condition and jet house. (4) Overcome the disadvantage of large air resistance and slow reduction of temperature compared with the system of wet shade. We can also supply: (1) Mist fan AM-650GH; (2) Mist fan AM-650GB; (3) Mist fan AM-650GT; (4) Mist fan AM-650C; (5) Mist Fan AM-702F20 It include four boxes: (1)Box 1:POLE 125CM*8CM*15CM (2)Box 2:WATER TANK 47CM*42CM*43CM (3)Box 3:GUARDS AND IMPELLER 72CM*72CM*7CM (4)Box 4:FAN MOTOR,PUSH PEDESTAL,JET PLATE,WATER PUMP 72CM*52CM*20CM
Air Cooler design principle The mist fan was designed with the advanced principle of double atomization. The water drips are jetted under the diffusion of the rotating plate and atomized equipment; reduce the diameter of the atomized water drip to 10 um under the centrifugal force. Hence improve the atomization surface area. The atomized water drips are jetted out with gas flow and it improves the surface speed of liquid greatly, speedup the diffusion of the gas molecule, therefore increase the quantity of the evaporation. Also the evaporation absorbs the heat and decreases the temperature, improves the relative humidity and reduces the dust. Main parts (1) Fan motor (2) Impeller (3) Fan guards (4) Jet plate (5) Water tank (6) Pump (7) Standing pole (Ground) (8) Push pedestal (Ground) (9) Switch box (Wall) Parameter (1) Dimension: 650 mm (26inches) (2) Voltage: 220 ~ 240V (3) Fan height: adjustable from 1700mm to 2000mm (4) Fan oscillation adjustable: 90 degrees automatically (5) Fan tilt adjustable: 30 degrees (6) Available area: 50 square meters (7) Temperatures drop: 4 íµ- 8 íµ (8) Operation Temperature: 20 íµ- 80 íµ (9) Operation Humidity: 20% - 85% (10) Quantity of atomization: 0 - 8L/h (11) Diameter of atomized drip: < 10 um (12) Capacity (Ground):38 L (13) Jet distance: 8 m (14) G.W: 24.4KG; CBM: 0.118M3 Characteristics (1) Thin atomized water drips, long range of spraying, no water dropping. (2) No special demand of the quality of the water and water pressure. (3) Single used, fine enginery, more agile, wide range of using. (4) Easy to install, convenient to move. (5) 90 degrees oscillation, three speed control, blowing without atomization. (6) Waterproof electric design, safe use (7) Adjustable misting volume, low noise Application The atomized fan was widely used in the public situation without air-condition such as store, wine floor, plant, mill, medicine shop, hothouse canopy, fowl house, fungus planting, tea processing where need ventilation, reducing heat and improving humidity. Advantage (1) Compared with the foreign product, we adopt the high quality material---rustproof steel, overcome the problem of dirty forming and cleaning. (2) Compared with the atomized system with nozzle and plenum pump, our mist fan can't be blocked and without high pressure. (3) No need to maintenance, saving power and water, with lower cost, compared with the system with central air-condition and jet house. (4) Overcome the disadvantage of large air resistance and slow reduction of temperature compared with the system of wet shade. We can also supply: (1) Mist fan AM-650GH; (2) Mist fan AM-650GT; (3) Mist fan AM-650W; (4) Mist fan AM-650C; (5) Mist fan AM-702F20 It include four boxes: (1)Box 1:POLE 125CM*8CM*15CM (2)Box 2:WATER TANK 47CM*42CM*43CM (3)Box 3:GUARDS AND IMPELLER 72CM*72CM*7CM (4)Box 4:FAN MOTOR,PUSH PEDESTAL,JET PLATE,WATER PUMP 72CM*52CM*20CM
Mist Fans Mist Fan (AM-650GB) Mist Fan design principle The mist fan was designed with the advanced principle of double atomization. The water drips are jetted under the diffusion of the rotating plate and atomized equipment; reduce the diameter of the atomized water drip to 10 um under the centrifugal force. Hence improve the atomization surface area. The atomized water drips are jetted out with gas flow and it improves the surface speed of liquid greatly, speedup the diffusion of the gas molecule, therefore increase the quantity of the evaporation. Also the evaporation absorbs the heat and decreases the temperature, improves the relative humidity and reduces the dust. Main parts (1) Fan motor (2) Impeller (3) Fan guards (4) Jet plate (5) Water tank (6) Pump (7) Standing pole (Ground) (8) Push pedestal (Ground) (9) Switch box (Wall) Parameter (1) Dimension: 650 mm (26inches) (2) Voltage: 220 ~ 240V (3) Fan height: adjustable from 1700mm to 2000mm (4) Fan oscillation adjustable: 90 degrees automatically (5) Fan tilt adjustable: 30 degrees (6) Available area: 50 square meters (7) Temperatures drop: 4 íµ- 8 íµ (8) Operation Temperature: 20 íµ- 80 íµ (9) Operation Humidity: 20% - 85% (10) Quantity of atomization: 0 - 8L/h (11) Diameter of atomized drip: < 10 um (12) Capacity (Ground):38 L (13) Jet distance: 8 m (14) G.W: 24.4KG; CBM: 0.118M3 Characteristics (1) Thin atomized water drips, long range of spraying, no water dropping. (2) No special demand of the quality of the water and water pressure. (3) Single used, fine enginery, more agile, wide range of using. (4) Easy to install, convenient to move. (5) 90 degrees oscillation, three speed control, blowing without atomization. (6) Waterproof electric design, safe use (7) Adjustable misting volume, low noise Application The atomized fan was widely used in the public situation without air-condition such as store, wine floor, plant, mill, medicine shop, hothouse canopy, fowl house, fungus planting, tea processing where need ventilation, reducing heat and improving humidity. Advantage (1) Compared with the foreign product, we adopt the high quality material---rustproof steel, overcome the problem of dirty forming and cleaning. (2) Compared with the atomized system with nozzle and plenum pump, our mist fan can't be blocked and without high pressure. (3) No need to maintenance, saving power and water, with lower cost, compared with the system with central air-condition and jet house. (4) Overcome the disadvantage of large air resistance and slow reduction of temperature compared with the system of wet shade. We can also supply: (1) Mist fan AM-650GH; (2) Mist fan AM-650GT; (3) Mist fan AM-650W; (4) Mist fan AM-650C; (5) Mist fan AM-702F20 it include four boxes: (1)Box 1:POLE 125CM*8CM*15CM (2)Box 2:WATER TANK 47CM*42CM*43CM (3)Box 3:GUARDS AND IMPELLER 72CM*72CM*7CM (4)Box 4:FAN MOTOR,PUSH PEDESTAL,JET PLATE,WATER PUMP 72CM*52CM*20CM
Oral examine camera Dental camera for tooth watched and beauty-salon Features: 1.This dental camera that enables users to examine their teeth, ears, hair and other body parts on their own, 2.You also could use it to look into cotton fibre, inset, leaf, rock and mini-size eletron element so on. 3.Operation is easy. Just plug the camera cable into any tv video input or computer usb port and aim the lens at the part you want to see. Roughly 26mm wide and 199mm long, this camera uses four aa batteries. It has three types, namely pal/cmos, ntsc/cmos and ccd. 4.All digital signal processing 5.Through the usb integration, clear digital image signal can be transmitted from our sensor 6.Simplifies equipment integration 7.Only handset and usb cable required 8.Wide focusing control ranges from one tooth to full face (far/close distance focus) 9."plug & play" function for ease-of-installation with only usb port connection 10. 13 mm slim head size for easy and comfortable intra oral positioning 11.An unified s/w program for full management and analysis in convenient linkages with other digital devices such as panorama and intra-oral sensor, xxxxx Camera specification: Frequency: ism 2, 400 - 2, 483mhz Imaging sensor: 1/3 inch omnivision color cmos Horizontal resolution: 380tv line Cmos total pixels: 628 x 582 (pal) / 510 x 492 (ntsc) View angles: 62 degrees Minimum illumination: 0.5lux / f1.5 Gain control: automatic Transmission power: 10mw Consumption current: 80 ma Modulation mode: fm Bandwidth: 18m Operating range: 30m/100m (obstructed / unobstructed) Power: dc 8v or 9v battery Operating temperature: -10oc ~ +40oc Operating humidity: 85%rh Dimension(w*l*h): 200x20x22 mm Weight:60g Packing: Gift box size : 25x10.8x3.5 cm Carton box size: 43x38x47 cm 1 gift box : 1 unit 1 carton box : 60 sets Gross weight : 17 kg/ Carton paper case
Key-Wound Temperature Chart Recorders are equipped with liquid or air sensors, offer selectable 24-hour or 7-day operation and recording, and have a temperature range of 0�°â??150�°F. MA-80 models are wall-mounted while MA-81 units are portable. No power source or batteries are required for operation. Air sensors have bendable 14-3/8in (365mm) cable and liquid sensors are supplied with 5ft (1.5m) cable. Units include a package of 100 MAA-60 7-Day Charts and a felt-tip pen. Additional 7-Day and 24-Hour Charts for Temperature Recorder, and a package of five MAA-62 Felt-Tip Pens are available separately. Inquire for models with NIST-traceable calibration. Temperature sensors contain mercury and may be restricted for sale in some areas; check local regulations before ordering. Also, inquire for Temperature Recorders in other F or C ranges, and/or electric or battery-operated drives.
Feature: A. The device adopts impulse jet oxygen feeding technique with great flow rate of oxygen feeding in a shot while, when feeding oxygen, it adopts change mode major in reflux and many kinds of gas flow mechanism such as convection, laminar flow, sheet flow and so on concurrently, which is good to increase partial pressure of oxygen rapidly, At the same time fluctuation of thorax caused by increasing oxygen flow into airway is good to let out CO2. B. Jet oxygen feeding is supported by pressure when inspiration and secure certain PEEP effect when feeding oxygen, So as to reach good effectiveness of oxygen feeding. C. Accumulator jar, it can be used while being charged and can last for four hours after having been charged. D. Alarm system with sound and light when lack of electric quantity or airway pressure. E. 300CG chooses digital display of import pressure sensor. F. 300CG has three kinds of airway limited pressure alarm for adult, child and infant. G. The device disposes pressure humidifier which has good humidigying effectiveness. Specifications Power supply:AC220V+22V 50HZ+1HZ I/E ratio·ª1:1,1:1.5+ 1:3 and 3:1 Driving Pressure ·ª0+0.15MPa SIGH:6breaths/min, I/E=1:4 Pressure Regulator Limit:0.30MPa CPAP·ªnot less than 1KPa Oxygen Concentration Adjustable:40%-90% Process Ventilation·ªT=10min,Infinite recursion ProI:f(150):f(35)=7:3 ProII:f(35):f(150)=7:3 Alarm:Alarm with light and sound for no gas or no power or airway pressure is over Inner Battery:4Ah 12V Ventilation Mode:HFJV(High Frequency Jet Ventilation);CPAP(Continuous positive airway pressure),HFJV+SIGH(Sigh); Process ventilation I and Process ventilation II, Manual Control Mode.
Feature It is a ventilation device for infant with novel structure and good performance, and chooses opening ventilation mode with high frequency and little tidle volume, so the airway pressure is low.If you want to know more. A. The tidal air can letout with constant pressure, constant current or accurately adjustable flow. B. Opening ventilation, opening intubation makes it not need casing bag, little resistance as expiration is suited for the ventilation management of infant. C. Evident effectiveness of treating ards can be shown with inserting small tube and jetting oxygen through nasal vestibule, which is secure and doesn't cause pressure wound easily. D. Peep and humidifier volume can be adjusted accurately. E. Alarm system with sound and light when no oxygen, poor of electric quantity or low airway positive pressure. F. Heated humidifier can be used for good effectiveness of humidifying. G. Accumulator jar, it can be used while being charged and can last for more than four hours. Specifications Frequency10+150 breaths/min I/e ratio1:1, 1:1.5+ 1:3 and inverse ratio Pressure atomizer rate>=6ml/h Process ventilationt=10min, Proi:f(150):f(35)=7:3 Proii:f(35):f(150)=7:3 Storage battery4ah, automatic charge when 12v Sigh:3breaths/min Alarm:alarm when battery voltage is lower than 11v, alarm lasts 6 seconds if no oxygen, alarm with audible signals and flashing light when the airway pressure is over 0.8kpa Cpap0+0.5kpa Peep0+0.20kpa Oxygen concentration adjustable:21%-90% Jetting volume rangeo+600ml/time Ventilation mode:hfjv(high frequency jet ventilation);cpap(continuous positive airway pressure);hfjv+peep(positive end-expiratory pressure), hfjv+sigh(sigh), process ventilation i and process ventilation ii. Standard packaging.
Feature A. The device adopts impulse jet oxygen feeding technique with great flow rate of oxygen feeding in a shot while, when feeding oxygen, it adopts change mode major in reflux and many kinds of gas flow mechanism such as convection, laminar flow, sheet flow and so on concurrently, which is good to increase partial pressure of oxygen rapidly, at the same time fluctuation of thorax caused by increasing oxygen flow into airway is good to let out co2. B. Jet oxygen feeding is supported by pressure when inspiration and secure certain peep effect when feeding oxygen, so as to reach good effectiveness of oxygen feeding. C. Accumulator jar, it can be used while being charged and can last for four hours after having been charged. D. Alarm system with sound and light when lack of electric quantity or airway pressure. E. 300cg chooses digital display of import pressure sensor. F. 300cg has three kinds of airway limited pressure alarm for adult, child and infant. G. The device disposes pressure humidifier which has good humidigying effectiveness. Specifications Power supply:ac220v+22v 50hz+1hz I/e ratio1:1, 1:1.5+ 1:3 and 3:1 Driving pressure 0+0.15mpa Sigh:6breaths/min, i/e=1:4 Pressure regulator limit:0.30mpa Cpapnot less than 1kpa Oxygen concentration adjustable:40%-90% Process ventilationt=10min, infinite recursion Proi:f(150):f(35)=7:3 Proii:f(35):f(150)=7:3 Alarm:alarm with light and sound for no gas or no power or airway pressure is over Inner battery:4ah 12v Ventilation mode:hfjv(high frequency jet ventilation);cpap(continuous positive airway pressure), hfjv+sigh(sigh); process ventilation i and process ventilation ii, manual control mode. Standard packing
PUREXA Instant Teeth Whitening Pen is a teeth whitening gel that uses PAP and HA two innovative ingredients that whiten your teeth without peroxide or sensitivity PUREXA Instant Teeth Whitening Kit is a hydrogen peroxidefree teeth whitener solution that uses Phthalimidoperoxycaproic Acid PAP and Hydroxyapatite HA to break down the stains and restore the natural color of your teeth and teeth cleaner PUREXA Instant Teeth Whitening Pen is formulated with effective ingredients like PAP Sodium Bicarbonate Hydroxyapatite and Aloe Vera that ensure that the product leaves zero sensitivity on the teeth and protects the enamel and gums PUREXA Instant Teeth Whitening Pen is small portable and easy to apply with a precision tip applicator that allows you to target the areas you want to whiten and avoid the areas you dont PUREXA Instant Teeth Whitening Pen is gentle and effective as it can be used daily without discomfort or sensitivity It is suitable for all types of teeth even sensitive ones PUREXA Instant teeth whitener Pen delivers fast results as you can notice a noticeable difference in the brightness of your teeth within just a few minutes of application PUREXA Instant Teeth Whitening or whitener Pen is clinically tested and safe to use providing professionalgrade results as an alternative to expensive dental visits It is also vegan and crueltyfree PUREXA Instant Teeth Whitening Pen eliminates stains caused by coffee wine and other foods as well as tobacco aging and medication It can help you achieve a brighter more confident smile PUREXA Instant Teeth Whitening Pen can be used like a handy cosmetic teeth whitening gel for all important occasions of your life such as weddings parties interviews or dates It can fit in your pocket purse or backpack and you can use it anytime anywhere PUREXA Instant Teeth Whitening Pen is free from peroxide making it a safe and healthy choice for your oral care routine It does not contain any harsh or artificial ingredients that can harm or irritate your teeth and gums
Model E041 1, seating:2 2, size:1980*1100*800mm 3, acrylic shell:blue (without ocf thermal insulation) 4, cover:black (with white foam insulation) 5, skirt: red brown, ps board (with white foam insulation) 6, control system: gd-7005 1set 7, circulating pump:0.35 hp*1 8, heater: 1.5 kw*1 9, massage jets: 18 pcs 10, air jets: 6 pcs 11, water pump: 1 hp*1 12, air pump: 300 w 13, ozone generator: 1 pcs 14, large colorful led bottom light 1 pcs 15, pillows: 2pcs(ka107a=2pcs) 16, air valve: 1 pcs 17, water filter cartridge with paper filter:1 pcs 18, 1.5" suction: grey, 2pcs; drainage: 1pcs 19, electricity:220 v 50hz 20, water capacity: 0.6m 21, common speaker: 2 pcs 22, pop-up fountain:none 23, aromatic box:none 24, watefall:none 25, suttle weigh:193 kgs 1980*1100*800 mm, 193 kgs
Ps-47 Application Sizing of filament yarn Chemistry for performance òexcellent abrasion resistance, adhesion, flexibility properties òno blocking, easy desizing, good hard water solubility òworks at minimum 25% less size pick-up than acrylics òhigher loom efficiency òsuitable for air jet and water jet looms Chemistry for economics òhigher efficiency on loom at lower pick-up òlesser material requirement, smaller storage space and reduced inventory cost Physical properties Form/colour/solid content/ph of solution/solubility: Granular form/dark yellow/100%/5 û 6.5/completely soluble in hot water Guide recipe Ingredients Quantity Ps-47 100 kg Lubricant 1.5 û 2 kg (if required) Size concentration 10 - 12% on ri meter Pickup (without oil) 5 - 5.5% on filament yarn 7- 8% on texturised yarn 25 kg paper bag
Taper button bit is used for hard or very hard rock formation. Excellent quality and durability and specialized heat treat & stress relief also maximum performance and hole cleaning ability. Our button bits made with high quality of raw material through special heat treatment, especially, tungsten carbide tips are import from south africa, widely applied in hand held (short-hole) drilling system for dimensional stone quarrying. Now, we are exporting the huge qty 32mm, 34mm, 40mm for indian quarry and spain, finland quarr 38mm, 41mm is very popular for granite and marble etc quarries.. Diameter of bits from 30mm to 42mm with 4, 6, 7, 11, 12 degree, number of buttons is 4, 5, 6, 7, 8 , 9, 7 buttons is very popular for hand held (short holes ) and blast drilling system.
Motor specifications Mechanic motor 0, 55 kw, 1400 rpm, 0, 75 hp - 7, 3 ampere, 3 phase - single phase // 380 v - 220 v Hydraulic motor 0, 75 kw, 900 rpm, 1 hp - 8, 7 ampere, 3 phase - single phase // 380 v - 220 v Sound level 45 db Hydraulic piston power Total pressure = ðr2 x 160 (working pressure bar) Total pressure = 3, 14* (3, 15 x 3, 15) = 31, 156kg Total pressure = 31, 156 x 160 = 4 984, 96kg Diameter of piston cylinder we used is 63mm which comes to as radius 3, 15 cm. As you have seen above formula you can have 5 tons of total pressure while Working on our rsm2200 / rsm2400 / rsm2600 machines. Standard accessories list 1. 18 pcs rim attaching center 2. 1 pc (mihengir) metal pointer 3. 6 pcs press tips (in different forms) 4. 3 pcs support axis for press tips On standart export pallets
This Unique Rim Straighening Machine is used to straighten and correct all kinds of defected rims from 10" to 22". Dimensions: Height . . . . . . . . . . . . . . . 1250 mm Length . . . . . . . . . . . . . . . 1110 mm Width . . . . . . . . . . . . . . . . 610 mm Net weight . . . . . . . . . . . . . 370 kg. Motor specifications: Mechanic motor. .. . . . . . . . 0,55Kw/ 50Hz / 0, 75 HP, 3 phase-single phase, 220v-380 v Hydraulic motor. . . . . . . . . 0, 75 kw 1400 RPM, 1 HP, 3 phase-single phase, 220v-380 v Sound level. . . . . . . . . . . . . 35 db Standard Accessories List : 1. 18 pcs rim attaching center 2. 1 pcs (mihengir) metal pointer 3. 7 pcs press tips 4. 3 pcs support axis for press tips 5. 1 pcs lever 6. 1 pcs lathe pen 7. 1 pcs upper support 8. 1 pcs lower support 9. 4 pcs support pins 10. Flange nuts and bolts. On standart export pallets: Dimensions Height . . . . . . . . . . . . . . . 1250 mm Length . . . . . . . . . . . . . . . 1110 mm Width . . . . . . . . . . . . . . . . 610 mm Net weight . . . . . . . . . . . . . 370 kg.
The detailed specification of edf r/c plane t50: Material: eps foam Length: 1, 050mm ( 41.33in ) Wingspan: 820mm ( 33.46in ) Height: 380mm ( 14.96in ) Flying weight:: around 1200g Thrust·ªf¦950g Landing gear: electric retract landing gear with gear door system Edf diameter: 70mm , 5 blade Motor: 2650kv brushless motor Esc: 45a brushless esc Servo: 5 x 9g servo Battery: 14.8v 2200mah20c Radio system: 6 ch 2.4g radio systerm The main features of high scale r/c model airplane: 1)6 channel full function radio control(aileron, elevator, rudder, throttle, Retract, canopy) 2)excellent hedgehopping performance; 3)high speed, flying speed at 80mph; 4)flexible to fly with perfect inverted flight, rolls, hoop; 5)one of the best ducted fan jet in the market! 6)steerable nose landing gear 7)rudder helps steer plane on ground on its scale landing gear for easy take off 8)ready to fly in just minutes! 9)super tough, lightweight airframe! 10)perfect appearance and emulation (scale appearance, great attention has been given to details) 11)shock resistant reinforced fuselage and strong wings 12)can take off from ground or hand launched 13)ground take-off can be performed easily 14)excellent flight performance 15)stable inverted flight 16)fuselage with pre-installed electronics, motor, servos, and speed controller 17)superb quality, simply the best rtf jet you can find! 18)fabricated by accurate molds with high fidelity of real airplane 19)one of the best looking jet in the market 20)detailed body structure 21)high roll rate T50 package information: The size of box:960mmx320mmx475mm 2pcs per box. The weight of per box: Arf: 6.2kg; rtf 7.7kg; Arf+radio:7.2kg Arf+battery :6.7kg
The main features of high scale r/c model airplane: 1)6 channel full function radio control(aileron, elevator, rudder, throttle, Retract, canopy) 2)excellent hedgehopping performance; 3)high speed, flying speed at 80mph; 4)flexible to fly with perfect inverted flight, rolls, hoop; 5)one of the best ducted fan jet in the market! 6)steerable nose landing gear 7)rudder helps steer plane on ground on its scale landing gear for easy take off 8)ready to fly in just minutes! 9)super tough, lightweight airframe! 10)perfect appearance and emulation (scale appearance, great attention has been given to details) 11)shock resistant reinforced fuselage and strong wings 12)can take off from ground or hand launched 13)ground take-off can be performed easily 14)excellent flight performance 15)stable inverted flight 16)fuselage with pre-installed electronics, motor, servos, and speed controller 17)superb quality, simply the best rtf jet you can find! 18)fabricated by accurate molds with high fidelity of real airplane 19)one of the best looking jet in the market 20)detailed body structure 21)high roll rate The detailed specification of edf r/c plane t50: Material: eps foam Length: 1, 050mm ( 41.33in ) Wingspan: 820mm ( 33.46in ) Height: 380mm ( 14.96in ) Flying weight:: around 1200g Thrustú¦í²950g Landing gear: electric retract landing gear with gear door system Edf diameter: 70mm , 5 blade Motor: 2650kv brushless motor Esc: 45a brushless esc Servo: 5 x 9g servo Battery: 14.8v 2200mah20c Radio system: 6 ch 2.4g radio systerm T50 package information: The size of box:960mmx320mmx475mm 2pcs per box. The weight of per box: Arf: 6.2kg; rtf 7.7kg; Arf+radio:7.2kg Arf+battery :6.7kg
Used textile machine Tomcel enterprise ltd, was established in 1989.We are specialized in buying and selling all kinds of second hand textile machinery such as : Toyada, tsudakoma, nissun, picanol, vamatex, saure, sulzer, somet, dornier, nuovo pigone weaving loom, rapier loom, air jet loom, water jet loom with dobby, sucker muller, zell, schlafhorst, west point, benninger, tsudakoma sizing machine, wraping machine, sectional wraping machine, murata 33h-33j-33f, barmag afk, fk4, fk5, fk-6 700-900-1000-1200, icbt, sds600-700-900, rpr, ssm, teijon seiki, rieter-scragg draw texturing machine, spinning eqipment : open end rotor spinning complete plant, knitting machine, printing machine, finishing machine and other textile machinery or complete plant and we also mauufacturing and marketing various brand new spare parts and buy.This is our main lion of bussines, we have a good position in our country and have a goood relationship at many country's markets.Please feel free to contact us for more details. We are looking forward to established business relationship with you in the near fulture. Tomcel enterprise ltd., want to selling used textile machine: 1.Sucker sizing machine model:z-150 1990years 1set 2.Kawamoto beaming model: ksd-bm 1980years 1set 3.Kawamoto warping machine model: fw-t1000 1986years 1set 4.Hacoba sectional machine model: usk-t1000 1991years 1set 5yamada .Dobby for water jet loom model:gd30 50pcs 6.Murata twisting machine model 310-c 1991years 8sets 7.Rieter scragg draw texturing machine model: drawest d/d 1995years 2sets 8.Rieter scragg draw texturing machine model: drawset 1997years 5sets 9.Plastic shuttle for textile shuttle change loom 5, 000pcs. Standard packing
Steam room 1) dimensions: 1580*1580*2200mm Volume: 3.35cbm Glass packing size: 1690*940*300mm Basin packing size: 1680*1680*770mm Back panelsize: 1630*1050*410mm N.W: 190kgs G.W: 270kgs Quantity per 20' gp: 8pcs Quantity per 40' gp: 17pcs Quantity per 40' hq: 20pcs 2) material: Acrylic tray with stainless steel shelf Unique aluminumn frame Tempered glass door Commodity name:dignity steam room Features and functions: 1) 3kw steamer 2) control panel: Time/temperature setting and fm radio 3) exhaust fan 1pcs 4) top lamp 1pcs 5) accupuncture jet 6pcs 6) water accessories: Top shower 1pcs Cold /hot water switch system 1set Bathing function switch (shower, jet)1pcs Flexible 8 functions hand shower 1pcs Drainage 1pcs 7) shelf for shampoo and towel 1set 8) seat 1pcs 9) mirror 1pcs 10)foot massage 11)1.5hp pump surfing massage system 12)build-in shower panel(corner jet 6 pcs) 2pcs Optional function: 1.Computer multi-function design With telephone 2.Bubble massage system 3.Indoor television system 4.Water thermostat 5.Submerged lamplight Product origin: china Brand name: isabelle Certificates: iso, ce Price terms: fob, exw, cif, cfr Payment: l/c, t/t Supply ability: 7100 pcs/year Minimum order: Delivery time:2 weeks Packing: plastics foam, cartons, wood crate Plastics foam, cartons, wood crate
Common Name: Chocolate Grouper Alternative Names: Chocolate Hind; Brown Barred Grouper Scientific Name: Cephalopholis Boenak Main Diagnostic Features: Body brown, with 7 or 8 more or less distinct dark bars. Fins dark brown, with a pale blue line at corners of caudal fin. Cooking Tips: Process type: Whole Round Size range: 300/500 gms; 500/1000 gms Packing in bulk / 10 / 15 kgs per box Method of Catch: LHP – Hand Lines & Pole Lines (Hand Operated) Fishing Zone: FAO 051
