Solar Charge Controller Suppliers and Manufacturers

Charge modeïPWM System voltageï12V Charge current: 8A/10A Load output voltage: 12V Battery typeLead acid (GEL, AGM, flooded) Application 1. The household solar power systems 2. Small solar power system 3. The portable solar application products 1.Electronically regulated charging regime: Boost and float charge 2.Emperature compensation 3.Deep discharge protection 4.PWM series regulation, no panel short circuit 5.Fully electronically protected: panel surge voltage, Wrong polarity at panel or battery, Overload and short circuit at load 6.LED indications: Charge status, SOC, LVD, Overload/Short-Circuit Common positive allows grounding

*Product Name: 5A Home Controller(New Style) *Rated Charging Current:5A *Rated Load Current:5A *System Voltage:12V/24V Automatic Identification *Undervoltage Voltage:12.0V; ×2/24V; *Over-discharge Protection Voltage:11V/ 22V *Over-dischargeRecovery Voltage:12.5V/25V *Over Voltage Protection:15.5V/31V *Charge Return Voltage:13.2v ×2/24V *Boost Voltage:14.6V×2/24V (Hold Time10min)(Call it when Only Appear Over-discharge) *Direct Charge Voltage:14.4V; ×2/24V (Hold Time10min) *Float Voltage:13.6V; ×2/24V(Hold TimeDropped to Charge Return Voltage) *Temperature Compensation: -5mv//2VPromote,Direct Charge,Floating Charge,Charging Return Voltage Compensation *No-load Loss:6 mA *Charge Loop Drop:Not More Than0.26V *Discharge Loop Drop:Not More Than 0.15V *Load Overload/Short Circuit Protection:Yes *Control Mode:Hand Switch *Work TemperatureTechnical grade-35 to +55

1. Built-in LED constant current source. 2. With intelligent four phases PWM digital dimming.(power is 100%,75%,50%,25%) 3. IP68 waterproof degree. 4. The max output voltage is 70V, which can drive 20 LED lamps installed in series 5. Various protections. Specification: System voltage: 12V/24V Auto Output current: 330mA ¨C 2310mA No-load loss: 5mA/12V;7mA/24V Solar input voltage: < 55V The Max. charging current: 8A Overvoltage protection: 17.0V; 2/24V Equal charging voltage: 14.6V; 2/24V(25), duration:1h Ascending charging voltage:14.4V; 2/24V(25), duration:2h Float charging voltage: 13.8V; 2/24V (25) Return voltage during charging:13.2V; 2/24V (25) Return voltage for over-discharging:12.5V; 2/24V Over-discharging voltage:11.1V; 2/24V Temperature compensation :-4.0mv//2V; Light-control voltage :Light-control open 5V; light-control close 6V Efficiency of constant current:90% - 96% Current accuracy:+/-2% Light-control judgment time :10min The Max. output voltage:70V Working temperature:-40 to +70; Protection level:IP68 Weight :160g Dimensions ; 825820(mm)(LWH). Package:1pc/box;54pcs/ctn Size: 280*280*220mm.

1. over-load protection 2.short circuit protection 3.reverse discharging protection 4.reverse-polarity protection 5.protection from the lightning strike. 6.under-voltage protection 7.over-charging protection 8.HVD setting when battery stopped working or charging. 9.LVD setting when load under voltage and stop working. 10. battery capacity display SOC 11. Renew setting of load-starting 12. intelligentize of temperature compensation 13.controller is always counting and saving the charging current hours and display on LCD screen. 14. controller is always counting and saving the discharging current hours and display on LCD screen.

The controller is designed for solar dc lighting system, there are several optional working modes, and has two output terminals, with separate time set. Specification: 12v, 12/24v, 5a, 10a, 15a Use mcu and professional software as the control center to fulfill intelligent soc control, protection to overload, outside and insdie short circuit, reverse connection, thunder and lightining, pv panel reverse current, over charge and discharing etc, usd pwm high efficiency charging way and temperature compensation. Industry level production standard, led indication on system condition. The controller pcb is pained with england apl lacquer, its highly moisture-proof As the same above

Solar charge controller Suunny solar charge controller is controlled by cpu, according to the voltage ofbattery, controller will adjust the charge current and decide if to supply the loads electricity. The following is the detailed performance: Generally keep the battery on full voltage condition. Prevent the battery from over-charging. Prevent the battery from over-discharging. Prevent supplying electricity from the battery to solar panels during nights. Reverse polarity protection for battery Reverse polarity protection for solar panels When the current of load exceeds the rated one of controller, the controller will turn into the self-protection state and is automatically locked up, the screen shows overload. Short circuit happens; the controller will turn into the self-protection state and is locked up, the screen show short circuit. Low voltage happens to battery, the controller will automatically separate loads from system. When the voltage of battery goes up, the loads will automatically restart to work. Protection from the lightning strike When controller is normally working, the lcd screen will show new charging current (a dash-before the numeral) , discharging current and voltage of battery every 5 seconds.

Model: mppt5012a-duo (12a) , mppt5025a-duo (25a) Solar charging controllers for camper Charge modemppt System voltage12v Battery numbertwo battery charging ports Battery typegel, lead-acid, agm2, lifepo4 Application 1.For camper, caravan 2.Self-contained solar systems 3.For boat 1. Increased mpp charging current compared with conventional controllers, due to ultramodern controller technology (microprocessor)by 10 % to 30 % (efficiency > 95 %) 2. Switchable characteristic lines of charging for optimum charging of gel/dry fit/agm/fleece or acid/lead-acid, as well aslifepo4 batteries . 3. Two battery charging ports: automatic charging of the main battery or board battery (board i): Support charging and trickle charging (max.1 a) of the vehicle's starter battery (start ii) with overcharge protection 4. Unattended charging: standard protection against overload, overheating, reverse battery and back discharge of the battery(in case of insufficient solar power, such as at twilight, at night etc.). 5. Overcharge protection: reduction of the charging current of the battery in case of excessive solar power and full battery. Immediate recharging in case of power consumption to ensure always the best possible charging state of the battery. 6. Connection for temperature sensor , automatic adaptation of the charging voltage to the battery temperature. Incase Of low outside temperatures, full charging of the weaker battery is improved, and in case of summery temperature sun necessary battery gassing will be avoided. This is highly recommended, if the battery is exposed to strong variations in temperature, such as in the motor compartment. -

Lifepo4 Solar Charge Controller,

24v Solar Charge Controller,MPPT Solar Charge Controller

Diy Solar Charge Controlle

1. Increased MPPT charging current comparedwith conventional controllers, due to ultramodern controller technology (microprocessor)by 10 % to 30 % (efficiency > 95 %) 2. Switchable characteristic lines of chargingfor optimum charging of Gel/dryfit/AGM/fleece or acid/lead-acid, as well asLiFePO4 batteries . 3.MPPT controller Two Battery Charging Ports: Automaticcharging of the main battery or board battery (Board I): Support charging and trickle charging (max.1 A) of the vehicle's starter battery (Start II) with overcharge protection 4. Unattended Charging: Standard protectionagainst overload, overheating, reverse battery and back discharge of the battery(in case of insufficient solar power, such as at twilight, at night etc.). 5. Overcharge protection: Reduction of thecharging current of the battery in case of excessive solar power and full battery. Immediate recharging in case ofpower consumption to ensure always the best possible charging state of the battery. 6. Connection for temperature sensor ,Automatic adaptation of the charging voltage to the battery temperature. Incase of low outside temperatures, full chargingof the weaker battery is improved, and in case of summery temperaturesunnecessary battery gassing will be avoided. This is highly recommended, if the batteryis exposed to strong variations in temperature, such as in the motor compartment

We're offering solar charge controller. -

Product introduction: 1, solar street light controller can automatically adapt to 12V and 24V systems. 2. It has a dual-period control function (lit at night and before dawn) to meet the individual needs of customers for street lamps. 3. There are three kinds of load power supply modes: pure light control, light control on + delay off (single time), light control on + delay off - delay on + light control off (double time). 4. The dual-period solar street light controller adopts intelligent machine design. All work processes are controlled by software and can achieve high precision and high reliability. 5, using high-efficiency PWM charging technology, with high-precision temperature compensation. 6. The digital tube displays the operating parameters of the LED lamp. 7, with overcharge, over discharge, electronic short circuit, overload protection, anti-reverse and other full electronic protection. 8, the whole machine adopts full potting process, waterproof rating IP68.

Application: Repower c series solar charge controller is designed for solar system application, it can charge the battery intelligently in the daytime, and discharge to offer 24-hour current in dc system.Or control the system output time manually, the Pwm Sdpc-sp-40a Pwm Sdpc-sp-50a Pwm Sdpc-sp-60a Pwm Rated charge current 30a 40a 50a 60a Rated load current 30a 40a 50a 60a Work voltage 12v; 12/24v auto Over load, short circuit protection 1.25 rated load current 60sec, 1.5 rated loads current 5sec, over load protection action. ¡ý3 rated load current short circuit protection action. No load current ¡ü6ma Charging circuit voltage drop ¡ü0.26 v Load circuit voltage drop ¡ü0.15 v Over voltage protection 17v; ¡á2/24v Work temperature Industry stage:-35¡ãc to +55¡ãc; Boost charge voltage 14.6v;¡á2/24v; (keep 10min) Direct charge voltage 14.4v; ¡á2/24v; (keep 10min) Float charge voltage 13.6v; ¡á2/24v; Charge return voltage 13.2v;¡á2/24v; Temperature compensation -5mv/¡ãc/cell (boost charge, direct charge, float charge, charge return voltage); Lower voltage indicate Size:185*105*55mm Weight:1.32kg

PWM dimming series (SR-LP) 1. PWM digital dimming technology. 2. Can support 8 sessions dimming. 3. Double digital LED display and key. 4. PWM dimming indication. 5. Use combine with the constant current source. 6. The full power and half power working time can be set separately. 7. Various protections Parameter: Model: SR-LP series rated charging current: 5A ,10A ,15A ,20A Rated discharging current: 5A ,10A ,15A ,20A Working Voltage: 12V ,24V ,12V/24V Auto No load losses:

PWM Frequency: 40 K Hz Solar Panel Maximum open circuit voltage: 25 volts. Charge control Efficiency: Greater than 85 %. Ambient Temperature: 0- 40 C. Storage Temperature: 0-80 C. Charge Controller Dimensions: 100 X 83 mm. Protections: Battery over charge Protection Battery deep discharge Protection PV reverse voltage Protection Battery reverse voltage polarity protection Load ON/OFF: In the CC left corner there's a jumper. If the jumper is plugged in the Load will turn OFF. If the jumper is plugged out Load will turn ON Indications: Red LED: Indicates Battery low Green LED: Indicates Charging and Battery full. Yellow LED: Indicates Load ON/OFF

Max Solar Panel Voltage - 50V Max Charging Current - 10A Charger Type - PWM L*B*H - 100*105*35 Housing - Metal

Max Solar Panel Voltage - 50V Max Charging Current - 15A Charger Type - PWM L*B*H - 100*105*35 Housing - Metal