5x-5 fine seed cleaner Introduction The 5x series seed cleaner is a universal machine well suited for pre- and fine cleaning many different species of grain and seeds. The standard design of the machine is provided with both pre- and after suction units. Quick screen changing from pre-cleaning into fine cleaning by the operator serves to optimize the cleaning tasks. The 5x series seed cleaner is a very competitive machine, both as regards price and capacity as well as function and operation. Features Easy and quick operation and screen changing The screen boxes are made of wear resistant plywood, which is approved for food Screen cleaning with special rubber balls Built-in light. Durable surface of the machine owing to high-quality powder lacquering Advantages Multiple sieves are reverse configuration, centralized dropping and good for removing the large and small impurity. Positive and negative double wind system are interactive configuration, cleaning impurity up and down twice , good effect for removing light impurity and bad , mold , injured seed . According to the processing need, it can make the screen sets different combination. So it's processing targeted. Up and down screen box reverse configuration, good self- balanced. Screen body and light impurity removing and feed components are made of high quality wooden parts, good sealing and vibration absorbing performance. The noise is low. The wide range of parameter adjustment, convenient adjustment, easy to achieve fine cleaning processing. Adopting the whole steel frame, rubber ball sieve cleaning device, clogging cleaning is effective. All moving parts are equipped with safety protection device, the safety protection is good; Screen body adopt box structure, can effectively reduce the processing workshop dust content. The left and right sides is symmetrical design, discharge system can be left and right exchanged conveniently to can meet different users requirement.
Specifications: 1adopts the iternational most advanced plc control technology. 2.It can perform the forward and backward winding and counting operation, Power failure protection, wire disconnection protection, stop brake, setup Of winding position, location and fault prompt. 3.It can set the procedures and display the operation state through the Touch panel. 4.It,s english interface can properly display the wire diameter, rotatin Speed, number of turns and nunber of layers. 5.Its main sharft control adopts the frequencyconversion stepless speed Adjustment, with the characteristics of short driving chain, large driving Torque, wide speed adjustment range, low noise. 6.It,s speed control has two modes, automatic setup and foot switch speed Adjustment. 7.It,s wire arranging operation is finished by the stepping motor and Highprecision ballspline, the control precision can reach as high as 0.001mm. 8.The counting operation adopts the lighgrid rotary encoder, the output Rotation speed and angle signal are traced with the data. 9.The tension controller employs the west germany damping device, so as to The wire easy disconnection or coul loosing and dropping for the gension Unbalance and easy fluctuation. Features: Simple operation Low noisy Reliable system operation Complete function Wide application range Compact structure High winding precision Long life service Yr260j/360j can adjust the processing range with the iron core and framework size. Through changing the different clapm.It can wind the coils of various Casting pts, it's necessary winding equipment for producin gthe pts with Rshaped enclosed iron core, also the preferred electric engineering Equipment in the pt industy.
Product Code Product Description PRS-ZE0095 Dynamic Cone Penetrometer (DCP) STANDARDS : The PRS-ZE0095 Dynamic Cone Penetrometer is used for the rapid, in situ measurement of structural properties of existing road pavement constructed with unbound materials. it incorporates an 8 kg weight dropping through a height of 575 mm and 60° cone having a diameter of 20 mm. with the standard DCP measurements can be made down to a depth of approximately 850 mm or when extension shafts are used to a recommended maximum depth of 2 m. Readings are usually taken after a set number of blows, changing the number according to the strength of the layer being penetrated. A typical test takes only a few minutes, therefore the instrument provides a very efficient method of obtaining information that would normally require the digging of test pits. The penetration hammer assembly consists of 8 kg hammer, hammer shaft, anvil with plastic plate coupling for ruler and handle. The Dynamic Cone Penetrometer is supplied complete with; � A hammer assembly, � Penetration rod, � 2 piece 60° cone, � Metal plate coupling for ruler, � Segmented adaptor for extension rods, � Segmented upper extension rod, � Segmented lower extension rod, � 2 piece 13-17mm AF spanners, � 3mm AF hex wrench, � Tommy bar, � A bottle of adhesive,10cc, � Users Manual � Steel ruler, � Carrying Case, heavy-duty wooden
ModelMachine Jaguar F10 Heating System Number of heating zones Up 10/ bottom 10 Number of cooling zones 2 Length of heating zones 3700mm Heating mode Hot air Cooling Mode Forced air cooling Exhaust Volume 10m³/min * 2 exhausts Conveyor System Max. Width of PCB 400mm Mesh belt width 450mm Transmission Direction Lâ??R(option: Râ??L) Transmission Net Height 900±20mm Transmission type Mesh and chain Range of rail width 50-400mm Conveyor speed 0-2000mm/min Auto/manual Lubrication Standard Fixed rail side Front rail fixed(option: rear rail fixed) Components high Top and bottom 25m Control system Power supply 5 line 3 phase 380V 50/60HZ Total power 58KW Starting power 50KW Normal power consumption 10KW Warming time 20 mins Temp. setting range From room temp. To 300â?? Temp. control method PID close loop control & SSR driving Temp. control precision ±1â?? Temp. deviation on PCB ±2â?? Data storage Process Data and status storage(80GB) Nozzle plate Aluminum Alloy Plate Abnormal Alarm Abnormal temperature (extra-high/extra-low temperature) Board dropped alarm Tower light: Yellow-warming, Green-normal, Red-abnormal General Dimension(L*W*H) 5400*1320*1490mm Weight 2300kg Color Computer gray
Model JAGUAR A8 Heating System Number of heating zones UP 8/BOTTOM 8 Number of cooling zones 1 Length of heating zones 2800MM Heating mode Up:hot air; bottom: IR Cooling Mode Force air Conveyor System Max. Width of PCB 350mm Mesh belt width 400mm Transmission Direction Lâ??R(or Râ??L) Transmission Net Height 880±20mm Transmission type Mesh Conveyor speed 0-1000mm/min Fixed rail side Front rail fixed(option: rear rail fixed) Control system Power supply 5 line 3 phase 380V 50/60Hz Total power 38kw Starting power 34kw Normal power consumption 4KW Warming time About 20 mins Temp. setting range Room temperature-300â?? Temp. control method PID close loop control & SSR driving Temp. control precision ±1â?? Temp. deviation on PCB ±2â?? Data storage Process Data and status storage(80GB) Nozzle plate Aluminum Alloy Plate Abnormal Alarm Abnormal temp. (extra-high/extra-low temp.) Board dropped alarm Tower light:Yellow-warming, Green-normal, Red-abnormal General Dimension(L*W*H) 4200Ã?700Ã?1320mm Weight 800KG Color Computer gray
Electronic waste disposal equipment , electrical and electronic waste recycling equipment, electronic waste recycling Electronic waste, also known as e-waste, refers disused electronic equipment A wide range of e-waste can be divided into two categories, one is contained in the species is relatively simple, less harmful to the environment of waste electronic products, such as refrigerators, washing machines, air conditioners and other household appliances as well as medical, research and other electrical appliances dismantling and disposal of such products is relatively simple, the other is contained in the material is more complex, relatively large damage to the environment of waste electronic products, such as computers, tv picture tubes in the lead, computer components contain arsenic, mercury and other harmful substances, the phone's raw material of arsenic, cadmium, lead and many other durable drop and bioaccumulative toxic substances. E-waste recycling equipment is mainly used for various electrical appliances, electronic equipment, including refrigerators, air conditioners, washing machines, television sets and other household appliances and electronic products, computer communications, the process from feeding to sorting end, full automatic operation, only 1-2 man operation, the process is physically separated dry without heating, burning, drink chemical raw materials, low cost, high efficiency, no pollution of any separate dry at room temperature, this technique for my company registered patent, numbers are: 200820148816.9 200820148815.4 and 200810141173.X. Promises: the company sells electronic waste disposal equipment have perfect service, one year warranty and lifetime maintenance, completely solve your worries, please rest assured purchase! Electronic waste disposal equipment , electrical and electronic waste recycling equipment, electronic waste recycling
This tracker should be used with iTracing, an app downloaded from App Store/Google Play and pair it to your phone via Bluetooth Anti-loss: chain the tracker with anything you may lose, press ALERT on your mobile app/apk to search the tracker within active distance Remote control: by remote control, you can turn on the cell phone record function or the remote camera shutter function for selfie self-portrait Locate the parking site on map before leaving from your car, help you trace back no matter how far you go away. Compact and lightweight, handy like a key ring, and you can pair up to 8 trackers simultaneously to a phone Product Descriptions: The tracker keeps in connection with your phone through the app iTracing, and you will be informed when they move out of effective distance range. It can protect your kids, seniors, pets, phone, wallet, baggage and laptop from being stolen or lost. By enabling the location tracking feature, the app can also track the location where you last saw the tracker. You can set your preference in the app, such as tracker sensitivity, sound types, and alarm volume. The tracker can also provide a last seen pin-drop on map to help you recover your items and search your cars in parking site. Specifications: 1. Bluetooth version: Bluetooth 4.0 Low Energy 2. Compatible Phone: For iPhone4S/5/5S/5C, for iPad Mini, for iTouch 5, for iPad 3/4, for iPad Air and for Andriod system with Bluetooth 3. 4.0 Smartphone Andriod 4.3 version and up-grade version 4. Working distance: About 75 Feet (without barrier ) 5. Suitable for: Wallet, Car, Kid, Pets, Bags,Suitcase or other belongings. 6. Battery : CR2032 Lithium Coin Battery 7. Standby time: 6 month 8. Net Weight: 9 gram 9. Available colors: Black/White/Green/Red 10. Certificates: CE/ROHS/EPL 11. App Name: iTracing (Free of charge) 12. Connects up to 10 iTag unit 13. App language: English, Chinese, French, Spanish Package contents: 1 anti-lost tracker 1 battery(CR2032) 1 user manual Usage: Please download the APP according Manual, Pressing the product for 3 seconds and you will hear two Beep" sound, which is starting The use of APP search connection product equipment then can be used. Test: If the distance is too short to lose track, you can set the APP inside the Near, Middle and Far, the three options. GPS test can be used but location maybe has Slight error
1.Introduction: Wellhead Wireline Pressure Control Equipment is used for testing and paraffin treatment in flowing oil well, gas well, water injection well and coalbed methane testing. The unit supplies buffer and transitional area for string running with pressure to hole, could satisfy the wellhead seal requirement and there is no overflow. Simple operating, safe and reliable function. Working pressure is 10MPa, 21MPa, 35MPa, 70MPa and 105MPa. Standard ID is 30mm, 52mm, 62mm (65mm), 76mm(78mm), 89mm, 102mm(103mm), 120mm, 140mm, 160mm and 180mm. Our factory has the ability to design products to adapt to different environment according to clients ' requirements. The whole Wellhead Wireline Pressure Control Equipment is composed of Grease Injection Control Head, Top Catcher, Lubricator, Bottom Catcher (include testing blowout assly), BOP, Pump-in Tee, Up sheave, Down sheave, Crossover Flange, Quick testing Assly, all kinds of pipes and other components which necessary. 2.Features and Benefits: 1.Grease Injection Control Head is operated by remote hydraulic manual pump, which could seal wellhead in time and promise safety of operation. A lube oil cup mounted on top of Grease Injection Control Head, which is as lubricator for downing cable and assistant for setting tools in well. 2.Top and Bottom Catcher is double safe feature, in order to prevent string tools dropping in well. Top Catcher is by hydraulic remote control, Bottom Catcher has manual operation system if hydraulic system is fault. There is pressure testing blowout sub, which for checking wellhead pressure, releasing left pressure in Lubricator and pressure self-check. 3.Lubricator supplies buffer and transitional area for string tools, which connected by many Union Lubricators. Single Lubricator is 0.8â??3m, the number of lubricator and total length could be decided by operation. Titanium alloy Lubricator is much better quality and lightweight than normal steel materials. 4.BOP could be separated by Single, Dual, Triple and Quad Ram. Hydraulic or Manual control. 5.There is antifreeze& unfreeze and pressure self-check system. 6.Quick testing Assly could improve the safety of BOP, then avoid the second pressure self-check. 7.Up& Down sheave is selected of Aluminium alloy, and has the function of preventing cable jump. 8.Transport and Storage Frame could accommodate full set of Pressure Control Equipments. Has the ability of designing and producing as requirements. 9.According to different service conditions, our factory supply HP/HT Wellhead Wireline Pressure Control Unit with H2S&Acid services.
Product Description Detailed Product Description: Automatic Trip Hammer is produced as per BS1377: Part9:1990 for carrying out the Standard Penetration Test (SPT). The Automatic Trip Hammer comprises following parts: a) A weight made of steel and provided with an axial hole with a diameter which is 3 mm to 4 mm larger than that of the guide rod. It is of 63.5 kg. b) A pick-up and release mechanism to ensure that the weight has a free fall of 760 mm and shall not influence the acceleration and deceleration of the weight or the rods. c) An inner guide shaft to permit the weight to drop with minimal resistance, and to ensure the weight strikes the anvil squarely. d) An anvil made of steel with an integral threaded portion to connect squarely and rigidly on to the top of the uppermost extension rod. In order to carry out the Standard Penetration Test (SPT) to BS 1377:Part 9:1990. The Auto Trip Hammer, SPT Drive Rods and a Split Tube Sampler are worked together. Technical Parameters The basic operation of the complete set Standard Penetration Equipment are like the following sketch shows. Description of goods: SPT Split Tube Sampler is for doing the Standard Penetration Test (SPT). We manufacture it according to BS 1377: Part 9: 1990. A Top ball valve Adaptor, a pair of Split Spoons, and an open SPT Shoe compose a complete set of SPT Sampler. Both plastic type and steel type basket retainers are available. The ball valve adaptor prevents sample from being washed out of the sampler when the sampler is withdrawn from the borehole. A 60 degree nose cone and long solid rod with 60 degree point are available as well. The screw connection on the top adaptor depends on the type of drill rods being used to drive the sampler, but is most frequently 1.1/2" B.S. Whitworth, NWY Rod, BW or AW Rod. Split Spoon compose of Sample Spoon Head, Split Tube, SPT Adaptor, SPT Shoe. The standard Split Tube Sampler is 2" (50.8 mm) OD x 1.3/8" (34.9 mm )ID x 18" (457mm)/ 24" (610 mm) long. For heavy driving conditions, the Heavy-duty "Tuflok" design is available. Components: 1. Ball Valve Adaptor 2. SPT Solid Rod 3. SPT Nose Cone (2). Split Tubes (3). Basket Retainer (4). SPT shoe
1.Introduction: Wellhead Wireline Pressure Control Equipment is used for testing and paraffin treatment in flowing oil well, gas well, water injection well and coalbed methane testing. The unit supplies buffer and transitional area for string running with pressure to hole, could satisfy the wellhead seal requirement and there is no overflow. Simple operating, safe and reliable function. Working pressure is 10MPa, 21MPa, 35MPa, 70MPa and 105MPa. Standard ID is 30mm, 52mm, 62mm (65mm), 76mm(78mm), 89mm, 102mm(103mm), 120mm, 140mm, 160mm and 180mm. Our factory has the ability to design products to adapt to different environment according to clients ' requirements. The whole Wellhead Wireline Pressure Control Equipment is composed of Grease Injection Control Head, Top Catcher, Lubricator, Bottom Catcher (include testing blowout assly), BOP, Pump-in Tee, Up sheave, Down sheave, Crossover Flange, Quick testing Assly, all kinds of pipes and other components which necessary. 2.Features and Benefits: 1.Grease Injection Control Head is operated by remote hydraulic manual pump, which could seal wellhead in time and promise safety of operation. A lube oil cup mounted on top of Grease Injection Control Head, which is as lubricator for downing cable and assistant for setting tools in well. 2.Top and Bottom Catcher is double safe feature, in order to prevent string tools dropping in well. Top Catcher is by hydraulic remote control, Bottom Catcher has manual operation system if hydraulic system is fault. There is pressure testing blowout sub, which for checking wellhead pressure, releasing left pressure in Lubricator and pressure self-check. 3.Lubricator supplies buffer and transitional area for string tools, which connected by many Union Lubricators. Single Lubricator is 0.8â??3m, the number of lubricator and total length could be decided by operation. Titanium alloy Lubricator is much better quality and lightweight than normal steel materials. 4.BOP could be separated by Single, Dual, Triple and Quad Ram. Hydraulic or Manual control. 5.There is antifreeze& unfreeze and pressure self-check system. 6.Quick testing Assly could improve the safety of BOP, then avoid the second pressure self-check. 7.Up& Down sheave is selected of Aluminium alloy, and has the function of preventing cable jump. 8.Transport and Storage Frame could accommodate full set of Pressure Control Equipments. Has the ability of designing and producing as requirements. 9.According to different service conditions, our factory supply HP/HT Wellhead Wireline Pressure Control Unit with H2S&Acid services.
BMM series motor are small volume,economical type,which is designed with shaft distribution flow, which adapt the Gerotor gear set design and provide compact volume,high power and low weigth. Characteristic features: * Advanced manufacturing devices for the Gerotor gear set, which provide small volume, high efficiency and long life. * Shaft seal can bear high pressure of motor of which can be used in parallel or in series. * Advanced construction design, high power and low weight. Main specification type BMM8 BMM12 BMM20 BMM32 BMM40 BMM50 displacement 8.2 12.9 19.9 31.6 39.8 50.3 Max speed(rpm) rated 1537 1256 814 513 452 358 Cont. 1950 1550 1000 630 500 400 int. 2450 1940 1250 800 630 500 Max Torque (N*M) rated 8 13 19 31 37 33 Cont. 11 16 25 40 45 46 int. 15 23 35 57 70 88 peak 21 33 51 64 82 100 Max speed (kw) rated 1.3 1.7 1.7 1.7 1.7 1.2 Cont. 1.8 2.4 2.4 2.4 2.2 1.8 int. 2.6 3.2 3.2 3.2 3.2 3.2 Max pressure drop(MPa) rated 9 9 9 9 8.5 6 Cont. 10 10 10 10 9 7 int. 14 14 14 14 14 14 peak 20 20 20 16 16 16 Max flow(L/min) rated 14 18 18 18 20 20 Cont. 18 20 20 20 20 20 int. 20 25 25 25 25 25 Weight(kg) 1.9 2 2.1 2.2 2.3 2.4 Type Max.inlet pressure BMM8-50 Cont. 17.5 (Mpa) Int. 22.5 * Continuous pressure:Max. value of operating motor continuously. * Intermittent pressure :Max. value of operating motor in 6 seconds per minute. * Peak pressure:Max. value of operating motor in 0.6 second per minute.
BMM series motor are small volume,economical type,which is designed with shaft distribution flow, which adapt the Gerotor gear set design and provide compact volume,high power and low weigth. Characteristic features: * Advanced manufacturing devices for the Gerotor gear set, which provide small volume, high efficiency and long life. * Shaft seal can bear high pressure of motor of which can be used in parallel or in series. * Advanced construction design, high power and low weight. Main specification type BMM8 BMM12 BMM20 BMM32 BMM40 BMM50 displacement 8.2 12.9 19.9 31.6 39.8 50.3 Max speed(rpm) rated 1537 1256 814 513 452 358 Cont. 1950 1550 1000 630 500 400 int. 2450 1940 1250 800 630 500 Max Torque (N*M) rated 8 13 19 31 37 33 Cont. 11 16 25 40 45 46 int. 15 23 35 57 70 88 peak 21 33 51 64 82 100 Max speed (kw) rated 1.3 1.7 1.7 1.7 1.7 1.2 Cont. 1.8 2.4 2.4 2.4 2.2 1.8 int. 2.6 3.2 3.2 3.2 3.2 3.2 Max pressure drop(MPa) rated 9 9 9 9 8.5 6 Cont. 10 10 10 10 9 7 int. 14 14 14 14 14 14 peak 20 20 20 16 16 16 Max flow(L/min) rated 14 18 18 18 20 20 Cont. 18 20 20 20 20 20 int. 20 25 25 25 25 25 Weight(kg) 1.9 2 2.1 2.2 2.3 2.4 Type Max.inlet pressure BMM8-50 Cont. 17.5 (Mpa) Int. 22.5 * Continuous pressure:Max. value of operating motor continuously. * Intermittent pressure :Max. value of operating motor in 6 seconds per minute. * Peak pressure:Max. value of operating motor in 0.6 second per minute.
BMM series motor are small volume,economical type,which is designed with shaft distribution flow, which adapt the Gerotor gear set design and provide compact volume,high power and low weigth. Characteristic features: * Advanced manufacturing devices for the Gerotor gear set, which provide small volume, high efficiency and long life. * Shaft seal can bear high pressure of motor of which can be used in parallel or in series. * Advanced construction design, high power and low weight. Main specification type BMM8 BMM12 BMM20 BMM32 BMM40 BMM50 displacement 8.2 12.9 19.9 31.6 39.8 50.3 Max speed(rpm) rated 1537 1256 814 513 452 358 Cont. 1950 1550 1000 630 500 400 int. 2450 1940 1250 800 630 500 Max Torque (N*M) rated 8 13 19 31 37 33 Cont. 11 16 25 40 45 46 int. 15 23 35 57 70 88 peak 21 33 51 64 82 100 Max speed (kw) rated 1.3 1.7 1.7 1.7 1.7 1.2 Cont. 1.8 2.4 2.4 2.4 2.2 1.8 int. 2.6 3.2 3.2 3.2 3.2 3.2 Max pressure drop(MPa) rated 9 9 9 9 8.5 6 Cont. 10 10 10 10 9 7 int. 14 14 14 14 14 14 peak 20 20 20 16 16 16 Max flow(L/min) rated 14 18 18 18 20 20 Cont. 18 20 20 20 20 20 int. 20 25 25 25 25 25 Weight(kg) 1.9 2 2.1 2.2 2.3 2.4 Type Max.inlet pressure BMM8-50 Cont. 17.5 (Mpa) Int. 22.5 * Continuous pressure:Max. value of operating motor continuously. * Intermittent pressure :Max. value of operating motor in 6 seconds per minute. * Peak pressure:Max. value of operating motor in 0.6 second per minute.
Bmm hydraulic orbit motors Bmm series motor are small volume, economical type, which is designed with shaft distribution flow, which adapt The gerotor gear set design and provide compact volume, high power and low weigth. Characteristic features: * advanced manufacturing devices for the gerotor gear set, which provide small volume, high efficiency and long life. * shaft seal can bear high pressure of motor of which can be used in parallel or in series. * advanced construction design, high power and low weight. Main specification Type Bmm8 Bmm12 Bmm20 Bmm32 Bmm40 Bmm50 Displacement 8.2 12.9 19.9 31.6 39.8 50.3 Max speed(rpm) Rated 1537 1256 814 513 452 358 Cont. 1950 1550 1000 630 500 400 Int. 2450 1940 1250 800 630 500 Max torque (n*m) Rated 8 13 19 31 37 33 Cont. 11 16 25 40 45 46 Int. 15 23 35 57 70 88 Peak 21 33 51 64 82 100 Max speed (kw) Rated 1.3 1.7 1.7 1.7 1.7 1.2 Cont. 1.8 2.4 2.4 2.4 2.2 1.8 Int. 2.6 3.2 3.2 3.2 3.2 3.2 Max pressure Drop(mpa) Rated 9 9 9 9 8.5 6 Cont. 10 10 10 10 9 7 Int. 14 14 14 14 14 14 Peak 20 20 20 16 16 16 Max flow(l/min) Rated 14 18 18 18 20 20 Cont. 18 20 20 20 20 20 Int. 20 25 25 25 25 25 Weight(kg) 1.9 2 2.1 2.2 2.3 2.4 Type Max.Inlet pressure Bmm8-50 cont. 17.5 (mpa) int. 22.5 * continuous pressure:max. Value of operating motor continuously. * intermittent pressure :max. Value of operating motor in 6 seconds per minute. * peak pressure:max. Value of operating motor in 0.6 second per minute.
Bmm hydraulic orbit motors Bmm series motor are small volume, economical type, which is designed with shaft distribution flow, which adapt The gerotor gear set design and provide compact volume, high power and low weigth. Characteristic features: * advanced manufacturing devices for the gerotor gear set, which provide small volume, high efficiency and long life. * shaft seal can bear high pressure of motor of which can be used in parallel or in series. * advanced construction design, high power and low weight. Main specification Type Bmm8 Bmm12 Bmm20 Bmm32 Bmm40 Bmm50 Displacement 8.2 12.9 19.9 31.6 39.8 50.3 Max speed(rpm) Rated 1537 1256 814 513 452 358 Cont. 1950 1550 1000 630 500 400 Int. 2450 1940 1250 800 630 500 Max torque (n*m) Rated 8 13 19 31 37 33 Cont. 11 16 25 40 45 46 Int. 15 23 35 57 70 88 Peak 21 33 51 64 82 100 Max speed (kw) Rated 1.3 1.7 1.7 1.7 1.7 1.2 Cont. 1.8 2.4 2.4 2.4 2.2 1.8 Int. 2.6 3.2 3.2 3.2 3.2 3.2 Max pressure Drop(mpa) Rated 9 9 9 9 8.5 6 Cont. 10 10 10 10 9 7 Int. 14 14 14 14 14 14 Peak 20 20 20 16 16 16 Max flow(l/min) Rated 14 18 18 18 20 20 Cont. 18 20 20 20 20 20 Int. 20 25 25 25 25 25 Weight(kg) 1.9 2 2.1 2.2 2.3 2.4 Type Max.Inlet pressure Bmm8-50 cont. 17.5 (mpa) int. 22.5 * continuous pressure:max. Value of operating motor continuously. * intermittent pressure :max. Value of operating motor in 6 seconds per minute. * peak pressure:max. Value of operating motor in 0.6 second per minute.
BMM Hydraulic orbit motors BMM series motor are small volume,economical type,which is designed with shaft distribution flow, which adapt the Gerotor gear set design and provide compact volume,high power and low weigth. Characteristic features: * Advanced manufacturing devices for the Gerotor gear set, which provide small volume, high efficiency and long life. * Shaft seal can bear high pressure of motor of which can be used in parallel or in series. * Advanced construction design, high power and low weight. Main specification type BMM8 BMM12 BMM20 BMM32 BMM40 BMM50 displacement 8.2 12.9 19.9 31.6 39.8 50.3 Max speed(rpm) rated 1537 1256 814 513 452 358 Cont. 1950 1550 1000 630 500 400 int. 2450 1940 1250 800 630 500 Max Torque (N*M) rated 8 13 19 31 37 33 Cont. 11 16 25 40 45 46 int. 15 23 35 57 70 88 peak 21 33 51 64 82 100 Max speed (kw) rated 1.3 1.7 1.7 1.7 1.7 1.2 Cont. 1.8 2.4 2.4 2.4 2.2 1.8 int. 2.6 3.2 3.2 3.2 3.2 3.2 Max pressure drop(MPa) rated 9 9 9 9 8.5 6 Cont. 10 10 10 10 9 7 int. 14 14 14 14 14 14 peak 20 20 20 16 16 16 Max flow(L/min) rated 14 18 18 18 20 20 Cont. 18 20 20 20 20 20 int. 20 25 25 25 25 25 Weight(kg) 1.9 2 2.1 2.2 2.3 2.4 Type Max.inlet pressure BMM8-50 Cont. 17.5 (Mpa) Int. 22.5 * Continuous pressure:Max. value of operating motor continuously. * Intermittent pressure :Max. value of operating motor in 6 seconds per minute. * Peak pressure:Max. value of operating motor in 0.6 second per minute. z
The AN61 series AC Power Supply adopts advanced SPWM technology, DSP digital processing technology and high-power switching power supply technology, in the field of AC power supply, it is leading in China and advanced internationally, and thus widely applied for the labs and production lines in power electronics, avionics, IEC standard test and other industries. AN61 series product possesses excellent power output quality: AC voltage output accuracy 0.4%; degree of distortion less than 0.3%; load effect less than 0.5%; can output AC, DC, AC+DC power and provide AC load, DC load and rectification load with precise power input. It has the ability of offering 6 times peak current and is optimal test instrument of measuring the surge current, and can be used to set the angle of waveform switch for testing the surge current and output holdup time. It can also be used to set the fluctuation ratio of voltage and frequency for scanning the range of power input to be tested. AN61 series product can simulate abnormal instantaneous rise, instantaneous drop, short circuit, jitter and others of electric supply, with the superposition function of harmonic waves or indirect harmonic waves, simulate the waveform distortion of electric supply, can also provide accurate and quick measurement of power parameters and harmonic waves, such as voltage root-mean-square value(Vrms), current root-mean-square value (Irms), true power, frequency (Hz), power factor (PF), current peak factor (CF) and 40-order current spectrum component. AN61 series AC Power Supply possesses strong programmable function, can complete the immunity test of IEC61000-4-1(test before certification) /-4-13/-4-14/-4-28 standard. Also, its programmable output impedance, together with the power analyzer, can complete the test of IEC61000-3-2/-3-3 harmonic wave current limit and flicker and is optimal choice of IEC standard test. Application: 1.Simulate power supply input interference Pulse, ladder, sequence and other output modes, simulating of any output wave in one step or continuously to simulate grid fluctuation 2.Testing of switching power supply inrush current Free setting of start/stop angles through the output wave, peak current output up to 6 times, the AN61 series power supply is an ideal device for testing the inrush current of the switching power supply. 3.Free wave amplification The AN61 series AC test power supply can amplify power of any wave through the specific external port. The customer can record the actual wave on site using the wave recorder, and then send it to the specific external port of AN61 power supply via the wave generator for power amplification, so that the customer can simulate the actual wave on site to test the product under test.
The long boom excavator arm,also known as excavator long reach booms, is made of structural grade tensile steel and heavy duty components,to handle a wide range of attachments for deep gravel pits, long excavations, dredging, marine construction, sedimentation embankments, waterway pond clearing, surface mining, slope stabilization, demolition of buildings and structures, and the largest range of other specialized projects. Quality control of long reach arm We supply long reach front packages for a wide range of excavator models, ranging from 10- 230 metric tons (22, 000 - 507, 000 lbs) operating weight. excavator booms and demolition excavator booms are custom designed to meet your machine and working distance requirements. Glikr Machinery is a professional excavator long reach boom manufacturer and supplier in China, specializing in the design and manufacture of long arm excavator boom components, high reach demolition boom, shortened rock booms and other types of excavator attachments. All long arm excavator booms are manufactured using factory certified steel, manufactured using cutting edge assembly methods and undergo rigorous quality checks at every stage of production to ensure that internal quality standards, OEM specifications and customer requirements are met. The long reach rooms kit includes The kit includes the boom and bucket bar, bucket linkage, bucket cylinders, POR and can be set up for different machines. We can also supply the boom and boom cylinders with associated pins, hoses and counterweights. Notes: Boom weight does not include lifting cylinders or buckets. Custom buckets and bucket sizes are available. All universal buckets are equipped with teeth. Features of long arm of excavators The excavator long reach boom is made of structural grade tensile steel and heavy duty components for more complex service conditions Plate edges are beveled prior to welding to ensure good weld depth. Critical areas are automatically welded and edge milled to prevent cracking and ensure a stronger structure. Internal baffles give the structure greater strength and durability to withstand torsional loads for use in high pressure areas High quality fittings such as piping, pins, bushings and cylinders, NOK seals Accepts custom long arm of excavator lengths to handle different applications Locking valve to prevent the arm from dropping when the hydraulic hose is blown Bucket cylinders with shields. Other accessories: standard excavator bucket, mud bucket, skeleton bucket, grab bucket.
Model PSX-300 Technical Parameter 1.Capacity18000BPH.(500ML). 2.Bottle MaterialPET,Glass,MetalPEHDPE. 3.Label Roll Inner Diameter6 inches (152 mm). 4.Bottle Diameter30-200 mm. 5.Bottle Height100-500 mm. 6.Label Height10-250 mm. 7.PowerAC 3Ï?, 380V/50HZ. 8.Air Consumption3-6 kg/cm² 9.Power Consumption16 KW. 10.Main machine size: 2200L*2300W*2000H(mm). Features: 1.Auto cutting and Sticking circle or half circle of bottle. Auto melting and attaching glue on top and rear of the label , glue auto recycling . 2.Variable speed control system, synchronous automatic detection system, automatic adjust production speed, Always make the labeling machine at best production speed 3.Star Wheel separation and feeding ,correlation design transmission mode high-speed labeling, stable precision. 4.Servo motor synchronous tracking, with special designed vacuum drum adsorption, labeling precise and stable 5.Abnormal situation, this machine has safety device, automatic stop immediately. 6.Following conditions the machine will automatically stop and alarm: (1) Label is not labeled on bottles (2)Label sticker failure (3)Label is about to run out (4)Abnormal bottle feeding (5)Abnormal bottle out (6)Abnormal bottle jam 7.The whole machine centralized lubrication system, easy to clean, lubrication and maintenance. 8.Techmach electronic automatic rectify guide system, digital electronic eye for ultrasound method.Non-contact electric eye, automatically adjust the label location. (optional). 9. Label top and end difference within 2mm ( without Techmach), 1mm with techmach Shanghai Xinhua was founded in 2006 in Shanghai China and celebrated its 10th anniversary in 1016 as a Chinese leading manufacturer of shrink sleeve applicators,and heat shrink tunnels for the worldwide packaging industry.Especiaaly in te auto shrink sleeve labeling plastic cup,tapes.we have accumulated more than ten years experience,we have a complete set of auto packaging production line for cup and tape sleeving,moreover we are the market leader,our equipment is widely praised at home and abroad. SHANGHAI XINHUA CHINA Auto shrink label Sleeve applicator Machine is for applying heat shrinkable sleeve label or neckbands which is commonly used on various packages ranging from boottles,cups,tapes,jars and other containers.Shrink sleeves can wrap and conform to a container's every curve, enabling complete decoration of unusual shapes from top to bottom with 360 degrees.Shrink sleeves are widely used to decorate everything from foods,beverages,cosmetic,medical and even personal products like Shamppo lip sticks eye drop,etc.
Insulation thermal mortar production line,glazed hollow beads mixer machine,vitrified hollow bead of thermal insulation mortar equipment Glazed beads of thermal insulation materials production line mainly by the hybrid systems, storage systems, copolymer material hybrid systems, conveyor systems, metering systems, packaging systems, dust removal system and other accessories. Master batch mixing system: based on gravity mixer, for mixing of the masterbatch; Storage System: used to store vitrified (hollow) beads, finished masterbatch; Copolymer material mixed system: the glass of the (hollow) beads dedicated centrifugal mixer for the main set of streaming, Tuochen technology in one; Delivery system: Masterbatch products rely on bucket elevator conveyor to the high feed tank storage, glass (hollow) beads rely on vacuum conveying system to transport material mixed copolymer system, at least to reduce the crushing of raw materials; Measurement system: automatic measurement of formulation; Packaging system: specific gravity drop, frangible pellet packaging machine; Dust removal system: pulse jet bag filter. Features: 1. Effective security control system, professional electrical design, quality assurance; 2. Wear-resisting durable powder conveying system and accurate weighing system; 3. Sewing platform design and packing machine and pneumatic packing machine are suitable for packaging of insulation mortar; 4. Unique sealing of feed discharging mouth, prevent leakage powder; 5. Customized dust collector system, green and environmental protection, create a good working environment for you; 6. Short installation period, low installation cost. 7.one component of inorganic insulation mortar production line, thermal insulation mortar production line ribbon outer ring and the inner wall of the casing clearance are adjustable, and a cleaning door, no residue production. Accelerate mixing speed. One component of inorganic thermal insulation mortar production line, the production line structure: Double seal spiral circulation, stirring time 5--8 minutes, even degree over 95%, discharging time 5--10 minutes. Weight: 800--900 KG. Material: steel plate thickness: 3--4 mm. Spindle speed: 1400 r/pm. Specifications: Drum mixer 3m³ Multi-ribbon pre-mixer HK500 Material adding hopper 0.5m³ stirring time 5--8 minutes discharging time 5--10 minutes Weight 800--900KG steel plate thickness 3--4mm Spindle speed 1400 r/pm Item Number AH-G
