Poduct Name L-Glutathione Reduced Other Name Glycine, L-�³-glutamyl-L-cysteinyl Cas No. 70-18-8 MF C10H17N3O6S Appearance Powder Color White Purity 99% Min Package 1kg/aluminum foil bag; 25kg/drum Introduction of L-Glutathione Reduced: Glutathione (GSH) is named Reduced glutathione or L-Glutathione Reduced ,an important antioxidant in plants, animals, fungi, and some bacteria and archaea,a white crystalline powder. It is atripeptide with a gamma peptide linkage between the carboxyl group of the glutamate side chain and the amine group of cysteine, and the carboxyl group of cysteine is attached by normal peptide linkage to a glycine.Thiol groups are reducing agents, existing at a concentration around 5 mM in animal cells. Glutathione reduces disulfide bonds formed within cytoplasmicproteins to cysteines by serving as an electron donor. In the process, glutathione is converted to its oxidized form, glutathione disulfide (GSSG), also called L-glutathione. Application of L-Glutathione Reduced : 1.L-Glutathione Reduced has elimination function of lipid peroxide and grease resistance to oxidation. And has anti-lipid oxidation. It can also prevent flavor nucleotides (inosinic acid, guanylic acid) food (fish cake, sausages, sauces, etc) lose their fresh flavor nucleotides in decomposing. Besides, it can strengthen the food flavor, and greatly extend the shelf life of food. 2.Add L-Glutathione Reduced into the canned fruit, it can prevent fruit browning; Add to dairy product, it can effectively preventenzymatic and non enzymatic browning. 3.L-Glutathione Reduced can be used as a flavoring agent in various processed foods. It also has the effect of enhancing flavor when added to meat and cheese. 4.L-Glutathione Reduced has the function of protecting the liver, inhibiting formation of fatty liver. Liver protection agent.Owing to its broad spectrum of physiological function, it can be widely used in the food,especially in anti-aging, enhance immune function and anti-tumor functional food base, enhance nutrition, additives and so on.
Magnesium ingot Features: 1.Corrosion resistance and light weight. 2.The density of magnesium is 1.74g/cm3 which is even lighter than aluminum 2.7g/cm3, but mechanical strength and chemical stability are much better than aluminum. 3.Magnesium can be directly related to nitrogen, sulfur and halogen such as chemical combination, including hydrocarbons, aldehydes, alcohols, phenols, amines, grease and most of the oil pharmaceutical . Chemical composition : Mg Ingot Brand Chemical composition Mg Fe Si Ni Cu Al Cl Mn others Mg99.98 99.98 0.002 0.003 0.002 0.0005 0.004 -- 0.002 0.02 Mg99.96 99.96 0.004 0.004 0.0002 0.002 0.006 0.003 0.003 0.04 Mg99.95 99.95 0.004 0.005 0.0007 0.003 0.006 0.003 0.01 0.05 Mg99.9 99.9 0.04 0.01 0.001 0.004 0.02 0.005 0.03 0.1 Mg99.8 99.8 0.05 0.03 0.002 0.02 0.05 0.005 0.06 0.2 Application : 1.Magnesium alloys can be used to manufacture aircraft fuselages,engine parts, etc. 2.As strong reducing agent for titanium, zirconium, beryllium, uranium and hafnium production. 3. Magnesium metal is the main alloying element in aluminum alloy 4.Magnesium powder can be used as desulfurizer for steel making. 5. Magnesium also used to make photography and optical instruments, etc. 6.Can be used to produce magnesium fertilizer, promote the absorption and utilization of phosphorus by plants. 7.As an additive agent in conventional propellants and the production of nodular graphite in cast iron.
Product Description Appearance and features white tetragonal crystal molecular weight 23.95 pH(1mol/L) 14 Solubility Soluble in water, slightly soluble in ethanol melting point 471.2�ºC molecular formula LiOHChemical properties It is easy to absorb carbon dioxide and moisture in the air, but the absorption capacity is slightly worse than that of NaOH and KOH. Lithium hydroxide has the general property of alkali, and the following reactions can occur. 1. alkaline reaction It can make purple litmus test solution blue and colorless phenolphthalein to turn red; and its concentrated solution can denature phenolphthalein after experimental verification, so that the solution changes from red to colorless (similar to concentrated NaOH). 2. neutralized with acid HCl+LiOH=LiCl+H2O 3. Reacts with acidic oxides 2LiOH+CO2=Li2CO3+H2O (this reaction is used to absorb carbon dioxide in aerospace) 4. Reacts with metal salt solutions FeCl3+3LiOH=Fe(OH)3â??+3LiCl Usage Lithium hydroxide can be used as developing agent and lubricating oil for spectral analysis. The additive of alkaline battery electrolyte can increase the electric capacity by 12% to 15% and increase the service life by 2 to 3 times. It can be used as an absorbent for carbon dioxide and can purify the air in submarines. The chemical equation is: 2LiOH(s)+CO2(g)=Li2CO3(s)+H2O(l). It is used to make lithium salt and lithium-based grease, electrolyte of alkaline battery, absorption liquid of lithium bromide refrigerator, etc.; used in petroleum, chemical industry, light industry, nuclear industry, etc. When used in alkaline batteries, the aluminum content is not more than 0.06%, and the lead content is not more than 0.01%. It is used as an analytical reagent, a photographic developer, and also in the manufacture of lithium; it is used as a raw material for the preparation of lithium compounds. It can also be used in metallurgy, petroleum, glass, ceramics and other industries.
Lithium metaborate (LiBO2) is a chemical compound. The chemical formula LiBO2. Molecular weight 49.75. A colorless trisoclinal crystal with a pearly luster. Melting point 845 C, relative density 1.39741.7. Dissolve in water. Decomposition begins above 1200 C. Lithium oxide is formed. The octahydrate is a colorless tripartite crystal with a melting point of 47 C and a relative density of 1.3814.9. Preparation method: It can be made from stoichiometric lithium carbonate and boric acid melting. Purpose: To make ceramic materials. Product Name Best Price LITHIUM METABORATE / Boricacidlithiumsalt / CAS 13453-69-5 CAS NO. 13453-69-5 Appearance White Powder Purity 99% Melting Point 845 C Density 1,4 g/cm3 Storage Store at +5C to +30C Application Intermediates; Biochemical reagent; Chemical raw materials Usage LITHIUM METABORATE is used in pharmaceutical industry and preparation of acid resistant enamels. Appearance and properties: white crystal or powder Density: 1,4 g/cm3 Melting point: 845 C(lit.) Stability: Stable. Application It is used in the pharmaceutical industry and in the preparation of acid-resistant enamels 1). For the pharmaceutical industry and the preparation of acid-resistant enamel 2). 99% is used as a flux in the glass or ceramics production industry. 99.9% is used as an additive for the production of lithium-based greases. LiBO2 % 99.9 min Al % 0.005 max Ca % 0.01 max Fe % 0.005 max Na % 0.01max P % 0.005max Si % 0.01 max LOI(500C/1h) % 2.0 max Bulk Density g/cm3 0.3-0.6
Cross Shaft Universal joints create a reliable mechanical connection between several rotating axes. It is worth mentioning here that these axes do not remain parallel. On the contrary, they cross each other. The purpose of these shafts is to transmit motion or power. Sometimes, they provide both, for example in vehicles or industrial machinery. Of all the different types of joints available, the universal joint is one of the most common. There are two yokes, one on each shaft. They are kept connected by a cross-shaped intermediate member called a star wheel. Function The power transmission shaft utilizes minimal space requirements, connecting the drive shaft to the driven shaft at an angle through the smoothing mechanism of the universal joint. Usually a set of 2 universal joints are installed in one shaft. During assembly, it is positioned at â? the same working angle â?¡ the same plane and â?¢ the same phase to achieve uniform speed. Structure The universal joint consists of a star (cross) bearing and 4 grease-filled roller bearings. It can transmit high torque with low friction. Spiders with journal pins and bearing housings as outer rings are hot forged or cold formed and machined. They are subsequently carburized in a furnace for greater firmness and wear resistance. Parts are eventually ground to design dimensions to tight tolerances. Oil seals and dust caps are also used to protect the internal journal area from foreign objects. Choose from a variety of grades and materials to handle extreme conditions such as very hot/very cold temperatures. Applications of Cross Shaft: Some typical applications for universal joints include electrical appliances, aircraft, instrumentation, control mechanisms, electronics, ordnance, medical and optical equipment, textile machinery, sewing machines, radio and tool drives. Different manufacturers use different materials to produce them. That is why you will find universal joints made of steel and thermoplastic. Steel products have a specific load shaft capacity, depending on their dimensions. On the other hand, thermoplastic varieties are suitable for light industrial applications. They are self-lubricating in addition to being lightweight, corrosion-resistant, have negligible clearance, and the ability to accommodate high speeds. If you are interested in our products, please contact us.
WJWAX specializes in producing food grade paraffin wax and microcrystalline wax in both granular and slab forms. We can provide Kosher, HALAL, ISO, FDA certifications, direct sales from manufacturers, good prices, and excellent quality. Granular food wax, also known as food-grade wax, is a specialized wax product used in the corrugated board industry for various applications. It is specifically designed to provide a protective coating to corrugated boards used in food packaging. One of the primary functions of wax is to enhance the moisture resistance of the corrugated board. It forms a waterproof barrier that prevents moisture from penetrating the board, thereby preserving the integrity and strength of the packaging. This is particularly important for food products that are prone to moisture damage, such as fresh produce or frozen goods. In addition to moisture resistance, food grade wax also helps to improve the grease resistance of the corrugated board. It acts as a barrier against oils and fats, preventing them from seeping into the packaging and compromising its structural integrity. This is crucial for packaging food items that contain oils, such as fried foods or greasy snacks. Furthermore, food wax provides a smooth and glossy surface to the corrugated board, enhancing its visual appeal. The wax coating gives the packaging a professional and attractive finish, making it more appealing to consumers. The application of wax on corrugated boards is typically done through a wax curtain coater or a similar coating process. The boards are passed through the wax curtain, and the granular wax adheres to their surface, forming a uniform and consistent coating.
Ball screw gate valves are designed for large caliber, high-pressure manual valves. The valve combines the tail balance lever and the unique ball principle to make its operation light, low torque, and easy to operate. Its diameters range from 3 1/16 "to 9" and its pressures range from 10,000 psi to 20,000 psi. Product features: 1. Two-way downstream sealing structure, which improves the service life; 2. Fixed metal seal (between gate and seat and seat and body); 3. Simple and reliable gate and seat design can reduce field service; 4. Sealing ring between seat and body helps seal at low pressure. They also prevent granular contaminants from entering the body chamber and sealing area; 5. Stem seal design covers all pressure classes, temperature ranges, and all fluid conditions encountered in wellhead and manifold environments; 6. Metal seal between bonnet and valve body, up to 20000psi working pressure; 7. Reverse stem seal structure allows the valve to replace stem seal under pressure drive; 8. To ensure safety, a grease injection device can be placed on the stem after the inverted seal. The device can be placed on the bonnet to eliminate body leakage; 9.Ball screws can effectively improve the switching efficiency and reduce the switching torque, which is more conducive to opening and closing the valve easily and quickly. For more information, please visit our website.
SAFFRO'S aura Premium Gloss Enamel gives smooth,hard & glossy finish.Its dry film has good adhesion to the surface.It has very good flow and brushability. aura Premium Gloss Enamel is a highly washable paint, thus you can wipe off most common household stains easily RECOMMENDED USE It is applied on furnitures,drums,barrels,household products,elecrical motors,doors,windows and variety of other surfaces which are not subjected to outdoor exposure FINISH :smooth and glossy COLOR As per shade card Including White and Black. COVERING CAPACITY :7 to 9 sq.mt/lit/coat at 30 to 35 micron dry film thickness,depending (ON SMOOTH MILD STEEL SURFACE) upon shades and surface. DRYING TIME :Surface dry - Less than 3 hours. :Hard dry - Less than 15 hours. Second coat application period -After 10 hours Above all properties depend upon temperature and humidity. FLASH POINT :Above 30* C (86 *F) THINNER RECOMMENDED :SAFFRO Synthetic G.P Thinner METHOD OF APPLICATION :By Brush or spray at a pressure of 40 to 50 P.S.I RECOMMENDED PRIMER :For Metal - SAFFRO R/O Z/C metal primer - SAFFRO Zinc Chrome primer yellow For Wood - SAFFRO Wood primer white For Plaster - SAFFRO Cement primer (oil base) DIRECTION FOR USE Remove dust,grease,oil,moisture,rust and other loose flakes etc.After priming the surface with recommenden primer with over night drying & sanding with emery paper,apply SAFFRO SHINE synthetic enamel using recommended thinner.Allow first coat to dry for minimum 10 hours before applying second coat.Stir the content thoroughly prior to use PACKING : 20 Ltr, 10 Ltr,4 Ltr ,1 Ltr, 500 ml,200 ml,100 ml,50 ml.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Type 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data :- COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Type 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Product Data Sheet GENERAL DESCRIPTION An easy-to-use, water-based primer specifically formulated to �¢??lock-out�¢?? corrosion on a wide range of metals. Applied correctly, is guaranteed for years. USES Suitable on sheet metal, castings, wrought iron, TNT Bar, steel Bar and steelwork. This product is not recommended for automotive use. COLOURS Available in natural green. SIZES Available in 4 litre,10 litre and 20 litre COVERAGE Up to 14 square metres per litre depending upon surface porosity and application method. APPLICATION Roller, brush, dip or airless spray. Provide adequate ventilation during use. DRYING TIMES Touch Dry Time - 20 minutes. Recoat Dry Time - 2 hours. Drying times refer to normal conditions (30�?�°C, 50% humidity). Under cooler, humid or still conditions, longer drying times may be necessary. DO NOT USE IN TEMPERATURES BELOW 10'c OR ABOVE 45C. DANGEROUS GOODS CLASSIFICATION Not classified as Dangerous Goods. SURFACE PREPERATION Previously Painted Surfaces : Scrape off loose and flaking paint and make sure the remainder is firmly attached. Sand glossy surfaces and enamels thoroughly and wipe clean. Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust. Prime treated and bare areas with one coat SAFFRO Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of SAFFRO Anti- Corrosive Metal Primer. TNT BAR,STEEL BAR AND IRON: Remove all grease, dirt and other surface contaminants.Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust with. Prime treated and bare areas with one coat SAFFRO Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of SAFFRO Anti- Corrosive Metal Primer
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data COLOUR : Grey FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Thinner 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Description Two-component, air drying polyurethane based clear. Recommended Use :- This product is recommended Top coat for glossy , uv protection,weather property and also as penetrating primer on bare concrete, wooden substrate prior to application of subsequent coating system. Physical Data :- COLOUR : Clear FINISH : Smooth & Glossy SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 16 sq.mt / ltr at a DFT of 25 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation New concrete should be cured for at least 1 month prior to paint application. Ensure concrete surface is absolutely dry and free from moisture, oil, laitance, dust and dirt. For old concrete, ensure surface is free from oil, grease, algal & fungal growth and any old coating. Sand Blasting on concrete gives the best performance and should be given first preference out of the available surface preparation methods. If blasting is impracticable, Acid Etching with diluted Hydrochloric Acid followed by fresh water washing to be adopted. Seasoned wooden articles should be scuffed with Emery 220/400 to achieve smooth surface. Please refer our Directive Sheet on Surface Preparation. Application Data MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Type 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : Indefinite COMPATIBILITY : Can be applied on Epoxy primers and oleo-resinous primer and coated / over coated by two component paints like Epoxy, PU, etc.
Description SAFFRO MELLOW COATINGS & RESINS MELLOWTEX RUSTIC/DHOLPURI/BUBBELS is a textured finish composed of high quality durable acrylic modified resin specially designed as an intermediate coating. RUSTIC imparts a super premium look to the walls. BENIFITS :- Hides Fine Cracks It hides surface undulations and fine cracks. Tough Textured The tough texture finish lasts for long and ensures low maintenance. Plaster Protection It increases the life of plaster by protecting it from wind driven rain. UV Resistance It has excellent UV resistance and adhesion. Anti-algal Formula It resists fungal and algal growth when applied as system, with the recommended top coat. Technical Information :- Drying time: Surface dry time 30 - 60 min. Flash point IS101/1987 Part 1, Sec 6: NA. Coverage :- Pre-painting Steps Plaster New masonary surfaces must be allowed to cure completely. It is recommended to allow 28 days as the curing time for new masonary surfaces. Cleaning Surface should be free from any loose paint, dust or grease. Growths of fungus, algae or moss should be removed by wire brushing and water. When the underlying surface exhibits chalkiness, in spite of thorough surface cleaning, use Saffroâ??s Exterior Primer. How To Apply :- On normal masonary surface by a trowel spatula to obtain an even coating of 1 to 1.5 mm ,2 coats 2 to 2.5 sq.ft/kg** (**Actual coverage may very from the quoted coverage due to factors such as method and condition of application and surface roughness and porosity.) Filling For Holes & Dents :- In case of dents and holes use Saffro Mellow Coatings & Resins SUMO Acrylic Wall Putty or white cement and fine sand in the ratio 1:3. Saffro Mellow Coatings & Resins,MELLOW TEX RUSTIC should not be applied on surfaces / substrates that are subjected to continuous seepage or dampness.
Two component air drying Epoxy based clear primer with Polyamide as curing agent. Recommended Use :- This product is recommended as penetrating primer on bare concrete, wooden substrate prior to application of subsequent coating system. Physical Data :- COLOUR : Clear FINISH : Smooth & Glossy SOLIDS BY VOLUME : 50 �± 3% THEORETICAL SPREADING RATE : 20 sq.mt. / ltr. at a recommended DFT of 25 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Thorough surface preparation is vital. For best results, saffro recommends mechanical preparation techniques (Eg. mechanical scarifying, grit or sand sweeping), a) New Concrete Surface :- New concrete surface should be at least 28 days old and/or have moisture content of less than 5% before proceeding with primer application. Laitance and deposits on new concrete are best removed by light grit blasting, mechanical scarification or grinding. Acid etching may be considered for smaller areas, after etching the floor, it should be thoroughly washed with clean water, and then allowed to dry. b) Old Concrete Floors :- Mechanical cleaning methods are strongly recommended on old concrete surfaces, particularly their heavy contamination by oil and grease has occurred or old coatings is present. To ensure good adhesion, all contaminants are removed and the surface thoroughly cleaned of all dust and loose debris. A thorough detergent wash is also recommended followed by thorough cleaning with water and moping it off to a dry state.
EXXED POWDER, which is a highly effective cleaning powder designed to effortlessly remove dirt and stains from a variety of surfaces. Whether it's porcelain, ceramic, enamel, glass, fiber materials, metal, or kitchen utensils, EXXED POWDER delivers remarkable cleaning power. Key Advantages of EXXED POWDER: Powerful Cleaning: Our product excels at swiftly and effectively eliminating dirt, stains, including water stains, metal oxidation, and even tough grease, oil, and workshop stains. Surface Protection: EXXED POWDER leaves surfaces clean, pristine, and scratch-free, ensuring no damage or surface burns. Invigorating Fragrance: Featuring a refreshing lemon fragrance, our cleaning powder enhances the overall cleaning experience, leaving behind a pleasant aroma. Environmentally Friendly: We prioritize sustainability, and therefore, EXXED POWDER is biodegradable and naturally decomposes, minimizing its impact on the environment. Ease of Use: With its quick water-soluble formula, our product dissolves effortlessly, making it simple to prepare and apply. Skin-Safe: EXXED POWDER is designed with your well-being in mind. It is gentle and safe on the skin, ensuring a worry-free cleaning experience. Cost-Effective: We understand the importance of value for money, and our product offers exceptional effectiveness while being economical, providing long-lasting value. Versatility: EXXED POWDER is a versatile cleaner suitable for a wide range of cleaning tasks. Its multi-functional nature allows for efficient cleaning across various surfaces and materials.
4x3C-TH Slurry Pump is engineered with the latest hydraulic and wear technologies to cope with the most severe corrosive and abrasive slurry applications, The 4x3C-AH pumps feature patented innovative designs that can significantly reduce the operational costs of slurry pumping, It is widely used in industry of mining, electrical power, metallurgy, coal, environmental protection, etc for transportation of abrasive solid slurry. Design Features: â?? The 4x3 C TH slurry pump frame plates have replaceable wear-resistant metal liners, impellers & volute liners are made of wear-resistant metal(such as A05, A49,and other high chrome metal). â?? The 4x3 C TH slurry pump bearing assembly use cylindrical structure, adjusting the space between impeller& front liner easily, being removed completely when being repaired. Grease lubrication. â?? The 4x3 C TH slurry pump shaft seal could use the packing seal, expeller seal and mechanical seal. One pump also can be use packing seal with expeller seal together. â?? The discharge outlet can be positioned at intervals of 45 degrees by request and oriented to any 8 positions to suit installations and applications. â?? The 4x3 C TH slurry pump can be installed in multistage series to meet the delivery for long distance. â?? The 4x3 C TH slurry pump drive types, such as direct coupling drive (DC), V belt drive (CR, CV, ZV) etc.
Item no size WLL/T Technical parameter/mm Weight/kg B K L A G D H T J W I DS089Y-007 0.75 0.75 34 107 133 15 6 10 22 12 10.5 35 13 0.5 DS089Y-015 1.5 1.5 40 119 159 18 8 13 26 15 13.5 46 20 0.9 DS089Y-030 3 3 53 160 210 23 10 19 32 20 20 57 25 2.2 DS089Y-050 5 5 67 203 267 32 14 22 37 26 33 69 32 4.4 DS089Y-085 8.5 8.5 78 250 326 40 14 30 54 32 37 92 38 7.4 DS089Y-100 10 10 106 310 410 42 25 38 54 42 44 104 50 18.0 DS089Y-150 15 15 119 320 440 48 25 38 57 49 54 117 60 21.2 DS089Y-250 25 25 137 405 540 62 30 50 70 60 66 140 70 40.0 DS089Y-350 35 35 154 415 550 62 30 50 70 60 66 140 70 46.7 DS089Y-600 60 60 270 670 890 100 75 80 120 75 80 230 110 302 Forged super alloy steel-Quenched Tempered. Swivels are design with a safety factory of 4:1 Swivel are individually tested to 2 times the sea working load with certification. Swivel are zine plated for corrosion resistance and longer life. Swivels are manufactured with grease fitting for superior performance.
Polyglycerol polyricinoleatePGPR Characters: Yellow viscous liquid, insoluble in cold water and ethanol, soluble in hot grease, non-ionic water-oil emulsifier (W / O). Applications: No bad odor, has good thermal stability. Used in chocolate, add a small amount, can significantly improve the mobility of chocolate products, and save the amount of cocoa butter. Expedit the process of filling and mold forming for chocolate products, optimize the process and make the small bubbles to discharge easily, and then avoid occuring empty holes and pore in the chocolate products. Used with lecithin , has a good synergistic effect, thinning the thickness of chocolate coating to make it easy to process. In humid conditions, can reduce the viscosity. And form chocolate sugar coat quickly. And accelerate its conglutination . And increase adhesion, reducing the small pores. Opeartion method and dosage The suggestion of maximum in cocoa products, chocolate and its products, candy, chocolate coated products, ice cream coating: 5.0g/kg, oily-water fat emulsified products: 10g/Kg. Technical Index Poly glycerol(Dimer, trimer and tetramer glycerol)()75 Poly glycerol(More than Heptamer)( )10 Pb / (mg/kg) 2 Packaging Plastic bucket or Iron bucket inner coating plastics, net weight is 25 kg, 180 kg. Storage and transportation: Sealed and stored in the cool, dry and well-ventilated place, avoid to put inversion, Forbid to store and transport with materials that is explosive, combustible or deleterious. The shelf life is 12 months.
SLX 5376 cam type jacquard machine are in strict material selection and production process perfect balance of moving parts, conjugate cam oil bath lubrication, all bearings permanent lubrication to ensure wear resistance, long service time, maintenance work will be reduced to the minimum, coaxial system driven by conjugate cam. Further strengthened drives and sturdy base of this electronic jacquard weaving looms make the machine to withstand higher loads. This computerized jacquard machine is suitable for various of weaving looms, such as rapier loom, air jet loom, water jet loom, shuttle loom, projectile loom. It is applicable to rapier loom, air jet loom, water jet loom, shuttle loom, projectile loom with any reed width. This model of cam type electronic jacquard machine is used to weave label, tie, upholstery fabric, curtain fabric, shading fabric, sofa cloth, bedding cloth, towel, carpet, velvet, garment fabric, sari fabric, silk fabric, lining fabric etc. Hooks 5376/ Shed Opening 55-120mm/Max Speed 750 rpm/ Advantageous Features 1. Sealed fuselage, optimized filtration and ventilation system of our cam type digital jacquard machines can effectively prevent flying flowers into the system. 2. The optimized shuttle opening keeps good effect. The opening curve can be designed according to the need to ensure the best weft insertion, reduce the tension on warp yarn and breaks. 3. The self-locking characteristic of the conjugate CAM can reduce the interference to the braking performance of the loom. 4. The concentrated lubrication oil hole and grease hole are easy to reach and check. 5. The small pull rod composite bearing with special filling hole, to ensure the longer service time.
