WALL GUARD PUTTY is a white cement based product with redispersible polymer and functional additives for application on interior and exterior rough plasters to give a smooth finish. FEATURES :- WALL GUARD PUTTY 1. Provides smooth and uniform finish to rough plasters 2. Good Workability 3. Does not require curing with water 4. Good water resistance 5. Good Tensile Adhesion Strength, Compressive Strength and Flexural Strength 6. Controlled water vapour permeability 7. Excellent abrasion resistance 8. Resists growth of algae and fungi on wall 9. Good intercoat adhesion to emulsion paints RECOMMENDED APPLICATION :- It can be used on all types of exterior cement plasters/interior walls, asbestos sheets, concrete etc PRODUCT TECHNICAL DATA :- COLOURS : White FINISH : Smooth and Matt COVERAGE : 2 coats: 10-15sq.ft/KG up to 1.5 mm thickness in two coat (It may vary from the quoted coverage to factor such as method and condition of application and surface roughness) DRYING TIME : 6-8 HOURS GLOSS LEVELS/SHEEN LEVELS : Silky smooth sheen FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable SUITABILITY OF THINNER PAINT Use within 24 hrs. SHELF LIFE 3 years from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat. PERFORMANCE DATA :- ABRASION RESISTANCE : Excellent WATER RESISTANCE : Excellent SHELF LIFE : 3 years from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat. REMARKS : a) Kindly refer to the MSDS for the Saffro Mellow Coatings And Resinswhich gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts, wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling the paint. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The low solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance. Recommended Use :- It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected industrial shades FINISH : Semi glossy SOLIDS BY VOLUME : 80 + 2% THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80 FLASH POINT : Base : Above 25C Hardener : Above 25C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO : Base : Hardener ( As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 RECOMMENDED DFT : 75-100 mic. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats.
No. Type Pure Acrylic Emulsion with high sheen. 1 FEATURES It provides a smooth long lasting rich finish with high sheen to the interior and exterior wall. It is washable and most stain can be removed easily by sponging with mild soap solution. The paint film is having good resistance to fungus and mildew. 2 RECOMMENDED APPLICATION STAR valvet glow emulsion is an interior and exterior wall finish that can be applied on all type of smooth plaster, false ceiling, asbestos sheets, concrete etc. PRODUCT TECHNICAL DATA No COLOURS White & other shades as per shade cards 1. FINISH Smooth and high sheen 2. COVERAGE On smooth primer masonry surface by brushing 1 coat: 140-160 sq.ft/ltr 2 coats: 80-90 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc.) 3. DRYING TIME Surface drying time â?? 10-15 minutes 4. GLOSS LEVELS/SHEEN LEVELS Silky smooth with high sheen 5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable 6. SUITABILITY OF THINNER PAINT Use within 24 hrs. 7. SHELF LIFE 3 years from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat. PERFORMANCE DATA No ABRASION RESISTANCE Excellent 1. WATER RESISTANCE Excellent 2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins STAR velvet glow emulsion which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
WALL BIND ACRYLIC Cement Primer Water Thinnable No. Type WALL BIND Acrylic Interior Wall Primer (Water Thinnable) is suitable for useas a primer for painting of waterbased wall finishes such as distemper and plastic emulsions. 1 FEATURES WALL BIND has a special features are better whitness and opacity, easy brushing, excellent covering,alkali resistance,quick drying and good filling properties. Provides superior hiding and superior whiteness. 2 RECOMMENDED APPLICATION WALL BIND can be used for priming plastered wall,asbestose,brick work,cement concrete etc. PRODUCT TECHNICAL DATA No COLOURS White 1. FINISH Smooth and matt 2. COVERAGE 1 coat: 130-140 sq.ft/ltr 2 coats: 80-90 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc.) 3. DRYING TIME Surface drying time â?? 10-15 minutes 4. GLOSS LEVELS/SHEEN LEVELS NA 5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable 6. SUITABILITY OF THINNER PAINT Use within 24 hrs. 7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat. PERFORMANCE DATA 2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins Nano Acrylic Cement Primer which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description Two component Epoxy based anti corrosive primer pigmented with Zinc Chromate as corrosion inhibiting pigments. Recommended Use :- It is recommended as primer on M.S surface for original equipment manufacturing as well as for process industry as in various fertilizer, refineries, petrochemical, chemical and other plants, applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. Physical Data COLOUR : Assorted FINISH : Matt SOLIDS BY VOLUME : 40 ± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS : SURFACE DRY : 60 90 minutes (At 65% Relative Humidity & at 30�°C) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Epoxy thinner 190 POT LIFE : 4 hours min at 30 C RECOMMENDED DFT : 30 - 40 au. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application :- By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 psi For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Addition : Max 5% if required Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 psi
Description Two component Epoxy based anti corrosive primer containing red oxide and zinc chromate as corrosion inhibiting pigments Recommended Use :- Recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate service conditions. Not to be recommended for immersed water condition Physical Data COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 + 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lt at recommended DFT of 30 FLASH POINT : Base : Above 23C Hardener : Above 23C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : SURFACE DRY : 60 - 90 minutes HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 POT LIFE at 30�°C : 4 hours min at 30�°C RECOMMENDED DFT : 30 40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated Rubber and Synthetic Enamel finish paints. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 p.s.i. For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : Max 5% if required Nozzle Orifice: 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
No. Type Nano acrylic Interior Wall Primer (Water Thinnable) is an economy water-based primer that enhances the application and finish of interior topcoats. 1 FEATURES Nano Acrylic Cement Primer is water based, Economical interior primer with good whiteness,good coverage and flow and leveling properties. 2 RECOMMENDED APPLICATION Nano Acrylic interior wall primer that can be suitable for priming plastered wall,asbestose,cement concrete etc. PRODUCT TECHNICAL DATA No COLOURS White 1. FINISH Smooth and matt 2. COVERAGE 1 coat: 90-100 sq.ft/ltr 2 coats: 60-70 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc.) 3. DRYING TIME Surface drying time â?? 10-15 minutes 4. GLOSS LEVELS/SHEEN LEVELS NA 5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable 6. SUITABILITY OF THINNER PAINT Use within 24 hrs. 7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat. PERFORMANCE DATA 2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins Nano Acrylic Cement Primer which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description Two components, air drying, high build Epoxy primer. The product has the advantage of epoxy resin composition with specialty pigments, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to be completely wet and provide maximum intimacy with the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. With the high solids and less solvent content of the coating the risk of lifting, blistering, pin holing is reduced, and thus the risk of adhesion failure is minimized. Recommended Use :- It is recommended for steel structures in industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected Industrial shades FINISH : Matt SOLIDS BY VOLUME : 63 + 3% THEORETICAL SPREADING RATE : 8.4 sq.mt / lt at a recommended DFT of 75 FLASH POINT : Base : Above 25C Hardener : Above 25C DRYING CHARACTERISTICS (At 30C & 65% Relative Humidity) : HARD DRY : 16 - 18 hours FULL CURE : 7 days SHELF LIFE : Base: 6 months Hardener: 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible than manual cleaning by mechanical methods like wire brush, emery paper, hand / power tools, etc. to achieve St-2 / St-3 cleaning standards of Swedish specification. The surface should be free from moisture, oil, dust and dirt and should be absolutely dry before painting. Removal of loose rust is a must. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation ) POT LIFE : 2 hours at 30�°C APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 RECOMMENDED DFT : 75-100 �µ. OVERCOATING INTERVAL : MIN : 8 hrs. MAX : 24 hours (In case it is exceeded, the surface should be roughened byemery scuffing) OVERCOATABILITY : Epoxy, PU, Chlorinated Rubber and Synthetic Enamel intermediate &finish coat.
ULTRA PREMIUM weatherproof interior and exterior emulsion is a smooth, water-based, modified acrylic, interior and exterior wall finish with silicon additives. FEATURES :- ULTRA PREMIUM weatherproof interior and exterior emulsion is specially formulated to withstand extreme tropical conditions of rainfall, humidity and heat ULTRA PREMIUM provides excellent resistance from growth of algae and fungi on the walls. This prevents appearance of black spots due to algal growth. ULTRA PREMIUM provides extremely good protection against alkali and UV degradation, thus ensuring that the shade doesnâ??t fade for a long time and the paint lasts longer. RECOMMENDED USE :- ULTRA PREMIUM Acrylic interior and exterior emulsion is interior and exterior wall finish that can be applied on all type of smooth plaster, asbestos sheets, concrete etc. PRODUCT TECHNICAL DATA :- COLOURS : White & other shades FINISH : Smooth and soft sheen COVERAGE : On smooth primer masonry surface by brushing 1 coat: 140-170 sq. ft/ltr 2 coats: 85-95 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc) DRYING TIME : Surface drying time â?? 30 minutes GLOSS LEVELS/SHEEN LEVELS : Silky smooth with soft sheen FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable SUITABILITY OF THINNER PAINT Use within 24 hrs. SHELF LIFE 18 month from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat. PERFORMANCE DATA :- ABRASION RESISTANCE : Excellent WATER RESISTANCE : Excellent REMARKS : 1) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. 2) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. 3) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. 4) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling the paint-this is required for all paints. 5) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. 6) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. 7) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. 8) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments Recommended Use :- It is recommended as primer on M.S surface for OEM's as well as for process industries like fertilizers, refineries, chemicals and other plants. It can also be applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. Physical Data :- COLOUR :- Yellow FINISH :- Matt SOLIDS BY VOLUME :- 40 �± 3% THEORETICAL SPREADING RATE :- 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ FLASH POINT :- Base : 23�°C Hardener : 23�°C DRYING CHARACTERISTICS :- SURFACE DRY : 60 to 90 minutes (At 30�°C & 65% Relative Humidity) :- HARD DRY : Overnight. FULL CURE : 7 Days SHELF LIFE :- BASE : 6 months HARDENER : 6 months SURFACE PREPARATION Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application Application Data MIXING RATIO :- Base : Hardener (As per our recommendation) APPLICATION :- By Brush / By Conventional Spray / By Airless Spray THINNER :- Epoxy Thinner 190 POT LIFE :- 4 hours min at 30�°C RECOMMENDED DFT :- 30 - 40 �µ. OVERCOATING INTERVAL :- MIN : 8 Hours MAX : 24 Hours COMPATIBILITY :- Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. . Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application:- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 1.4 mm Nozzle Pressure : 40 - 70 p.s.i. For Airless Spray Application:- Thinner : Epoxy Thinner 190 Addition : Max 5% Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
4.Main technical parameters 4.1. Capacity: 5, 10, 20, 25, 50100200kg (optional) 4.2. Unit switching: kg, N, LB 4.3. Load decomposition degree: 1/250,00 4.4. Load accuracy: 0.25% 4.5. Maximum stroke: 1000mm (excluding fixtures) 4.6. Test speed: 30-300 mm/min 4.7. Displacement resolution: 0.01 mm 4.8. Display device: touch screen (capable of displaying and printing test times, test values, maximum values, fracture values, etc.) 4.9. Motor: AC motor 4.10. Overall dimensions (L * W * H): 550 * 500 * 1240mm 4.11. Weight: 80kg 4.12. Power supply: 1 , 220V, 15A or specified 4.13. Delivery: One set of tension fixtures 5. Introduction to System Functions 5.1. It has tensile and pressure testing functions. 5.2. It has a pull stop function. 5.3. It can display displacement, has functions such as elongation, pressure, and other material testing machines. 5.4. There is an automatic stop alarm function for overload load setting. 5.5. It has an automatic save function, and can coexist with manual and automatic testing data up to ten times. 5.6. Use a list format to display the saved test data. 5.7. With an administrator password, users can modify their startup password to make machine management more secure. 5.8. Using software to calibrate the load value is extremely easy to calibrate. 5.9. The internal functions are set with full Chinese prompts, making the operation convenient and simple. 5.10. Rich testing functions, capable of conducting tensile tests, pressure tests, compressive tests, elongation tests, etc. 5.11. Display method: Real time display on the touch screen. 5.12. Tensile range: Standard configuration 200kg (optional). 5.13. The accuracy is 1/25000. 5.14. It can print test data and dates, making it easy to view test data for each stage 5.15. Conversion of three types of force units: N, Kg, and LB. During the testing process, 5 sets of test data at any position can be manually and automatically captured and printed. 7. Introduction This product tests the tensile strength, compressive strength, and elongation of various materials, semi-finished products, and finished products. It can perform tests such as peeling, tearing, bending, bending, and compression, and is suitable for use in industries such as metals, plastics, rubber, textiles, synthetic chemicals, wires and cables, leather, etc. 8. Design standards ASTM D903, GB/T16491, GB/T1040, GB/T8808, GB13022, GB/T 2790/2791/2792, CNS-11888, JIS K6854, PSTC-7, etc
Half Round Bars Most commonly used for Hardware purposes are very popular throughout the world. Technical Specification: SIZES: 12mm -25mm GRADES : AISI-201, 204Cu,304, 316 PSQ Pump Shaft Quality under the product DH produces PSQ bars in both Austenitic as well as Martenistic grades. Austenitic stainless steels are most commonly used. Austenitic stainless steel pump shafting is not magnetic; due to its high nickel and chromium composition, it is extremely resistant to corrosion. In addition, austenitic stainless steel pump shafting provides excellent mechanical properties. Heat treatment cannot be used to harden austenitic stainless steel pump shafting, although it can be hardened considerably by cold working. Grades Available in Austenitic Steel:- AISI-410 AISI-416 AISI-420 DH produces PSQ bars with superior finish and straightness tolerance by an additional process using modern techniques and state-of-art machinery and types of equipment including special finishing machines to give a smooth and mirror finish surface. Thus wear-free running of the impellers is ensured. DH also provides chamfering at 30- 45 degrees as per customer requirements. The bars thus produced undergo stringent quality and inspection test in order to ensure the exact technical requirements have adhered during the production as per O.E.M. specifications. Thereafter the bars are wrapped in HDPE sheets and then stuffed inside export-quality wooden boxes as per the specific requirements of the customer. DH also provides other types of packing like tube packing of each bar, putting 3-4 rubber/plastic "O" rings throughout each bar as per specific requirements from their customers. The details of such packing are precisely explained in our Packing segment under this website. Specification: Size Range : 10mm-70mm Diameter Tol. : h9, h8 Ovality: 1/2 the diameter tolerance Straightness: Upto 0.5mm per 1 meter Length : 2.5 meters - 6 meters Surface : Smooth / Mirror Finish The common application of PSQ Bars:- The PSQ bars are commonly used at following Industry levels:- Pneumatic and Hydraulic Cylinder Shafts Textile Machinery Shafts Piston Shafts Precision Shafting Chemical Pump Shafts
Deep groove ball bearings are available in radial and axial designs and are available in many different variants. Single row deep groove ball bearings are available in open and sealed designs. They are designed for high to very high speeds and can withstand radial and axial forces. Double row deep groove ball bearings are designed to correspond to single row deep groove ball bearings, and are used in situations where the radial load capacity of single row deep groove ball bearings is insufficient. NiuShang axial deep groove ball bearings are available in unidirectional or bidirectional design variants. These bearings are especially suitable for high axial loads. A deep groove ball bearing is a versatile type of rolling element bearing used in various applications to support radial and axial loads. It is characterized by its deep, uninterrupted raceway grooves on inner and outer rings, which enable it to accommodate high speeds and provide excellent performance. Key features and characteristics of deep groove ball bearings: Versatility: Deep groove ball bearings are suitable for a wide range of applications due to their ability to handle both radial and axial loads. They can accommodate moderate to high-speed operations and are commonly used in electric motors, automotive components, appliances, industrial machinery, and more. Radial Load Support: These bearings can primarily handle radial loads, which are forces acting perpendicular to the shaft. The deep groove design distributes the load evenly over a larger contact area, resulting in enhanced load-carrying capacity. Axial Load Capability: While deep groove ball bearings primarily support radial loads, they can also withstand some axial loads, which are forces acting parallel to the shaft. However, their axial load capacity is lower compared to other types of bearings specifically designed for heavy axial loads. Low Friction and High Efficiency: Deep groove ball bearings have low friction characteristics, allowing for smooth and efficient operation. This reduces energy consumption and heat generation, contributing to improved overall performance and durability. Quiet and Low Vibration: Deep groove ball bearings are designed to minimize noise and vibration levels during operation. This makes them ideal for applications where quiet operation is desired, such as in electric motors or precision machinery. Sealing Options: These bearings are available with various sealing options, such as rubber seals or metal shields. Seals help protect the bearing from contaminants, such as dust or moisture, ensuring longer service life and enhanced reliability. Maintenance and Lubrication: Deep groove ball bearings are generally low-maintenance components. Proper lubrication is essential to reduce friction and prevent premature wear. They can be lubricated with grease or oil, depending on the application requirements.
New HAYABUSA SUZUKI Motorbike/Motorcycle Leather Jacket Racing Biker Leather Jac Description Hayabusa Motorcycle Motorbike Jacket is especially designed for professional bikers to fulfill their biking passion on track with great safety. This jacket features excellent design & comfort, 100% genuine Cowhide leather, Approved internal & external Protectors on Shoulder, Elbows and Back, YKK Zippers for Performance, Full ventilated Chest to keep the biker cool while riding (Optional). Available in Men's Fitting and Women's Fitting. Available in all sizes, XS,S,M,L,XL,XXL,XXXL & Custom Size. Guarantee Triple seam (Stitches) which will never be worn or open the suit. 100% Original High Quality 1.3mm Cowhide Leather CE approved armors. Crashes prove (on and off the track). You may use same jacket for 4 to 5 crashes. Jacket might look bad because of some scratches but will never lose the shape or tear apart. Everything is in jacket is 100% A+++++ This suit is 100% for professional Bikers. We take care of every single little detail of jacket for professional bikers to have nice and smooth race. CE approved armors. Safety Features External CE Approved protectors on Shoulders, Elbows and Back Additional Rubber padding for safety on critical parts. Pr-Surved Sleeves for Proper riding Position Safety Seems (triple Stitch) YKK Zipper throughout Removable dual density armor at shoulders, and elbows. Removable dual density spine protector Ce approved Armors Customization Schoeller-Keprotec�® is optional for stretch material. Designing Facility Available for Men or Women in Tailor Made Custom Size Perforated Leather Panels for Embroidered Logos of any design desired Leather Patching Ventilation Zippers Comfort Collar Outer shell Genuine Cowhide Top Grain Leather 1.3 mm to 1.4 mm Pr-Surved Sleeves for Proper riding Position Original YKK Zipper at Front, Cuffs Stretch Material used in crotch, behind Calf and under sleeves for maximum stretch Safety Stitched Inner Shell 100% Polyester mesh lining Two inside pockets CE approved removable Protectors on Shoulder, Elbow CE approved removable Hump Safety Stitched Standard Size Chart & Tips To know best size we basically need your Chest,Waist,Hip & Full Length measurements. Some people who are really health or over weight, they have to go for custom fitting. we also offer any type of customization.
NEW VENOM MOTORBIKE MOTORCYCLE MOTOGP RACING BIKER LEATHER JACKET RIDER JACKET Description Ducati Motorcycle Motorbike Jacket is especially designed for professional bikers to fulfill their biking passion on track with great safety. This jacket features excellent design & comfort, 100% genuine Cowhide leather, Approved internal & external Protectors on Shoulder, Elbows and Back, YKK Zippers for Performance, Full ventilated Chest to keep the biker cool while riding (Optional). Available in Men's Fitting and Women's Fitting. Available in all sizes, XS,S,M,L,XL,XXL,XXXL & Custom Size. Guarantee Triple seam (Stitches) which will never be worn or open the suit. 100% Original High Quality 1.3mm Cowhide Leather CE approved armors. Crashes prove (on and off the track). You may use same jacket for 4 to 5 crashes. Jacket might look bad because of some scratches but will never lose the shape or tear apart. Everything is in jacket is 100% A+++++ This suit is 100% for professional Bikers. We take care of every single little detail of jacket for professional bikers to have nice and smooth race. CE approved armors. Safety Features External CE Approved protectors on Shoulders, Elbows and Back Additional Rubber padding for safety on critical parts. Pr-Surved Sleeves for Proper riding Position Safety Seems (triple Stitch) YKK Zipper throughout Removable dual density armor at shoulders, and elbows. Removable dual density spine protector Ce approved Armors Customization Schoeller-Keprotec�® is optional for stretch material. Designing Facility Available for Men or Women in Tailor Made Custom Size Perforated Leather Panels for Embroidered Logos of any design desired Leather Patching Ventilation Zippers Comfort Collar Outer shell Genuine Cowhide Top Grain Leather 1.3 mm to 1.4 mm Pr-Surved Sleeves for Proper riding Position Original YKK Zipper at Front, Cuffs Stretch Material used in crotch, behind Calf and under sleeves for maximum stretch Safety Stitched Inner Shell 100% Polyester mesh lining Two inside pockets CE approved removable Protectors on Shoulder, Elbow CE approved removable Hump Safety Stitched Standard Size Chart & Tips To know best size we basically need your Chest,Waist,Hip & Full Length measurements. Some people who are really health or over weight, they have to go for custom fitting
Motogp Redbull Customized Motorbike Cowhide Leather Racing Suit Description REDBULL Motorbike Racing Suit is especially designed for professional bikers to fulfill their biking passion on track with great safety. This suit features excellent design & comfort, 100% genuine Cowhide leather, Approved internal & external Protectors on Knee, Shoulder, Elbows and Back, YKK Zippers for Performance, Outer Knee sliders for performance. Full ventilated Chest to keep the biker cool while riding (Optional). Available in Men's Fitting and Women's Fitting. Available in all sizes, & Custom Size. Customization Schoeller-Keprotec�® is optional for stretch material. Designing Facility Available for Men or Women in Tailor Made Custom Size Desired Design is available in 1 piece Suit or 2 piece Suit. Perforated Leather Panels for Embroidered Logos of any design desired Leather Patching Ventilation Zippers Comfort Collar Outer shell: Top Grain Genuine Cowhide Mild leather 1.3-1.4mm Perforated (As per Design or on per customerâ??s desire) Sponsored Labels & Printings Stretch as per Design or on per Customerâ??s desire. Original YKK Zipper at Front, Cuffs & Calf External Shoulder, Elbow & Knee protections (As per Design or Customerâ??s desire) Dupont Kevlar or Schoeller Keprotec Stretch Fabric at inner arms and Crotch and Back Shin Areas (As per design) Coats Thread stitch Inner Shell: 100% Polyester mesh lining CE approved removable Protectors on Shoulders, Elbows, Knees, Back & Thighs CE Approved Hump Kevlar Thread Safety Stitch Material Composition: Leather = 50% Polyester Lining = 40% Foam Padding = 2% Rubber Padding =3% Zipper = 2% Thread = 3% Care Instruction: Do not iron Do not Machine Wash Do not Machine Dry Do not bleach Protect Against extensive sunlight, dryness & heat Product Hangtags: (1) Genuine Leather (2) CE Protectors (3) Kevlar or Keprotec Standard Size Chart & Tips To know best size we basically need your Chest,Waist,Hip & Full Length measurements. Some people who are really healthy or over weight, they have to go for custom fitting. Dispatch Time: We dispatch all items within 7 to 10 working days by DHL UPS Skynet FedEx Courier service as mentioned section. However, in busy times please allow 10 to 15 working days. Feedback: Feedback is very important to us and we ensure all our customers are satisfied with our products. If you feel that any part of the service is inadequate please contact us or email through eBay before leaving your feedback, we will guarantee a positive outcome. If you are not happy with anything please contact us before leaving negative feedback. Contact Us:
Polyester fiber sound-absorbing decorative panels with sound absorption, noise reduction, noise reduction, thermal insulation, thermal insulation, thermal insulation and other effects, the material is symmetrical and reliable, is a wide band of high-efficiency sound-absorbing materials. So how do you install a polyester sound-absorbing panel When installing the polyester fiber-absorbent panel wall with reserved back cavity, you can use straight clip type light steel keel to do the back attachment keel. In a good solid wall attached to the wall keel, the polyester fiber board with glue, or nail the method of connecting with the light steel keel. It has good flatness and stability. Directly affixed to the solid wall is as follows. 1. Pay attention to plate selection and plate-layout before construction. Pay attention to slight color difference, find out the center point of the paste surface, draw cross line, adopt the way of bricklaying, and start to line up the board from the center point (it is best to wear gloves to avoid pollution). 2.Cut the board surface Use steel ruler and sharp knife to cut or decorate accordingly, if you want to reduce the seam, you can tilt the blade inward by 0.5 1mm when cutting to facilitate the board edge butt, and reduce the gap. 3.Paste (1) Cement or wood base surface: can choose non-benzene universal glue or white latex made of neoprene rubber. (2) Base surface of paper gypsum board: under the premise that it is not easy to be damp, you can choose white emulsion glue or wallpaper glue made of cellulose as raw material (should be fixed with nails immediately after gluing to avoid the glue is not dry and the board surface moves). (3) Under the premise of easy or possible moisture, you can use universal glue. Polyester fiber sound-absorbing panels are porous sound-absorbing materials, it is easy to absorb glue, blocking holes, affecting the cavity after the sound-absorbing function. It is recommended that when constructing, you can brush glue on one side (only brush glue on the base plate or keel, the amount of brush glue is slightly heavier than normal). At the same time, you can also match the grain nail reinforcement. V-groove wall panels are CNC machine-cut to create 45 90 grooves in the surface of the PET acoustic panels. The paper size can be customized. It is widely used as a wall panel in wall spaces. Our Poly acoustic panels are made from recycled PET, which is also fully recyclable for complete acoustic panels, and we can cut CNC cut and UV printed panels on the surface that are lightweight, fire resistant, impact resistant, tacky, easy to install, and most importantly have high acoustic performance.
Stainless steel pleated filters cartridge is a type of filter element that is made from stainless steel and designed with a pleated structure. The pleats increase the surface area of the filter, which provides more capacity for capturing contaminants. Stainless steel pleated filter cartridge is known for their high strength, durability, and resistance to heat and corrosion. They are commonly used in industrial applications where high-performance filters are required for filtering fluids and gases. parameters Material:stainless steel304, 304L, 304HC, 316, 316L, 321, 430 or as per you request. Filter rating 1-300 microns Flow rate: 80-200l/min Working pressure:1.5 bar-250 bar Working medium:The common polymer industrial, included rubber, plastic, liquid emulsion,etc. Working temperature: 600 Features 1.High Strength Against High Differential Pressures: These filters can withstand high differential pressures without loss of their filtration efficiency or structural integrity. 2.Large Surface and Filtration Area: The pleated design of these filters results in more pleats in the stainless steel filter, which means a larger surface and filtration area. This provides a greater ability to capture contaminants. 3.Washable and Reusable: The stainless steel filter element is washable and reusable, which prolongs its service life and reduces the frequency of filter replacement. This saves money and reduces waste. 4.Excellent Heat and Corrosion Resistance: These filters are highly resistant to heat and corrosion, making them suitable for use in harsh environments where other filters may fail. Applications Oil and gas production: are used in the oil and gas industry to filter out contaminants from crude oil, natural gas, and other fluids. Chemical processing: These filters are used in chemical processing to remove impurities from chemicals and solvents. Water treatment: are used in water treatment plants to remove sediment, debris, and other contaminants from the water supply. Food and beverage production: These filters are used in the food and beverage industry to filter out impurities and ensure product quality. Pharmaceutical production: are used in the pharmaceutical industry to filter out contaminants and ensure product purity. Automotive and aerospace industries: These filters are used in the automotive and aerospace industries to filter out contaminants from hydraulic fluid, lubricating oil, and other fluids used in machinery. Industrial air filtration: are used for industrial air filtration to remove dust, smoke, and other airborne contaminants from the air.
We are the world's top supplier of V-belts. Our main products are V-ribbed belts, automotive timing belts, industrial timing belts, V-belts, toothed belts, etc. Our advantage -- Our products use a new production process -- Our products can be clothed on the top layer to increase life -- We are factories, so the price is cheap -- The main material is oil-resistant and high-temperature-resistant composite rubber -- We have cooperation with major markets and can provide common models -- High transmission efficiency -- Low noise -- Low elongation and high load -- Long life, not easy to wear -- Oil resistant and high temperature resistant -- New vulcanization technology Title goes here. * package: bags or cartons * carton dimension: 65*37*26cm * delivery days: 30 days but also according to you quantity * Packing information: PP/CARTON, it depends on customer's requirements. * Shipping condition: LCL, FCL or EXPRESS. * Quote item: FOB / EXW / CIF / CNF. * Port: Tianjin Port * Lead Time: Shipped in 30 days after payment. FAQ Q1:Can i order a small quantity of samples? ---- Yes. We can offer you samples at the bulk prices and send them by DHL, TNT. EMS, FEDEX or others according to your requirements. Q2: How could i know whether the belt fits for my machine? ---- You can tell me which product you are interested in, and i will give you its main sizes. You can also send me drawings or samples, and then we will put them into production at your requests. Q3: I want to find a supplier for my new products. Can you help me? ---- Yes. Kindly offer me your drawings or samples for analysis. Q4: How long does it take to make a new product? ---- Usually 10-15 days for drawings and 7 days for samples. Q5: Can we stencil (or print ) our logo or company name on the belt or package? ---- Yes. Please inform us your logo or design before mass production. Q6: What is your payment term? ---- T/T 30% deposit and T/T 70% balance before shipment. Q7: What is your quotation? ---- We will give you FOB price. But EXW, CIF and CNF can also be given according to your demands.
We are the world's top supplier of V-belts. Our main products are V-ribbed belts, automotive timing belts, industrial timing belts, V-belts, toothed belts, etc. Our advantage -- Our products use a new production process -- Our products can be clothed on the top layer to increase life -- We are factories, so the price is cheap -- The main material is oil-resistant and high-temperature-resistant composite rubber -- We have cooperation with major markets and can provide common models -- High transmission efficiency -- Low noise -- Low elongation and high load -- Long life, not easy to wear -- Oil resistant and high temperature resistant -- New vulcanization technology Title goes here. * package: bags or cartons * carton dimension: 65*37*26cm * delivery days: 30 days but also according to you quantity * Packing information: PP/CARTON, it depends on customer's requirements. * Shipping condition: LCL, FCL or EXPRESS. * Quote item: FOB / EXW / CIF / CNF. * Port: Tianjin Port * Lead Time: Shipped in 30 days after payment. FAQ Q1:Can i order a small quantity of samples? ---- Yes. We can offer you samples at the bulk prices and send them by DHL, TNT. EMS, FEDEX or others according to your requirements. Q2: How could i know whether the belt fits for my machine? ---- You can tell me which product you are interested in, and i will give you its main sizes. You can also send me drawings or samples, and then we will put them into production at your requests. Q3: I want to find a supplier for my new products. Can you help me? ---- Yes. Kindly offer me your drawings or samples for analysis. Q4: How long does it take to make a new product? ---- Usually 10-15 days for drawings and 7 days for samples. Q5: Can we stencil (or print ) our logo or company name on the belt or package? ---- Yes. Please inform us your logo or design before mass production. Q6: What is your payment term? ---- T/T 30% deposit and T/T 70% balance before shipment. Q7: What is your quotation? ---- We will give you FOB price. But EXW, CIF and CNF can also be given according to your demands.
