Addition cure Electronic Potting Silicone Rubber 1. Product Feature of Addition cure Electronic Potting Silicone Rubber Electronic Potting Silicone Rubber is a kind of low viscosity, Inherent flame resistance, two components addition cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)ã?�PPã?�ABSã?�PVC, etc. and metal materials. 2. Typical Application of Addition cure Electronic Potting Silicone Rubber HY-9055 electronic potting silicone rubber could be applied to - high powered electronics, - DC/DC module and circuit board which requires heat dissipation and high temperature resistance. -It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc. 3. Technical Guidelines of of Addition cure Electronic Potting Silicone Rubber a, Pls put part A and part B in separate container and stir evenly before mixing the two part together. b, Mixing Ratio: part A: part B = 1:1 c, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring. 4.Notes of Addition cure Electronic Potting Silicone Rubber a.The following material may hinder the curing of HY-9055, So pls use after the test. When necessary, pls clean the application areas. Organotin compound or Condensation silicone with organotin Sulphur, sulfide and sulfur rubber materials. Amine compounds as well as contains the amine materials. Pewters solder flux b. HY-9055 should be sealed storage.The mixture should be used up disposably to avoid causing waste. c. HY-9055 belongs to non-dangerous goods, but keep away from mouth and eyes. d. When it gets stratified after a period of storage, Please mix it evenly before using,which does not affect the performance. PACKAGE 40Kg/pail as a set (Part A 20Kg + Part B 20Kg) SHELF LIFE AND TRANSPORTATION 1. Twelve(12) months when stored at 24C in tightly closed original packages. 2. This kind of product is non-dangerous product, which could be transported as general chemicals. 3. Storage beyond the expired date doesnot necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons. -
liquid silicone has a wide range of uses. We contact many things in daily life, such as baby pacifiers, coasters, medical supplies, silicone mobile phone cases, etc.
Silicone rubber for mold making is primarily intended for poly resin crafts, pu crafts, pu resin crafts , gypsum crafts , unsaturated resin crafts, lighting and candles crafts , plastic toy , stationery gifts crafts industry, a large statue buddha, furniture, furniture decorative materials, statues buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils factory, europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on. 25kg/drum and 200kg/drum
1.Application of brushing rtv-2 molding silicone rubber : Brushing rtv-2 molding silicone rubber mainly used for shoe molds, sand casting, sole sampling, plaster models, simple products, products with non-complex patterns, as well as product models with stable size and non-deformation. 2.Operation instruction of brushinng silicone rubber : Brushing rtv-2 molding silicone rubber is composed of two components.Component a is white flowing liquid while component b is the curing agent. Steps: A. Take silicone rubber of 100g and add 2% curing agent for mixing evenly. B. After the silicone rubber and the curing agent are completely mixed, put the silicon into a vacuum machine for deairing to remove the bubbles. C. After deaired, pouring the liquid silicone rubber into the product to be duplicated or into the mold frame. Note: brushing rtv-2 molding silicone rubber is used for pouring or brushing technique. That is to say, Firstly fix the product or sole model to be duplicated onto a plane plate, Then enclose the plane frame with wooden plates to prevent the leakage of the silicon , Thirdly mix the silicone rubber and the curing agent evenly according to the mixing ratio of 100: 2 and pour them onto the sole model, At last brush evenly with a wooden plate or a brush, and fill up the mold frame with gypsum after the silicone rubber is dried. 3. Storage and precautions of brushing molding silicone rubber : 25kg/drum, 200kg/drum
Description of rtv silicon rubber: Silicine rubber for manual moid is flowing liquid with consistant quality in whatever color. It consists of two components, wherein component a is silicone rubber, and component b is curing agent or vulcanizing agent. Firstly process and prepare the model mold or the product to be duplicated, take certain amount of the silicone rubber, add 2-3% solidifying agent, and mix evenly for use. One mold pair can be solidified and formed in 2-3 hours. The formed mold can be used repeatedly without deformation and water shrinkage and with high temperature resistance, thereby providing fast duplication of the product with a product shrinkage 2. The 418 manual mold silicon is mainly applicable to manual molds and small number of product duplication. 25kg/drum, 200kg/drum
Rtv-2 room-temperatue sulfureted silicon rubber Silicon flexible molds are used for mold duplication and delicate mold making for poli crafts, resin crafts, lighting and candle crafts.
Place of origin: guangdong, china (mainland) Brand name: laimeisi Model number: lms Application: fiberglass mesh cloth Weight: 158 gsm - 1740 gsm Surface treatment: silicon coated Width: 300~600mm, 300~600mm w Eave type: plain woven yarn type: c-glass Alkali content: alkali free Standing temperature: -40?~260? Hardness: 70shore Specific gravity: 1.6~2.3g/cm3 Size: 50m/roll Thickness: 0.2~3.0mm Flammability: ul94v-0 Continuous use temp: -40?~260? Rohs: pass Color: pink, blue, grey
Sponge Foam Waterproof Rubber Seal Strip Gasket for Doors Quick Details Place of Origin: Guangdong, China (Mainland) Brand Name: laimeisi Model Number: LMS Application: Glass Window Technology: Extruded Color: White Density: 0.4~0.8 g/cm3 Size: Custom Size Length: As Requested Thickness: 0.2~0.45mm Use Temperature: -40~200â?? Certification: ROHS Product Name: Sponge Foam Waterproof Rubber Seal Strip Gasket for Doors Materialï¼? Foam Silicone Rubber Colorï¼?White Red Working Temperatureï¼?-40~200â?? Feature 1. Can maintain its original high sealing performance under High/low temperature. 2. Ozone and waterproof performance 3. Excellent weather resistant and water resistant 4. Good elastic and Anti-aging 5.Non-toxic, safty and healty 6. dust-resistant and oil-resistance ,will never deformation 7. To meet your specifications and improve your product performance Application Sealing door and window,avoiding noise, anti-explosion purpose; Used in boat,car,electrical machine,etc Packaging Details Red Silicone Sponge Adhesive Backed Waterproof Foam Rubber Foam Sheets Insulation Roll Sheet 1mm Delivery Time Shipped in 7 days after payment Port:Yantian Lead Time :Shipped in 7 days after payment
ISO,Reach, Rohs,ASTM stander Stander size and customized sizes available Different types and customizing design are available! Suitable for any application. Material from silicone,nr,nbr,sbr,epdm, to any rubber! Competitive price in this industry!
We provide all kinds of liquid silicone rubber,molding,casting,electronic potting,pad printing,foam rubber,silicone for dildo,medical,label,leather,injection etc. Hong Ye Silicone have 23 years experience in silicone research and producing! A little higher price,much better quality! Do not focus only on price if you don't want lose your faithful customer!
Place of origin: guangdong, china (mainland) Brand name: laimeisi Model number: lms Application: fiberglass mesh cloth Weight: 158 gsm - 1740 gsm Surface treatment: silicon coated Width: 300~600mm, 300~600mm w Eave type: plain woven yarn type: c-glass Alkali content: alkali free Standing temperature: -40?~260? Hardness: 70shore Specific gravity: 1.6~2.3g/cm3 Size: 50m/roll Thickness: 0.2~3.0mm Flammability: ul94v-0 Continuous use temp: -40?~260? Rohs: pass Color: pink, blue, grey
We are a leading manufacture of rubber products of china. Our company provides high-quality and low-price rubber products. We custom, mold and extrude rubber products. Our products are quite competitive in the development of special rubber products such as silicone, EPDM, fluoric rubber. We sincerely hope that we can be your best partner in China. Our company's products have been exported to middle east, Europe, and other countries and enjoy high reputation worldwide. Welcome to contact us for further discussion. According to your requirement
Silicon rubber 20kg boxes
Material:rubber/silicone Type:stress ball Style:soft toy Place of origin:haining, china (mainland) Brand name:huajiao Model number:b 001 Function:wearable, movement, good bouncy/hardness, shock resistance, oilproof Use:valve, pump, electrical, industry, ibrating screen, etc. Name:high bounce ball rubber ball for coin machine Material:nr, nbr, sbr, epdm Color:black or as your requirement Size:customized Shipment:by express or logistics or sea Hardness:20 to 95 Express:ups, tnt, fedex -
INTRODUCTION: The component A of shoe Mold Silicone Rubber is white flowing liquid and the component B is the curing agent. For example, take silicone rubber of 100g and add 2% curing agent for mixing evenly. After the silicone rubber and the curing agent are completely mixed, put the silicon into a vacuum machine for deairing to remove the bubbles. After deaired, pouring the liquid silicone rubber into the product to be duplicated or into the mold frame. FEATURES: 1.Two-component silicone rubber with tin-catalyst 2.Cured under room temperature 3.Low shrinkage 4.Excellent fexibility & easy demould LIQUID RTV-2 SHOE MOLD SILICONE RUBBER NOTES: Shoe mold silicone rubber is used for pouring or brushing technique. That is to say, fix the product or sole model to be duplicated onto a plane plate, then enclose the plane frame with wooden plates to prevent the leakage of the silicon , mix the silicone rubber and the curing agent evenly according to the mixing ratio of 100 : 2 and pour them onto the sole model, then brush evenly with a wooden plate or a brush, and fill up the mold frame with gypsum after the silicone rubber is dried. APPLICATION: Shoe mold silicone rubber is mainly used for shoe molds, sand casting, sole sampling, plaster models, simple products, products with non-complex patterns, as well as product models with stable size and non-deformation. ABOUT US: We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber. What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us. For more information, welcome to contact Lilian: Wechat / Phone: 8613617490457 E-mail: lilian(at)xrsil(dot)com Skype: lilian-xrsilicone Company: Dongguan Xinrun Silicone New Materials Co., Ltd Xinrun Group Limited Factory address: No.2,Zhouliao Road, Langzhou Industrial Zone,Changping, Dongguan, Guangdong, China
KEY FEATURES: 1. High transparence 2. High tensile strength 3. Good rebound property 4. Outstanding resistance to ageing 5. Low shrinkage 6. Non-discoloring 7. Excellent thermal and cold stability APPLICATIONS: The series are suitable for making baby nipples. PACKAGING: It is available in 20kg pails of 200kg drums TYPICAL PROPERTY: Appearance: Transparent; Viscosity (mpas): 650,000~950,000; Hardness: 20~70 Shore A; Tensile Strength: 6.5~8.5 MPa; Tear Strength: 20~35 KN/m; Elongation at break: 330%~800%; Linear shrinkage: 0.1% REMARKS: The product should be closed tightly, protected from light and moisture, the shelf life is 12 months These figures are for reference only, please contact us for detail. 20 KG/drum
Application of rtv-2 mold making silicone rubber: Rtv-2mold making silicon rubber and silicone rubber are general called two-component room temperature vulcanization silicone rubber with excellent fluidity and good operational performance. An elastic silicon mold will be obtained with resistance to deformation, high-temperature, acid and alkali and expansion. Description of rtv-2 mold making silicone rubber: Rtv-2molding silicon rubber is mainly applicable to mold duplication of poly crafts, resin craftworks, lightings, candles, etc. And fabrication of precision molds. Feature of rtv-2 mold making silicone rubber: 1.Rtv-2 silicon rubber:flowable liquid silicon and curing agent. 2.Rtv-2 silicone rubber cures at room temperature within 2-4 hours. 3.An exceptional fluidity and good operability, easy to demold. 4.Good tensile and tear strength, low shrinkage. 5.High duplication times. Model number: 620 628 638 640 Fob price: usd7.0~8.5 Port: shenzhen Min: 100kg Supple ability: 4ton/per day 25kg/drum and 200kg/drum.
The pad printing silicon rubber usages: The silicon rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys, trade makers .Silicon pad printing is a carrier which transfer printing the patterns on the steel plate onto the toys products surface. Pad printing silicon rubber features: Pad printing silicon rubber with high print times and abrasion resistance, without any inpurities, with good printing effects, permanent and durable, we can provide all kinds of colors are available and our catalyst is free charged. Pad printing silicon rubber operation instructions: Pad printing silicon rubber is two-component silicone, part a is the liquid silicon rubber, part b is the catalyst. The usual mxing ratio for silicone rubber and catalyst is 100 : 2-3, eg. We take 100grams of liquid silicon rubber, then we add 2-3 grams catalyst, mix then evenly and pour it to your mold. Then after 2-4 hours, you will obtain a printing pad. Frequently asked question of pad printing silicon rubber: The reasons why the silicon pad has a short service life are listed as follows: (1)the problem caused by inappropriate filtration of silicone rubber, and impurities in the packaging process due to the uncleanness of barrels and bags. (2)the short service life of the silicone pad has a close relationship with the adding amount of silicone oil. The more the silicone oil added, the softer the silicone pad will be. The silicone oil will destroy the molecule of the silicone rubber, thereby bringing about the non-durable and easy ageing of the silicone pad.
We have two models on this series , hy968 and hy988 respectively.The model of 988 is a kind of high temperature addition cured silicon rubber with platinum catalyst.It is mainly designed for metallic arts&crafts and food grade mold making.It features with resistance to high temperature up to 300 centigrade to 500 centigrade, which makes up for those products impossible produced by press machine and fills the blank for large lead-zinc alloy crafts and fine pattern products.It is the most advanced htv-2 high temperature silicon in china and the best option for lead-zinc alloy crafts. Rohs.Msds.Sgs iso9001:2000
