DESCRIPTION Bituminous Primer is product containing oxidized bitumen and a mix of technical quick drying solvents. APPLICATION Bituminous Primer is recommended to block the dust and the porosity of concrete surfaces allowing the quick application o f the bituminous polymer membranes, both with flame application and cold bonding with bituminous sealants or with self adhesive membranes.Bituminous Primer allows quick film drying, has an excellent penetration and adhesion to the support for the absence of surface stickiness. INSTRUCTIONS FOR USE Concrete surfaces must be dry, clean and free from oil, dust or release agents. This type of primer is ready for use after mixing it. Bituminous Primer can be either sprayed or applied by means of roller or brush. In case of hot application of membranes with flame, the primer can be used only if surfaces are completely dry. On the contrary, if the surface is damp, it is recommended to use a bituminous primer specific for damp surfaces. The drying time depends on concrete porosity, on the quantity of product applied and on the temperature of both the surface and the environment. Usually the film gets dry after 2-4 hours from the application. The drying time can increase in case of cold temperature and with low a bsorption surfaces. PACKING 5 gallon Bucket SHELF LIFE The product can be stocked in closed buckets and in dry area, far from UV rays for 12 months. TOOL CLEANING After use clean tools with common solvents.
Description CC-401 is a water based reinforced with acrylic polymers and graded fillers primer for concrete and masonry surfaces in order to improve adhesion between the substrate and subsequent coats. Appropriation For Rockflexï¼?RCï¼?Masonry System Characteristics Ready to useï¼?Easy to apply Improves adhesion Improves the finish of topcoat Non-toxic Surface preparation: Concrete substrate shall be dry, sound, clean and uncontaminated. All loose particles, curing compound, shuttering oil, debris etc shall be removed. Temperature Condition: Ambient temperature shall be between 10 and 50 °C Application: CC-401 is applied at 4 - 6 m2/ltr depending on substrate porosity and allowed to cure for 2 to 4 hours at 25 °C before over-coating with Rockflex systems Cleaning: Clean the tools with water immediately after use. Packing and Storage CC-401 is available in 20 ltr pack and it shall be stored in cool, dry and shaded warehouses. Shelf life is 12 months when stored under cover, out of direct sunlight, protected from extreme temperatures and as per manufacturers recommendations. In extreme tropical climate, the product shall be stored in cooled ambience. Excessive humidity and over exposure to UV will result in the reduction of shelflife.
PREPARATIONS The substrate, bolt and anchor holes must be clean, sound, dry and free of oil, grease, without laitance and loose particles. Prewet the bolt holes thoroughly, but no standing water in it. Before applying ITLS CA-007H absorbent substrates must be saturated thoroughly, but without standing water. MIXING Mix 3.2-4.4 liters of clean water with 25kg bag of ITLS CA-007H together. To add water based on the condition of stirring and keep stirring around 5 minutes until grouting well. APPLICATIONS Pour ITLS CA-007H mortar after mixing into the reserved cavities and recesses use the stick or bar to remove the air bubble, ensure that air entrapped into the grout is allowed to escape. Suggest to blend the grout by auto-mixer for better application. COVERAGE 25 Kg ITLS CA-007H when mixed with water will produce approx. 13.5 liters of Liquid Grouting Mortar. ITLS CA-007H suggest to be placed in thickness ranging from 10-15cm/layer.
Features * With excellent adhesion, non-sagging and construction resistance. * Without cracking and bulging after curing. * Specific design for spray plastering. * Applying by spraying machines efficiently. * Suitable for tiling. * Interior wall, exterior wall, panel wall and small area ceiling rendering. Application 1. Substrate must be free from grease, mould oil, rust, rusty metal , wood peels, paints, plastics, loose particles, contamination on any traces of foreign materials affecting the adhesion of CS-010. 2. Moisten the substrate overnight and also at the time before the commencement of operation. 3. Suggest to use CC-400 Concrete Bond as primer to adding adhesion for smooth and low porous substrates. 4. CS-010 is suitable for any type of spraying machine. Mix a packet of 40KG powder with 6.4liter of water and stir well for use. Its thickness should be maintained at 15mm and wait for 6-24 hours to apply for increasing the thickness. Storage Storage life is 12 months if the product is kept in a dry place. Package 40kg/powder bag
DESCRIPTION CC-102 Concrete Hardener is a clear high performance waterborne liquid which being applied to the floor and absorbed into the concrete pores and reacts with the calcium salts effectively making the concrete surface denser and considerably less porous. APPLICATIONS Suitable for improving the quality of concrete floors in factories, warehouse and any other area where hard non-dusting floors are important. SURFACE PREPARATION Surfaces should not have had previous treatments. They should be firm and free from oil, dirt, dust etc. Weak spots should be cut out and filled with CEMCRETEâ??S FLOOR PATCHING. All surfaces to be dry at time of application. MIXING AND APPLICATION Shake or roll drum to thoroughly mix contents. Apply HARDENER to the dry surface using a soft household broom or paint roller. Application should be liberal but it is advisable to brush away unabsorbed pools immediately to avoid the HARDENER forming glassy layers. Allow one day between coats. Two coats are usually sufficient, but a third might be required if the concrete is very porous SPECIMEN FINISH A trial area should be treated on site for the Engineerâ??s or Architectâ??s approval. COVERAGE Depends upon the suction and texture of the surface. Approximately 6m2 / litre/coat.
DESCRIPTION HYPERCOAT-518 is a premium, semi-thixotropic, liquid-applied, highly permanent elastic, cold applied and cold curing, one component synthetic rubber membrane used for long-lasting waterproofing. HYPERCOAT-518 is solvent based, cured by reaction with ground air moisture. And itâ??s semi-thixotropic for use in sloped surfaces. APPLICATION â?? Concrete Roof, balconies, terraces and verandas â?? Wet areas (under-tile) in bathrooms, kitchens, balconies, auxiliary rooms, etc. â?? Pedestrian and vehicular traffic decks â?? Green roofs, flowerbeds, planter boxes â?? For repair old bitumen felts, asphalt felts, EPDM and PVC membranes and old acrylic coatings. â?? Waterproofing and protection of concrete constructions like bridge-decks, tunnels, stadium stands, car parks, etc. Product properties â?? Long lasting performance with acidity and alkaline â?? Good resistant with oil, bitumen, wax â?? Strong adhesion with metal and concrete substrate â?? One component products, easy to apply and suitable for various tooling â?? Elongation more than 700%, tensile strength more than 70kgf/cm2, â?? Penetration strength more than 25kgf/cm2, tear strength more than 40kgf/cm
DESCRIPTION ITSEAL is truly developed for sealing window frames with highly durable and flexible properties to withstand severe weathering and extreme temperatures. It seals small gap that normal sealant cannot reach and penetrate. It provides a truly watertight seal deep into minute joint and gap. FEATURES * ITSEAL is the only waterproof sealer that is completely watertight. * It is highly water repellent that no water can get through it during storm. * It adheres well on aluminum and glass * Once dried, ITSEAL is flexible and accommodate joint movement due to vibration. * Mill finish aluminum, oil or wet surfaces can also be well-sealed. VOC CONTENT Type of Regulated Adhesive under the Air Pollution Control (Volatile Organic Compounds) Regulation of Hong Kong: Architectural Sealant VOC Content (Ready to use): 248g/Ltr. SURFACE PREPARATION For maximum adhesion, the adhesive surface must be free of dust, release agent, oil and grease. Wipe surface with solvent is recommended. Solvent are obtainable from ITLS-SB. This information in this catalogue is provided to the best of our knowledge from results gathered both internal and external credited laboratories. However, we have no control over site applications, site conditions and workmanship of the applicator. We therefore will not accept any liability, either directly or indirectly arising from the misuse of these products or when the product is used not in accordance with any advice, specification, and recommendation of information given by us, The user is responsible for checking the suitability of these products for its intended use. APPLICATION ITSEAL can be used with hand operated or air operated grease pump. Other simple extruding device can also be used but it has to be solvent resistance. LIMITATION * Not suitable large gap wider than 5 mm wide and deep. For deeper joint fill to half of it, let it dry overnight and fill it up the next day. * Not suitable for use as expansion joint. COLOUR AND PACKING 26 kg / pail Grey/Black/Bronze/White SAFETY INFORMATION * ITSEAL is flammable. Please keep away from sources of ignition during application. * Avoid breathing in solvent by wearing solvent vapor respiratory mask in badly ventilated area or confined space. * Avoid contact with skin and eyes. If swallowed please contact doctor immediately. * ITSEAL meets the requirement of RoHS regulation of European Union and it does not contain eight heavy metals which were restricted by ASTM F963 or EN71 part3. * Please read the Material Safety Data Sheet in regards to flammability and health and hazard. SHIPPING/STORAGE INFORMATION ITSEAL must be stored in a cool place under 25°C and away from direct sunlight. The shelve life is 12 months if stored in accordance to the recommendation. Dangerous Goods Information: Cement Adhesive, Class 3, UN1133 PG III.
DESCRIPTION ITLS PMS 60 is a single component elastomeric sealant without isocyanates. It cures rapidly under the effect of atmospheric humidity to form a flexible and resistant joint with very good adhesion on most materials. APPLICATION ITLS PMS 60 is suitable for industrial and refrigerated trailers, truck bodies, shipbuilding, air conditioning and ventilation units, sandwich panels and other industrial applications. ITLS PMS 60 can also be used for bonding and caulking different materials used in the building industry : concrete, wood, aluminum, most lacquered metals, polyester, glass, stone, ceramic, and so on. However, for difficult materials especially lacquered or non-ferrous metals, it is necessary to make tests beforehand. INSTRUCTIONS FOR USE SUBSTRATE PREPARATION: The substrates must be clean, even, dry, free of dust, oil, grease and any contaminants that could harm bonding. All traces of poorly adherent paints or coatings should be systematically removed beforehand. They may be cleaned with PMS primer, methylethylketone (MEK) or acetone. Check the compatibility of the solvent used with the substrates. It may be necessary to rub down the substrate beforehand. After rubbing down, the surface should be recleaned. Allow the substrate to dry after degreasing. When using solvents, extinguish all sources of ignition and carefully follow the safety and handling instructions given by the manufacturer. CAULKING: ITLS PMS 60 can be applied by a manual or pneumatic gun. After application, use a putty knife to smooth the joint with soapy water. Do not apply at a temperature under 5 C. In cold weather, store the cartridges at about 20 �°C before use. This product should be used within 24 hours of opening the cartridge protection; otherwise, the sealant could harden inside. Avoid any contact with non-cured polyurethanes during curing. CLEANING: Tools can be cleaned with PMS primer, MEK or acetone before the sealant has completely cured. After curing, abrasion is necessary. STORAGE AND SHELF LIFE 12 months in the original, hermetically sealed packagings between 5 and 25 C PACKAGING 290 mL cartridges and 600 ml sausages SAFETY Not classified as hazardous. Read the material safety data sheet before use.
DESCRIPTION CC-200 is a indoor, high fluidity, rapid strength and leveling material. It still has high bonding,low shrinkage, low water absorption, acid resistance, alkyl resistance and chemical resistance. It special use for fast repairing, putty and leveling for epoxy coating. APPLICATION Floor fixing on parking garage, factory, and warehouse. Leveling before epoxy coating. Basic layer for non natural paint. Bec ause of the early strength and low moisture content, CC 200 has widely application. Contact out agent when you have doubt on CC 200. ADVANTAGES 1. Curing and enhancing are fast and rapid below 25 mins. High strength and low water absorption/ content could be reached after curing. 2. Good acid and alkyl resistance. 3. Good wear resistance, high compressive strength, leveling and anti cracking. PREPARE TO USE 1. Clean with vacuum to ensure the surface dustless. 2. Working site is free from dust, sand, oil, and loose. a). Crack and Joint Treatment b). File on the crack, open a width of 2 3 cm depth of 1 cm or more groove joints and clean up dust and loose. c). At the same time taking CC 200 mortar, filled in and up the crack and sizing 1 2 times primer after 2 4 hours. 4. Shorter wor king hours to achieve saving time, fast leveling and convenience work.
Description 1. Tough film and good adhesion on the concrete, able to penetrate into concrete. 2. Good resistance to water , brine and chemicals. Excellent mechanical strength and physical properties. 3. Good resistance to impact and abrasion. 4. Easy application , drying fast. Prepare to use 1. Mix base and hardener by the mixing ratio and Stir thoroughly, then setting at least 15 minutes. Thinner may be used to reduce viscosity. 2. Remove all foreign particles, oils, grease , rust and moistures from the surface before application. 3. Two packs product, must be used completely during the duration of its pot life. 4. Donâ??t apply when the temperature is < 10â??,>40â??, relative humidity is >90â?? or the surface temperature of substrate is not higher than the dew point for at least 3â??. 5. If the coating interval is exceeded , the surface of base coat must be roughened to insure adhesion. 6. Keep away from heat, sparks and flame. 7. Stored with good ventilation. 8. Keep adequate ventilation during application. 9. The actual coverage may vary, depending on application technique, job conditions and type of surface. Under brushing & rolling application the actual coverage is estimated at 70% of the Theoretical coverage and 60% for spraying. **The parts of data base above could be affect by application condition at job site, please reference guide specification or contact with relative technical personnel. Color : Clear Drying time : Tack-free : 2 hours Hardness : 8 hours Full cure : 7 days (grease)
DESCRIPTION CP-310 was synthesized from imported high-technology macromolecule resin and specialized paint that is different from general acrylic resin. CP-310 is a perfect product to provide a high water-tolerant, climate-tolerant, and anti-UV ability. FEATURES * Excellent environmental water-based waterproofing paint * Water-based, Non-toxic, odorless, inflammable, and harmless * Fine adhesion, extreme toughness, high elastic, and high endurance * Hydrophilic, and may be applied on damp surface USE RoofBuilding, condominium, factory, barracks, school, garden and etc.. WallsBasement wall , exterior wall , and etcâ?¦ PREPARATION 1. (The following steps are recommended for best results) 2. New concrete must cure for a minimum of 30 days 3. All holes or cracks must be properly patched 4. All surfaces must be clean and free of dirt, dust, efflorescence and oil APPLICATION (The following steps are recommended for best results) 1. Stir well before use. Do not thin; however, if thinning is necessary, thin water at a rate of no more than 10% 2. One prime required CP-310 primer 3. Two coats are required for the best resultskeep the thickness of each coating below 1m. 4. Wait for each coating to be total dry before overlaying the next coat. The interval time between each coating is minimum of 8 hours. COVERAGE 5-gallons about 33m2 COLOR Grayã??Whiteã??ivoryã??Green DRY TIME Dries to touch in about 1-2days . Low temperatures or high humidity conditions will affect drying time. Full cure should be reached in 14-30 days. CLEAN UP 1. Clean hands and tools with soap water. 2. After 30 days or paint has fully cured, areas may be wasted using a non-abrasive, mild detergent and cellulose sponge. WARNING (Read the following carefully for your own safety) 1. Keep out of reach of children-Do not take internally. 2. May cause eye, skin and respiratory tract irritation. May be harmful if swallowed. Use only with adequate ventilation.
DESCRIPION FR-48 is solvent-less moisture cure type, single-component flame retardant RTV silicone product. It is suggested for use in applications requiring neutral cure, fast cure and excellent adhesion. FEATURES * Sealing of electrical components * Industrial plastic sealing, electrical insulation properties. * Low flammability â?? has a UL rating of V-0(1) * Primerless adhesion to plastics and metals * Excellent resistance to moisture, dust, UV and ozone. * Fast room temperature curing * High temperature resistance (Flexible from -60â?? to 200â?? continuous operation and 260â?? for short periods) COMPATIBILITY FR-48 contamination -free silicone sealant shows excellent adhesion for Al panel, stone, glass, PVC, or wood. As new construction materials appear and the material surface treatment method varies, some materials may cause poor adhesion or discoloration. FR-48 contamination-free silicone sealant is chemically stabilized, maintains a uniform paste shape all the time, and may be workable at the temperature range of -25â??~50â?? unless there is moisture. LIMITATION * For structural construction * At completely enclosed space * On frosty or wet target surfaces * For the parts with potential continuous flooding * In the internal fire area * For materials where oil, plasticizer, or other solvent is leaking. * For polypropylene, polyethylene, polycarbonate, or Teflon material. * At horizontal : joints potential physical friction * For the parts requiring painting on the sealant * For materials with surface temperature over 50â?? PACKING 300ml Cartridge COLOR White and grey STORAGE Shelf life is 1 year if stored unpacked in cool and dry condition away from direct sunlight.
Automatic nut tapping machine, nut tapping machine, tapping machine Hnt is suitable for hexagon, square, flange and nylon nut. Hnt can reach longer tapping stroke requirement while tapping longer or harder nuts. The operation panel is easy to understand and each spindle can be operated independent. Right or left tapping can be selected, tap life setting and adjust the tapping distance all can set up on the operation panel. Programmable language controller (plc) is used in the machine to monitor and control all tapping actions which can carry some functions including each spindle output counter is independent, operating automatically or manually, adjustable tapping speed, tapping error alarm of each spindle and motor overload alarm. Examination by current meter can detect tapping abnormal, jammed nuts during feeding or empty tapping, which can avoid tools get damage. The replacement of tools is simple and saving time. Magnetic chip filter maintain tapping oil is clean away the chips. Hnt is designed for safety consideration and qualified by ce. Hexagon thin castle nuts: din 937, 979 Hexagon thin nuts: din 439, 936 Hexagon nuts: din 555, 934, 971, 2510, 6915 Lock nuts: din 980, 982, 985, 6924, 6925, 6926, 6927 Square weld nuts: din 928, 929 Square nuts: din 557 Square thin nuts: din 562 Hexagon castle nuts: din 935 Hexagon nuts with flange: din 6923
Diesel en590 10ppm, jet fuel a1, gasoline 95 octanes.
Diesel en590 and other petroleum products.
Copper cathodes, aluminium ingots, frozen meat, frozen poultry, coal, gas oil, lng.Purchaser, distributor, importer/exporter
Foundry materials, lubricating oil.
Therapeutic grade essential oils.
Bitumen.
Robusta Green Coffee Beans.
