Description CS-613FD is a water-based multi-purposed epoxy putty and adhesive. It is developed for filling seam, gap between Calcium Silicate board. It is environmentally friendly which does not pose health hazard to user and dwellers. The best part is how easy it can be cleaned with just water. It is easy to mix even by hand due to our innovative water-based technology. Features Paintable easily with wb coating Easy to use Smooth to tool with trowel Non-sagging Stronger adhesion High solid by volume; 100% water resistant when cured. Low odor VOC free / Solvent free Uses Gypsum boardCalcium silicate board Fiber cement board Plywood / Timber Concrete / Tile It may be suitable to use on other substrates not mentioned above. Application 1. The surface to be adhered must be free of dust, release agent, oil and grease 2. Mix part A and part B with 1: 1 (by volume), and stir until homogeneous as indicated by uniform color. 3. Do not stir or mix the two parts on the application surface.
CC-402 is a one component, plasto-elastic coating based on UV-curing acrylic dispersion with excellent crack-bridging properties even at temperatures below 0°C. CC-402 complies with the requirements of EN 1504-2 as protective coating. CC-402 is used for protection and enhancement of concrete structures (normal and lightweight concrete),especially exposed outdoor concrete surfaces with a risk of cracking CC-402 is used with concrete repair works as an elastic protective coating on AFTEK smoothing mortar (refer to product / system data sheet), fiber cement and over coating of existing soundly adhering coatings. Suitable for protection against ingress (Principle 1, method 1.3 of EN 1504-9) Suitable for moisture control (Principle 2, method 2.3 of EN 1504-9) Suitable for increasing the resistivity (Principle 8, method 8.3 of EN 1504-9) Crack-bridging even at low temperatures (-5°C) High diffusion resistance against CO2 reducing the rate of carbonation Water vapour permeable Very good resistance against weathering and ageing Environmentally friendly (solvent free) .Reduced tendency to dirt pick up and contamination.
Description CA-003W Waterproof Agent is a high-grade liquid additive that gives the dual benefits of providing significant improvement in workability along with reduced water absorption. The addition of CA-003W to a mortar mixture enhances the plasticity of the mixture by creating a â??ball-bearingâ?? effect. At the same time, the microscopic capillaries are rendered discontinuous, thereby impeding the flow of liquid through them, and finally reducing the permeability of the mortar. CA-003W contains special polymers that reduce formation of shrinkage cracks. The improved cohesion provides lower rebound loss supplemented by a greater coverage. The increase in coverage can be up to 20 %. This makes significant cement savings possible. The spreading and smoothening is also made much easier. The efficiency of labor is increased, and plastering can be done in a single operation. CA-003W provides the mortar with efficient,reliable and durable damp proofing against acute rains, ground water moisture as well as environmental humidity. Thus the use of CA-003W provides significant benefits, while keeping plastering economical.
DESCRIPTION AFTEK PU 25 is a one component polyurethane based elastomeric sealant which cures under the effect of atmospheric humidity to form a tough and flexible seal joint with excellent movement performance. AFTEK PU25 performs excellent adhesion on most building materials with proven weather resistance against UV, Ozone etc. APPLICATIONS Precast façade unit sealing Light weight cladding panel Construction expansion joint Window, door flame perimeter joint Natural stone joint sealing Ceramic joint sealing Various building material joint sealing, ie. fiber glass, rigid plastic, etc FEATURES One component, ready to use High movement accommodation +/- 25% Can be over paint Non toxic, sag, staining One component ready to use Excellent weather resistance Prime less for most substrates
Flexible Multi-Purpose Hybrid Polymer Sealant Description AFTEK FLEX-PRO MS is a one-component sealant based on silane modified polymer, which is moisture cured sealant. Humidity and temperature can influence on the skin formation and curing speed, and the joint depth can also influence on the curing time. AFTEK FLEX-PRO MS is free of solvents, isocyanates,silicones and PVC. It has very low VOC while curing. It performs good adhesion to most substrates; It is suitable for most of common construction materials,especially to concrete, aluminum, mason, glass, etc. and it is compatible with most of paint systems. It has very good UV resistance property that can be used for interior and exterior applications.
DESCRIPTION * Environmental friendly water-based paints,safe and non-toxic. * Suitable for indoor/outdoor excel wall. * High performance waterproofing application, excellent permeability, and corrosion resisting. * Resist to mold,weather and chemical resistance. * Fast drying and no irritating smell, Expoy is substituted by CC105. * Apply in multiple layers with smooth surfaces. APPLICATIONS * Floor or excel wall fixing on Parking Lot,Mall,and home used. * Industrial factory and white room. * Excellent permeability and enhanced water resistance, Can be used in wet and fouling protection areas. * Used as waterproofing coating and burnish surface coating. PACKING AND STORAGES * 20 kg/pail * The amount of raw 0.1~0.15 kg/m2 (twice usage) * keep the storage environment well ventilated area. Less than 25 degrees can be stored for 6 months.
Feature : Stretchy, lightweight and easy do-it-yourself installation on any smooth surface, especially suitable childrens room, living room, bedroom, kindergartentc. Non-toxic : free of phas, heavy metals, smell free. Waterproof, anti-collision, noise reduction, antibacterial, heat insulation. It can be removed without any damage also saving your time and money instead of smelly painting. Easy to clean and maintain with damp cloth. Specification : Dimension : 60cm(l)*30cm(w)*1.3cm Color : white / grey / black / brown / wood pattern Each wall sticker attached 3 piece double-side tapes / self-adhesive Material : pe foam Application : indoors any smooth surface Customization : available Origin : made in taiwan
Description PU-850 is a one component, thixotropic, polyurethane waterproofing membrane where viscosity of the liquid is paramount. In applications such as sloped roofing, flashing details and under tile waterproofing PU 850 cures to form a durable yet elastic membrane with strong adhesion to many types of substrates. PU 850 is fast curing, and is tack-free in less than two hours, with exceptional elasticity. Due to it thixotropic, hydrophobic and elastomeric nature, PU 850 is the perfect solution to provide excellent waterproofing on vertical and sloped surfaces without running. Use - Shower Recesses - Bathrooms - Laundries - Kitchens - Balconies - Retaining Walls - Planter boxes - Steel (suitably primed) - Patios - Plasterboard - Courtyard Areas - Brick - Concrete, Cement render, plaster - Wet area wall lining board - Hardie/CSR sheet flooring - Light weight aggregate block Feature â?¢ Easily applied onto vertical and sloped surfaces with no running OR bubbling. â?¢ Excellent adhesion to most substrates. â?¢ No thinning required. â?¢ Excellent thermal resistance, never turning soft. â?¢ Excellent cold resistance, remaining elastic to -40â?°c â?¢ No accumulation of humidity under coating â?¢ Excellent mechanical properties â?¢ Highly stable, will not bleed through porous materials â?¢ Bitumen free â?¢ Highly elastic and stable. Packaging 15 Litre pail Consumption 1.2~1.5kg/m�² Shelf Life Unopened pails can be stored for up to 12 months in a cool, dry and weatherproof environment.
DESCRIPTION CP-311T elastic polyester is a new type product with a special polymerization. It is a one compound high-performance elastic waterproof membrane. The single-liquid self-crosslinking waterproof polymer with anti-fouling and wear-resisting properties is used for the coating and protection of elastic waterproof materials, roofing, wall and other elastic materials. This product has high adhesion, elasticity, wear resistance and protection. It is water-resistant, weather-resistant and hydrophobic. It is the best choice for long-term protection. SPECIFICATIONS 1. AppearanceWhite Emulsion 2. Solid Content48~52 % 3. Viscosity3000 ~ 6000 cps(RVT#3@25) 4. Proportion1.15~1.25 PROPERTIES Developed with an environmentally friendly formulation that is water-based, non-toxic and low-odor, in line with environmentally friendly low VOC regulations and CNS waterproofing specifications. The self-crosslinking single-liquid resin can make the construction work simple, and can be directly sprayed, rolled or brushed. Suitable for indoor, outdoor, floor and wall applications with high toughness, water resistance and wear resistance Excellent film properties: elastic value and stretchability, and excellent wear resistance Weathering, aging resistance, can effectively increase the life of the paint Excellent adhesion, breathability and foam resistance, which can effectively prevent surface blistering and false after application.
DESCRIPTION CC-102 Concrete Hardener is a clear high performance waterborne liquid which being applied to the floor and absorbed into the concrete pores and reacts with the calcium salts effectively making the concrete surface denser and considerably less porous. APPLICATIONS Suitable for improving the quality of concrete floors in factories, warehouse and any other area where hard non-dusting floors are important. SURFACE PREPARATION Surfaces should not have had previous treatments. They should be firm and free from oil, dirt, dust etc. Weak spots should be cut out and filled with CEMCRETEâ??S FLOOR PATCHING. All surfaces to be dry at time of application. MIXING AND APPLICATION Shake or roll drum to thoroughly mix contents. Apply HARDENER to the dry surface using a soft household broom or paint roller. Application should be liberal but it is advisable to brush away unabsorbed pools immediately to avoid the HARDENER forming glassy layers. Allow one day between coats. Two coats are usually sufficient, but a third might be required if the concrete is very porous SPECIMEN FINISH A trial area should be treated on site for the Engineerâ??s or Architectâ??s approval. COVERAGE Depends upon the suction and texture of the surface. Approximately 6m2 / litre/coat.
Description CS-613 is a multipurpose water-based epoxy sealer/putty/adhesive. Itâ??s developed for filling seam, gap between Calcium Silicate board. It is environmentally friendly which does not pose health hazard to user and dwellers. The best part is how easy it can be cleaned with just water. Itâ??s easy to mix even by hand due to our innovative water-based technology. Features / Benefits *Paintable easily with water-based coating; can be painted after 1 day without work delay hence reduce time and save money. * Easy to use: Compatible with damp surface, time is saved in waiting for it to dry up; Washable with water including tools. Best to wash as soon as possible before it hardens. * Smooth to tool with trowel; Non-sagging characteristic making it easy to use on vertical wall and ceiling. * Stronger adhesion due to higher amount of binders used. * High solid by volume; 100% water resistant when cured. * Low odor/ solvent free/ VOC free, it does not pose health hazard to user and dwellers.
DESCRIPTION ITSEAL is truly developed for sealing window frames with highly durable and flexible properties to withstand severe weathering and extreme temperatures. It seals small gap that normal sealant cannot reach and penetrate. It provides a truly watertight seal deep into minute joint and gap. FEATURES * ITSEAL is the only waterproof sealer that is completely watertight. * It is highly water repellent that no water can get through it during storm. * It adheres well on aluminum and glass * Once dried, ITSEAL is flexible and accommodate joint movement due to vibration. * Mill finish aluminum, oil or wet surfaces can also be well-sealed. VOC CONTENT Type of Regulated Adhesive under the Air Pollution Control (Volatile Organic Compounds) Regulation of Hong Kong: Architectural Sealant VOC Content (Ready to use): 248g/Ltr. SURFACE PREPARATION For maximum adhesion, the adhesive surface must be free of dust, release agent, oil and grease. Wipe surface with solvent is recommended. Solvent are obtainable from ITLS-SB. This information in this catalogue is provided to the best of our knowledge from results gathered both internal and external credited laboratories. However, we have no control over site applications, site conditions and workmanship of the applicator. We therefore will not accept any liability, either directly or indirectly arising from the misuse of these products or when the product is used not in accordance with any advice, specification, and recommendation of information given by us, The user is responsible for checking the suitability of these products for its intended use. APPLICATION ITSEAL can be used with hand operated or air operated grease pump. Other simple extruding device can also be used but it has to be solvent resistance. LIMITATION * Not suitable large gap wider than 5 mm wide and deep. For deeper joint fill to half of it, let it dry overnight and fill it up the next day. * Not suitable for use as expansion joint. COLOUR AND PACKING 26 kg / pail Grey/Black/Bronze/White SAFETY INFORMATION * ITSEAL is flammable. Please keep away from sources of ignition during application. * Avoid breathing in solvent by wearing solvent vapor respiratory mask in badly ventilated area or confined space. * Avoid contact with skin and eyes. If swallowed please contact doctor immediately. * ITSEAL meets the requirement of RoHS regulation of European Union and it does not contain eight heavy metals which were restricted by ASTM F963 or EN71 part3. * Please read the Material Safety Data Sheet in regards to flammability and health and hazard. SHIPPING/STORAGE INFORMATION ITSEAL must be stored in a cool place under 25°C and away from direct sunlight. The shelve life is 12 months if stored in accordance to the recommendation. Dangerous Goods Information: Cement Adhesive, Class 3, UN1133 PG III.
DESCRIPTION ITLS PMS 60 is a single component elastomeric sealant without isocyanates. It cures rapidly under the effect of atmospheric humidity to form a flexible and resistant joint with very good adhesion on most materials. APPLICATION ITLS PMS 60 is suitable for industrial and refrigerated trailers, truck bodies, shipbuilding, air conditioning and ventilation units, sandwich panels and other industrial applications. ITLS PMS 60 can also be used for bonding and caulking different materials used in the building industry : concrete, wood, aluminum, most lacquered metals, polyester, glass, stone, ceramic, and so on. However, for difficult materials especially lacquered or non-ferrous metals, it is necessary to make tests beforehand. INSTRUCTIONS FOR USE SUBSTRATE PREPARATION: The substrates must be clean, even, dry, free of dust, oil, grease and any contaminants that could harm bonding. All traces of poorly adherent paints or coatings should be systematically removed beforehand. They may be cleaned with PMS primer, methylethylketone (MEK) or acetone. Check the compatibility of the solvent used with the substrates. It may be necessary to rub down the substrate beforehand. After rubbing down, the surface should be recleaned. Allow the substrate to dry after degreasing. When using solvents, extinguish all sources of ignition and carefully follow the safety and handling instructions given by the manufacturer. CAULKING: ITLS PMS 60 can be applied by a manual or pneumatic gun. After application, use a putty knife to smooth the joint with soapy water. Do not apply at a temperature under 5 C. In cold weather, store the cartridges at about 20 �°C before use. This product should be used within 24 hours of opening the cartridge protection; otherwise, the sealant could harden inside. Avoid any contact with non-cured polyurethanes during curing. CLEANING: Tools can be cleaned with PMS primer, MEK or acetone before the sealant has completely cured. After curing, abrasion is necessary. STORAGE AND SHELF LIFE 12 months in the original, hermetically sealed packagings between 5 and 25 C PACKAGING 290 mL cartridges and 600 ml sausages SAFETY Not classified as hazardous. Read the material safety data sheet before use.
DESCRIPTION CC-200 is a indoor, high fluidity, rapid strength and leveling material. It still has high bonding,low shrinkage, low water absorption, acid resistance, alkyl resistance and chemical resistance. It special use for fast repairing, putty and leveling for epoxy coating. APPLICATION Floor fixing on parking garage, factory, and warehouse. Leveling before epoxy coating. Basic layer for non natural paint. Bec ause of the early strength and low moisture content, CC 200 has widely application. Contact out agent when you have doubt on CC 200. ADVANTAGES 1. Curing and enhancing are fast and rapid below 25 mins. High strength and low water absorption/ content could be reached after curing. 2. Good acid and alkyl resistance. 3. Good wear resistance, high compressive strength, leveling and anti cracking. PREPARE TO USE 1. Clean with vacuum to ensure the surface dustless. 2. Working site is free from dust, sand, oil, and loose. a). Crack and Joint Treatment b). File on the crack, open a width of 2 3 cm depth of 1 cm or more groove joints and clean up dust and loose. c). At the same time taking CC 200 mortar, filled in and up the crack and sizing 1 2 times primer after 2 4 hours. 4. Shorter wor king hours to achieve saving time, fast leveling and convenience work.
DESCRIPION FR-48 is solvent-less moisture cure type, single-component flame retardant RTV silicone product. It is suggested for use in applications requiring neutral cure, fast cure and excellent adhesion. FEATURES * Sealing of electrical components * Industrial plastic sealing, electrical insulation properties. * Low flammability â?? has a UL rating of V-0(1) * Primerless adhesion to plastics and metals * Excellent resistance to moisture, dust, UV and ozone. * Fast room temperature curing * High temperature resistance (Flexible from -60â?? to 200â?? continuous operation and 260â?? for short periods) COMPATIBILITY FR-48 contamination -free silicone sealant shows excellent adhesion for Al panel, stone, glass, PVC, or wood. As new construction materials appear and the material surface treatment method varies, some materials may cause poor adhesion or discoloration. FR-48 contamination-free silicone sealant is chemically stabilized, maintains a uniform paste shape all the time, and may be workable at the temperature range of -25â??~50â?? unless there is moisture. LIMITATION * For structural construction * At completely enclosed space * On frosty or wet target surfaces * For the parts with potential continuous flooding * In the internal fire area * For materials where oil, plasticizer, or other solvent is leaking. * For polypropylene, polyethylene, polycarbonate, or Teflon material. * At horizontal : joints potential physical friction * For the parts requiring painting on the sealant * For materials with surface temperature over 50â?? PACKING 300ml Cartridge COLOR White and grey STORAGE Shelf life is 1 year if stored unpacked in cool and dry condition away from direct sunlight.
Peelable Coating.
Ito coated glass, metal coating, ito coating.
T bars ceiling grid, ceiling tiles (calcium silicate ceiling tiles, gypsum ceiling tiles, mineral fiber ceiling tiles, metal ceiling tiles), partition frame, partition boards (calcium silicate boards & fiber cement boards, gypsum boards), fiberglass wool insulation / rock wool insulation, all purpose joint compound/ skim coat compound, flooring series (spc, wpc etc.).
Hand tools, vehicle repair tools, garden tools, measuring tool, mounted stone, pneumatic tool, thermal insulation coatings, pet accessories..
