Glass beads 0.6mm 0.8mm 1mm 1.2mm 2mm weighted blanket stuffing filling media Product Description Glass beads are made of broken glass, flat glass and other raw materials by high temperature melting bead processing. Low thermal conductivity, high strength, good chemical stability, and the texture of glass beads themselves, glass beads instead of plastic raw materials are widely used in filling, such as gravity blanket filling, compression filling, medical filling, weighted blanket filling, toy filling and so on.
Blanket all kinds of size and weight
New Technology for Sleep -Enjoy high-quality sleep with the help of technology. Safety Material - Our hypoallergenic blankets use soft, skin-friendly, and breathable 100% natural fabric as the outermost layer in close contact with the skin. Our glass beads are safe, non-toxic, and environmentally friendly. Fine Craftsmanship - Advanced processes upgraded the stitched squares to smaller and denser pockets, glass beads evenly distributed inside create a unified distribution of weight instead of sinking to the side/corner. Delicate stitching prevents glass beads from leaking through the seam.
SizeMagikTM-LP4 - LOW PICK UP ONE-SHOT PRODUCT DESCRIPTION An unique copolymer sizing agent for cotton compact yarn. Special product for air jet loom. Heavy fabric constructions are easier to weave at low-size add-ons using SizeMagik-LP4. The low add-on also permits greater protection on high-speed looms expensive reeds and sensitive mechanical parts life. SPECIFICATIONS 1. Appearance: Off white Granules 2. Solubility: Soluble at 800C 3. Viscosity of 4% solution: 10 to 30 cPs (Brookfield viscometer LVDV II+ pro -Spl.2 , rpm:100 @ 80oc) 4. Ash content (w/w) : Max 3% 5. Bulk density (gm/ml) : 0.65 to 0.85 COOKING METHOD 1. Fill the required quantity of water in the cooker. 2. Gradually sprinkle SizeMagikTM-LP4. 3. Add the required quantity of softener. 4. Close the pressure cooker lid. 5. Open the steam value and cook to @ 120�¯�¿�½?�?�ºC or 35psi. 6. Retain in the cooker for 15 to 20 minutes. 7. Then transfer the size mix to storage. ECONIMICAL ADVANTAGES Yarn abrasion resistance is an important factor affecting weave ability. The friction between the warp to warp and warp to the weft is important in determining the weaving quality. Another important abrasion point in the loom is mechanical parts (Reed, Dropper pin, Heald wire, Weft picking element). Compare with other conventional size mixes and one-shot size products SizeMagik-LP4 gives better abrasion resistance strength. DE-SIZING Easily de-sizable product with hot alkali treatment. STORAGE Keep away from direct sunlight and store in a cool, dry, and well-ventilated place. STABILITY Stable for one year from the date of manufacture. PACKING Available in 50Kg net weight PP bags with moisture-proof liner inside.
Discover our lightweight dohars which are a perfect alternative to throws and light blankets . Crafted by artisans, these stylish pieces provide elegance and comfort due to their exceptional breathability. Made typically from soft cotton, these light weight blankets allow air circulation while providing warmth, making them ideal for year-round use in any bedroom or living space. They are crafted from natural, organic cotton along with non-toxic dyes and are handcrafted using traditional techniques, thus making it an excellent choice for conscious and sustainable living.
Food stuffing mixing machine, Meat process machine Mix dumpling, steamed stuffed bun and sausage fillings,delicious food .Sanitary working ,high efficient,save labour cost .Easy cleaning ,stiring evenly ! Capacity 70kg ,150kg ,300kg, 500kg, 800kg ,and so on . welcome order !
Stick ice lollipop ice filling sealing machine The automatic stick ice filling -sealing machine for lollipop ice is small in size and light in weight, and is made of stainless steel. This machine can produce various beverages such as lollipop ice, milk sticks, fruit milk, fruit cold drinks, and so on. from small capacity to big capacity . Product parameters of one : Voltage: 220/50 (V/Hz) Power: 0.75KW Sealing speed: 2000 cups/hour Filling capacity 0-150ml Specification: 960 * 430 * 330mm (Welcome give thumbs-up, comment,transmit) welcome order !
This cake making machine can achieve fixed point filling and mobile filling according to different containers and sizes, and can produce cupcakes, model cakes, puff cakes, and Qifeng cakes. capacity 90-180pcs/min ,cake weight 20-500g/pcs . Also can design the Cake Production Line with bakery oven ---Print parttern or logo for client customized .
meatball process line / machine meatball shape machine,meatball production line The meatball forming machine adopts continuous output meatball system, which has high production efficiency, and is equipped with knives and shapers of different caliber, which can be replaced at will according to the requirements of users. The machine is mainly used to produce chicken balls, fish balls, shrimp balls, pork balls, beef balls, mutton balls, donkey balls, vegetable balls, seafood balls and other products. The main equipment of meatball production line includes meat planer, mincing machine, chopping and mixing machine, stuffing mixing machine, meatball machine, forming water tank, frying production equipment, etc. The machine is small in size, light in weight, low in noise, beautiful and generous, durable, easy to operate and maintain, efficient and energy-saving. The meat (FISH) balls produced are of good quality, smooth appearance, good roundness and uniform size. The frame body is made of 3mm thick stainless steel by bending and welding, which is solid for internal use. Wear resistant brass is used inside and outside the outlet. capacity 50-420pcs/min ,voltage 380V/50Hz .
Variable frequency regulation meatball forming machine /meatball process line / machine meatball shape machine,meatball production line The meatball forming machine adopts continuous output meatball system, which has high production efficiency, and is equipped with knives and shapers of different caliber, which can be replaced at will according to the requirements of users. The machine is mainly used to produce chicken balls, fish balls, shrimp balls, pork balls, beef balls, mutton balls, donkey balls, vegetable balls, seafood balls and other products. The main equipment of meatball production line includes meat planer, mincing machine, chopping and mixing machine, stuffing mixing machine, meatball machine, forming water tank, frying production equipment, etc. The machine is small in size, light in weight, low in noise, beautiful and generous, durable, easy to operate and maintain, efficient and energy-saving. The meat (FISH) balls produced are of good quality, smooth appearance, good roundness and uniform size. The frame body is made of 3mm thick stainless steel by bending and welding, which is solid for internal use. Wear resistant brass is used inside and outside the outlet. capacity 50-420pcs/min ,voltage 380V/50Hz .
meatball making machine meatball forming machine meatball process line/production line with frequency control and no-frequency control . The meatball forming machine adopts continuous output meatball system, which has high production efficiency, and is equipped with knives and shapers of different caliber, which can be replaced at will according to the requirements of users. The machine is mainly used to produce chicken balls, fish balls, shrimp balls, pork balls, beef balls, mutton balls, donkey balls, vegetable balls, seafood balls and other products. The main equipment of meatball production line includes meat planer, mincing machine, chopping and mixing machine, stuffing mixing machine, meatball machine, forming water tank, frying production equipment, etc. The machine is small in size, light in weight, low in noise, beautiful and generous, durable, easy to operate and maintain, efficient and energy-saving. The meat (FISH) balls produced are of good quality, smooth appearance, good roundness and uniform size. The frame body is made of 3mm thick stainless steel by bending and welding, which is solid for internal use. Wear resistant brass is used inside and outside the outlet. Capacity 50-500pcs/min ,meatball diameters : 16-40mm, above 40mm big size meatball can customized mould .
Factory Automatic Hot Eye Onion peeling process machine,from small capacity to big capacity Onion peeling process: the onion is manually fed into the hopper --- the conveyor belt automatically feeds the onion into the peeling box for peeling --- after peeling, the onion goes into the peeling roller. Under the action of high-pressure air at the side, the first and second layers of the onion are peeled off and sent out to complete the whole processing process. Features: 1. Advanced technology, reasonable mechanism, beautiful appearance, safe and reliable use, all stainless steel. 2. Automatic peeling without damage. 3. The depth of peeling is even. 4. The feeding belt is used for automatic feeding, which is simple in design and convenient in use. 5. Less peeling, high recovery rate of finished products, and over 98% of finished products. 6. Mechanical processing eliminates the hidden danger of manual processing of infectious diseases and unsanitary products. Parameters 1.process arrange diameter of round shape onion 30-150mm. 2.capacity 1000-1500kg/h 3.Power 3kw 4.Voltage 380V 5.Air Compressor :flow 1.5m2/min, pressure 0.7MPa ,power 11kw 6.Machine size 1.5*1.3*1.4m 7.Weight 420kg Start working flowing: 1.Fill onion in the loading box 2.Start the pneumatic valve switch 3.Start the power-supply switch 4.According to onion drying or fresh to adjust loading speed button/air pressure ,in order to ensure the clean degree of removing onion skin 5.When finished adjusting ,The equipment operates normally and automatically.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
TECHNICAL DATASHEET EcoTexTM -SL55 - PVA FREE ONE-SHOT PRODUCT DESCRIPTION Powder types unique one-shot product which needs no extra native starch, modified starch, binder, softener, lubricant to be added further. It is mainly used for Shuttle-less loom woven warp yarns counting above the 40s to 60�¢??s Cotton. Products are made from grafted starch, anionic polymers, and synthetic fatty matters. It contains a maximum of 13% moisture and an optimized viscosity level. Easily disperse in cold water with little swelling property due to high binding property. SPECIFICATIONS 1.Appearance - Off white powder 2.pH value of 7% solution - 5 to 7 3.Solubility - Partially soluble in cold water 4.Viscosity of size mix - 4 to 5 sec (SITRA -6mm cup) 5.Total Moisture - Max 13% 6.Bulk density - 0.5 to 0.6 g/ml 7.Total ash - Max4% COOKING METHOD 1. Fill the required quantity of water in a cooker 2. Gradually add EcoTexTM-SL55 and min for 2 min. 3. Close the pressure cooker lid. 4. Open the steam value and cook to @ 120�? �ºC or 35psi. 5. Retain in the cooker for 15 to 20 minutes. 6. Then transfer the size mix to storage. PROPERTIES 1. Moisture regain: The formation of thin flexible film absorbs water molecules from atmospheric air that maintains the required moisture content of the sized yarn. This property improves the weaving efficiency by reducing the warp stops. 2. Film property: The very thin strong film gives the inter fiber penetration that improves yarn tensile strength. Optimum elongation and flexible property significantly reduce warp break by overcoming the applied tension during weaving. 3. Abrasion resistance: The strong film withstands the mechanical friction between yarn to yarn and yarn to machine parts like reed, dropper pin, heald wire, weft picking element. DE-SIZING Easily de-sizable product with hot alkali treatment. STORAGE Keep away from direct sunlight and store in a cool, dry, and well-ventilated place. STABILITY Stable for one year from the date of manufacture. PACKING Available in 25Kg net weight PP bags with moisture-proof liner inside
EcoTexTM-SL20 - PVA FREE ONE-SHOT PRODUCT DESCRIPTION New generation eco-friendly one-shot product for a high-speed shuttleless loom. It is mainly used for 6 to 203 cotton yarns sizing. This product is entirely biodegradable and ecological. Products are made from grafted starch, anionic polymers, and synthetic fatty matters. It contains a maximum of 13% moisture and an optimized viscosity level. Easily disperse in cold water with little swelling property due to high binding property. Having high penetration power and plasticizing power for heavy construction fabrics weaving. SPECIFICATIONS 1.Appearance - Off white powder 2.pH value of 5% solution - 6 to 8 3.Solubility - Partially soluble in cold water 4.Viscosity of size mix - 5 to 6 sec (SITRA -6mm cup) 5.Total Moisture - Max 13% 6.Bulk density - 0.5 to 0.6 g/ml 7.Total ash - Max4% COOKING METHOD 1. Fill the required quantity of water in the cooker. 2. Gradually add EcoTexTM-SL20 and mix for 2 min. 3. Add other ingredients and mix for 2 min. 4. Close the pressure cooker lid. 5. Open the steam value and cook to @ 120�? �ºC or 35psi. 6. Retain in the cooker for 15 to 20 minutes. 7. Then transfer the size mix to storage. PROPERTIES 1. Moisture regain: The formation of thin flexible film absorbs water molecules from atmospheric air that maintains the required moisture content of the sized yarn. This property improves the weaving efficiency by reducing the warp stops. 2. Film property: The very thin strong film gives the inter fibre penetration that improves yarn tensile strength. Optimum elongation and flexible property significantly reduce warp break by overcoming the applied tension during weaving. 3. Abrasion resistance: A strong film withstands the mechanical friction between yarn to yarn and yarn to machine parts like reed, dropper pin, heald wire, and weft picking element. DE-SIZING Easily de-sizable product with hot alkali treatment. STORAGE Keep away from direct sunlight and store in a cool, dry, and well-ventilated place. STABILITY Stable for one year from the date of manufacture. PACKING Available in 50Kg net weight PP bags with moisture-proof liner inside.
ITO GLOBAL, SURAT, GUJARAT ( India ) We can supply high strength, quality tested and recyclable fresh PP VOVEN bags of size 29x43 inch , for filling grains (like wheat) up to 25-50-100 kgs with UV protection, BAGS Weight- as per customers requirements. as a replacement for costly Jute Bags, in packaging of 500 bags/bale with compressed packaging to save logistics costs. Size can be customized as per requirement. Also, available in transparent, milky white and colors. Bag Specification 1. Bag Size 29 x 43 inch ( 74 cm x 110 cm) 2. Bag weight 155 grams / PC (2% tolerance) 3. Mesh 11 x 11 4. UV rays protection 5. Flexible bag 6. Packaged in moisture proof and compressed bales of 500 Bag Pieces / bale 7. Estimated rates as mentioned. 8. Rates are for FOB, CIF, CFR Basis, Hazira, India. We can supply across any major port on CIF basis. 9. Samples are available.
ITO GLOBAL, SURAT, GUJARAT ( India ) We can supply high strength, quality tested and recyclable fresh PP bags of size 29x43 inch , for filling grains (like wheat) up to 25-50-100 kgs with UV protection, BAGS Weight- as per customers requirements. as a replacement for costly Jute Bags, in packaging of 500 bags/bale with compressed packaging to save logistics costs. Size can be customized as per requirement. Also, available in transparent, milky white and colors. Bag Specification 1. Bag Size 29 x 43 inch ( 74 cm x 110 cm) 2. Bag weight 155 grams / PC (2% tolerance) 3. Mesh 11 x 11 4. UV rays protection 5. Flexible bag 6. Packaged in moisture proof and compressed bales of 500 Bag Pieces / bale 7. Estimated rates as mentioned. 8. Rates are for FOB, CIF, CFR Basis, Hazira, India. We can supply across any major port on CIF basis. 9. Samples are available.
LLDPE Reprocessed Transparent Color For Sales MATERIAL : LLDPE reprocessed transparent color CATEGORY : LLDPE TYPE : Reprocessed GRADE : Transparent color SPECIFICATION : First grade reprocessed LLDPE natural color filled in seperate bags. LLdpe - MFI 0.92 equal to virgin film grade Natural 80MT ORIGIN : New Zealand LOADING WEIGHT : 20 Tons FAS (USD/Ton) : 1000-1200
PP Fruit Crate Regrind Black Color Scrap MATERIAL : PP Fruit Crate Regrind Black Color CATEGORY : PP TYPE : Regrind GRADE : Black SPECIFICATION : Post- consumer, made from fruit crates Washed, 10% filled/ unfilled. No contamination MFI: 10-13 ORIGIN : Turkey LOADING WEIGHT : 23 Tons FOB (USD/Ton) : 500-650
