Waste Oil Suppliers and Manufacturers

Application Series COP oil recycling machine is mainly used for purifying UCO used cooking oil, vegetable oil, KFC oil, edible oil, rape oil, sesame oil, peanut oil, coconut oil, beam oil, kitchen oil, bio-diesel oil, plant oil, wood oil etc. It dewaters, deodorizes, and eliminates impurities highly effectively. According to the cooking oil nature, the used cooking oil includes high content water, more acid matters, much impurity and offensive odor. This machine adopts plate pressure system and can separate the impurities and water from the oil quickly and effectively. Added two primaries filter and fine filter, it can remove impurities thoroughly. And the machine adopts high vacuum system to dewater and deodorize. In addition, this machine uses stainless steel filter elements, which resists the acid in oil strongly. After the used cooking oil is recycled by machine, it will become clear and fresh. Features 1. Highly effective vacuum dewatering, deodorizing, and impurities removing system. 2. It adopts plate pressure system with the strong ability to filter the particles and impurities completely. 3. It has the back flush system which can clean the filter elements automatically. 4. We uses stainless steel filter element which has a good anti-corrosive performance. Especially, the precision of eliminating impurity is high and the service life is long. Also, it has large volume for holding the impurities. 5. Unique degassing and dewatering system: Using 3D-Evaporation technical and thin film evaporation, which can separate the trace water, soluble water and gases from the oil quickly by the Multi-level water-oil separation technology. 6. Hi-automatically operated, convenient, reliable, and safe.

Waste Oil Refinery Machine can be used in black engine oil, crude oil,plastic oil and shale oil, to get gasoline and diesel oil through distilled catalyst. Pumping into the heater with raw material , through the gas,fuel oil or coal heating to working temperature, the maximum working temperature about 410 degree and the required gasoline and diesel oil can be obtained after catalytic distillation. When the reaction of raw material in reactor is complete, stop heating, and remove residue from the tank of bottom, then this machine can be used again. Systems of equipment Reaction tank: raw material will be pumped into this tank from the primary filter . Heating system: by burning fuel oil ,gas or coal to make the oil temperature up to setting value. This system equips with insulation system. Catalytic system: raw material reaches the predetermined temperature, via catalytic effect, and then the gaseous hydrocarbons will become gasoline and diesel composition. Cooling system: gasoline and diesel after catalytic effect can be condensed into liquid materials. Temperature control system: ensure that raw material transform into gasoline and diesel oil, raw material drying by distillation, can stop heating timely. Exhaust gas handling system: a small amount of not liquefied gas via treated, can meet emission standards. 3.Index of oil after treatment: Yield diesel oil : 86-88%, gasoline oil: 5-6%, oil residue: 6-8%. Low-speed diesel engine can be used directly.

Application: This kind of purifier is applicable to purification of various used black engine oil from transport facilities such as ship and automobile. This machine can remove the tiny impurities dispersed in oil such as carbon particles and deep oxides, as well as bad substance such as colloid and bitumen. Thus, the clarity of oil is recovered and the color of used black engine oil is restored. Features: 1. This machine adopts physical & chemical theory to get the refined and regenerated oil. 2. with the special waste gas collecting and absorbing device, this machine can stop most of the harmful gas going into the air and be friendly to the environment. 3. The fine filtering system use fully-automatic filter press with liquid press method to remove impurities, which have big area to filter impurities and can be operated and maintained easily. 4. The advanced fully-automatic temperature controlling system, liquid-level controlling system, defoaming controlling system, pressure protecting system and excellent equipment can ensure operation of the machine with high performance. 5. Indirect heating used by the heating system to ensure waste oil to be heated evenly and the temperature of waste oil to be stable. 6. The vacuum system is used for high-level removing the micro water and the left gas of the waste oil. 7. This machine also installed phase-sequence and open-phase protection and creepage-proof protection. Technical Parameter List Name Unit ZLE-ó± ZLE-ó= ZLE-ó= ZLE-ó( Capacity Kg/D 1000-2000 2000-4000 4000-8000 8000-16000 Recovery Rate % 80-95 (or follow requirement of waste oil ) Working Pressure Mpa í_0.4ú¡0.6 Noise dB(A) í_65ú¡80 Power Supply V/Hz 380/50ú¿or at userí»s optionú¬ Whole Power KW 55 70 90 120 Weight KG 2500 3500 5000 8000 Remark The capacity is based on that the oil purifier works 8-16 hours per day. Wooden case.

Product Description: This kind centrifuge is a separator for separating solid, liquid and liquid for chemical, pharmaceutical, oil, foodstuff, milk industry, daily industry and defense industry etc.. It has three types for solid discharge such as central value deslagging, artificial deslagging, and water push deslagging. The first type is mainly used in the desoponificating of oil refining, and the last two types are used in degumming and dehydrating, they are all applicable for liquid-liquid-solid and liquid-solid separation. It has advantages of high speed, smooth operating, compact structure, small footprint, all sealed of the inlet and discharge, little noise, good separation. Application: It is widely used in chemical, pharmaceutical, oil, foodstuff, milk industry, daily industry and defense industry such as: 1. Food stuff industry: For animal protein extraction and separation, as well as in meat processing for refining animal lipid or in concentrating and separating aquatic products of fish oil, in clarifying and degreasing milk, for the clarification of beer and malt, sparkling wine, fruit juice and drinks and so on. 2. Chemical industry: Mainly used in separating industrial chemicals, paint and coatings. Also it could be used in the clarification and purification of wastewater from light, textile, chemical fiber industry as well as analogues of greater density solid-phase. Also it is used for concentrating and clarifying of natural rubber, it separates rubber milk into concentrated latex and clear pastern. At the same time it removes the solid impurities in serum. 3. Pharmaceutical Industry: Mainly used in separating biopharmaceuticals, pharmaceutical medicine, vaccines, mycelium, glucose, insulin, vitamins, antibiotics, pigments, proteins, spices and so on. 4. Oil industry: It can be used vegetable oil, animal fat, fish oil, soap oil, biodiesel and other lipid-foot, swill oil as raw material, through new centrifugal separation process of trans- esterification and access . 5. Other industry: It mainly used to remove the water and mechanical impurities contained in equipment fuel and lubricants in boating mainframe, diesel power station as well as other types of mineral oil, in order to reduce diesel engine or other mechanical wear and extend the useful life of the mechanical. Also applies to separate and clarify similar materials of waste oil in other petrochemical industries, such as black oil, delayed coking oil, washing oil and recycle oil and so on.

JZC Waste Oil Refinery Plant Application: Waste oil usually collected from machinery, vehicles, ships etc. which color is black and very dirty. Because the waste oil contains too much contamination, including non-hydrocarbon, alkene, polycyclic aromatic hydrocarbon, metal hydronium, impurities, metal particles, asphaltene and colloid etc. thereby it is harmful for the lubricating system and car engine etc, waste oil lost itâ??s control friction which have to be replaced. Transitional way to recycling the waste oil is by acid way,So our company researches the new waste oil vacuum distilling machine (JZC waste oil distillation machine), it is special for distilling and regenerating the black waste lube oil, including waste engine oil, lube oil, hydraulic oil, gear oil, dirty diesel oil, mixed oils etc. JZC waste oil distillation machine heat the waste oil to (from 110 to 350) different temperature under high vacuum condition, making Hydrocarbon molecules break out, and re-order combination, forming diesel oil, lubricating base oil etc. JZC machine is very suitable for the small oil refinery company, also for the small oil company who want to make the oil by self. Advantage: Safety design, during the working process, raw materials oil is always flowing and flashing between the distillation tank and heating system, there is no any coking happen in the pipes and tanks, so the system is 100% safety, and long life time. There are optional ways to heat the oil, like the boiler way by using fuel, natural gas or coal. Also, if machine is small capacity, we can use the electric heating way. By using the high vacuum distilling way, so the distilling temperature is low, energy saving and safety. Using the special chemicals to catalyze the waste oil, which makes sure the final diesel oil, gasoline oil and base oil are good anti-oxidation with good color, there is no bad odor. The final oil can be storage for one year without color change and odor change. Technical Parameter: Index Unit JZC-2 JZC-5 JZC -10 JZC -20 Capacity Ton / day 2 10 20 Recovery ratio % Above 85% Working pressure MPa 0.4 Working vacuum MPa -0.08 ~ -0.0998 Working Temperature 80-350 Working Noise dB (A) 75 Power supply V 380v, 50hz, 3Phase (Or According user demand) Heating way Electromagnetic-Heater or boiler ( fuel, natural gas or coal) Pump Motor Power kW 15 25 45 60 Working Size M2 200 300 500 700 Recovery rate: Final products Ratio Percentages Distillation temperature Vacuum Value Water 2% 80-110 -0.098 Gasoline and diesel 8% 120-210 500Pa Light base oil 40% 220-290 300Pa Heavy base oil (Viscosity SN150 ) 45% 300-350 200Pa Oil Residual 5% Total 100%

Raw material: waste oil, waste lube oil, waste engine oil, crude oil, pyrolysis oil, black oil and son on Final product: standard diesel oil Daily capacity: 5-10 tons per day Work pressure: Normal Warranty: 5 years Details information, welcome to send enquiry! Amanda Zhao Jiaozuo Zhongli New Energy Equipment Manufacturing Co.,Ltd.

Waste oil, used oil, sludge oil, scrap oil , gear oil, transformer oil.

We supply waste vegetable oil, POME,Mixed Fatty Acid Palm Pitch Palm Acid Oil High FFA CPO Used Cooking Oil Biodiesel Residue Fatty Matter Oil, Fatty Alcohol Residue for Power generation, Bio bunker & industrial burning. If you have any request do let us know the following, Product Packing Qty Destinatiopn Port Docs you need with your shipment

Sino-NSH-GER is regeneration system for waste engine oil including diesel engine oil, gasoline engine oil, as well as used hydraulic oil and some other machinery's lubrication oils. Sino-NSH-GER is designed with the combination technology of physical and chemical processing, can effectively remove aging products and contaminants from used oil. Physical processing method can remove solid particles, water, gas, etc. Chemical processing method allows removal of colloid, oxide, pitch in the used oil. Specially, this system can restore the color of used oil and remove the scent rapidly. Sino-NSH-GER is an environmentally friendly system, abandon traditional acid processing method, effectively solve the environmental pollution caused by the old technology of waste oil recycling. Various options are available for this system to improve the automation of operation.

The main function of Lubricating Oil Purifier is to purify the contaminated lubricating oil, motor oil, gear oil, hydraulic oil, compressor oil, turbine oil and restore its original performance, it is a professional oil filtration machine. In the purification processing the filter residue accumulation, resistance increased, flow rate slow, should stop work to cleaning residue. When Lubricating Oil Purifier removes impurity, pay special attention to filter on the stainless steel wire mesh deformation or damage, otherwise, when installed filters again, the purity of the filtered medium can not meet the design requirements, compressor, pump, instruments and other equipment will be destroyed, once found that stainless steel wire mesh deformation or damage should be replaced immediately. The filter element of Lubricating Oil Purifier is composed of special materials, is easily damaged parts, need special protection; When fine filter work after a period of time, the filter to block a load of a certain amount of impurities, the pressure will increase, flow rate will decline, need to remove the impurities in the filter system in time, at the same time to clean the filter element.

Sino-NSH-GED-WB is designed to process and recycle waste oils, thereby to acquire high quality base oil. Sino-NSH-GED-WB adopts the advanced technology of vacuum distillation, can effectively remove wearing debris, pitches, waxes, impurities, water, carbon deposits, oxide from the waste oil, as well as decrease the acid. The base oil acquired is with high quality that can meet the standards and requirements for blending various industrial lubrication oils. During the distillation process, a powerful vacuum pump system provides a stable vacuum, the hydrocarbon chain breaks to reform new molecule of the oil, and turns into oil mist. Then it turns to liquid oil by effective condensation. Exhaust gas treatment device is equipped to ensure that emissions gas strictly meets environmental requirements. Sino-NSH-GED-WB is the upgrade model of NSH-GER, saves operating costs and increase oil recovery rate, it can reach high rate above 90%. In addition, NSH-GED-WB has a wider range of applications, can be used to process almost all waste oils, such as engine oil, hydraulic oil, gear oil, etc. Both single oil or oil mixture can be processed and recycled by the system. Various capacities are available for this system to meet different needs of customers, and a variety of heating methods also allow customers to choose according to actual needs.

Waste Oil Purifier Machine\ Oil Purification System can treat a variety of waste lube oil, to get high quality base oil and a small amount of gasoline and diesel through vacuum distillation. After pretreatment, waste oil pumping into the distillation kettle, and heating to working temperature, we will can get the base oil, gasoline and diesel .When reaction completed, stop heating, remove residue from the bottom of the tank, then the machine can be used again. The production is economical, however, the base oil is excellent .This is the most advanced technology in the world in the waste oil recycling field, and it is suitable for large-scale industrial production. Systems of equipment 1 Pretreatment systemï¼?Waste oil will be pumped into the distillation kettle after pretreated. 2 Distillation system: through burning gas , fuel oil or coal to make the oil in the kettle up to the working temperature. This system equipped with stirring system and insulation system. 3 Cooling system: the gaseous hydrocarbon will be cooled into liquid base oil. Gasoline and diesel. 4 Oil storage system: the base oil, gasoline and diesel get from cooling system storage here, and then pump into the storage tank. 5 Vacuum system: meet the technology requirement. 6 Filtration system: rapidly filter out mechanical impurities in the base oil, gasoline and diesel, get the high quality base oil, gasoline and diesel. Recovery rate Base oil: 85%~88 %( index same as SN150~SN200) Gasoline: about 3% Diesel: about 3%-4% Oil residue: 6%~8%

NSH GED Vacuum Distillation System is able to regenerate a variety of waste oil: engine oil, transformer oil,motor oil, car oil, lubrication oil, gear oil, hydraulic oil, washing oil, Ship marine oil, etc. Specialized not only one single type of oil, but also mixed waste/used black dirty oil. After the distillation treatment, vacuum treatment and regeneration treatment through GED system, you can get high quality diesel, and a small amount of gasoline

We Supply Used cooking oil for Bio diesel and others as below : USED COOKING OIL SPECIFICATION Free fatty acids 3 % Max M.I.U(Moisture and Impurities) 0.1 % max Saponification value: 18185-1955-195 Iodine value: 120 Titre C (melting point) 13.75 'C Specific Gravity @ 25 C 0.915 Density (kg/m3) 920 Flashpoint by P.-M. (Degree C) 220 Calorific Value (kj/kg) 36, 000 Kinematic Viscosity (40 deg.C) (mm2/s) Carbon Residue (mass-%) 0.4 Sulphur Content (mg/kg) 16 Contamination (mg/kg) 24 Acid Value (mg KOH)/g) 7.0 Oxidation Stability (110 deg.C)(h) 5.0 (min) Phosphorus Content (mg/kg) 15 Ash Content (mass %) 0.01 Packaging & delivery TRANSPERENT PET BOTTLES * 1L, 3 L,5 Liters and in bulk PET Transparent Bottle (With Handle). JERRYCANS * 5 L, 10 L, 20 L, 25 L and 220 Liters Jerry can. METAL TIN * 16 L, 14 kg (with or without carton), 15 L / 15 kg, 16 kg (with or without carton 17 L / 17 kg, 18 L / 18 kg, 20L Metal Tin with Bung Hole (Round or Square) and 211 Liters Metal Drum. FLEXI TANK 20 MT Flexi Tank.

overview Black Waste Oil Purification Machine to SN300 can treat a variety of waste lube oil, to get high quality base oil and a small amount of gasoline and diesel through vacuum distillation. After pretreatment, waste oil pumping into the distillation kettle, and heating to working temperature, we will can get the base oil, gasoline and diesel .When reaction completed, stop heating, remove residue from the bottom of the tank, then the machine can be used again. The production is economical, however, the base oil is excellent .This is the most advanced technology in the world in the waste oil recycling field, and it is suitable for large-scale industrial production. Systems of Black Waste Oil Purification Machine 1 Pretreatment systemWaste oil will be pumped into the distillation kettle after pretreated. 2 Distillation system: through burning gas , fuel oil or coal to make the oil in the kettle up to the working temperature. This system equipped with stirring system and insulation system. 3 Cooling system: the gaseous hydrocarbon will be cooled into liquid base oil. Gasoline and diesel. 4 Oil storage system: the base oil, gasoline and diesel get from cooling system storage here, and then pump into the storage tank. 5 Vacuum system: meet the technology requirement. 6 Filtration system: rapidly filter out mechanical impurities in the base oil, gasoline and diesel, get the high quality base oil, gasoline and diesel. Recovery rate Base oil: 85%~88 %( index same as SN150~SN200) Gasoline: about 3% Diesel: about 3%-4% Oil residue: 6%~8%

Model:HH24-60 Size:2.4*6.0m Heating area():45.22 Volume(m3):27.13 Chain weight plastics(t):16.3 Tire weight(t):6.78 Segmentation tire weight(t):10.85. No

We can offer waste tyres & waste oil Bulk

ITEM STANDARD Free fatty acids 3 % Max M.I.U(Moisture and Impurities) 0.1 % max Saponification value: 18185-1955-195 Iodine value: 120 Titre C (melting point) 13.75 'C Specific Gravity @ 25'C 0.915 Density (kg/m3) 920 Flashpoint by P.-M. (Degree C) 220 Calorific Value (kj/kg) 36,000 Kinematic Viscosity (40 deg.C) (mm2/s) Carbon Residue (mass-%) 0.4 Sulphur Content (mg/kg) 18 Contamination (mg/kg) 24 Acid Value (mg KOH)/g) 7.0 Oxidation Stability (110 deg.C)(h) 5.0 (min) Phosphorus Content (mg/kg) 15 Ash Content (mass %) 0.01

ZLA series Waste transformer oil filtration machine is manufactured according to standards, which go beyond Chinese legal criterion, dealing with almost insulation oil of power equipment more rapidly and effectively with the supporting of high vacuum and speed absorption. Thus the strength of insulation oil is much increased and shorten the dealing time. Features 1) Manufactured as per standards which go beyond the legal criterion.A primary breakdown voltage can raise 35KV and reduces the oil damage causing by normal purifiers due to repeated heating. 2) Large absorption speed double vacuum meets the needs of vacuum zing of transformer on an installation or repair site, at the same time remove the water,gas,and also keep the completeness of transformer oil.It significantly shortens the oil treatment time. 3) The unique gas, water removal system adopting stereo-evaporation technology, which rapidly separates the water and gas in the oil and is free of maintenance. 4) A superior purification system with top quality filter core, which can accommodate large quantity of impurities and is progressively dandified step by step. It has been got a high precision and multi-stage filtration. 5) Imported parts adopt all electric system, which ensures high performance. 6) Advanced infrared liquid level control system with automatic control, allowing separated operation of manual operators from a machine. 7) Interlocked safety protection device. i.e,backflow of A oil outlet over pressure can be achieved via an overflow valve, B oil inlet will interlock with heating system which avoids any possible negative impacts caused by mal-operation 8) Precision oil pumps have low noise and environmental regulatory compliance will be well met . Technical Parameters Model Unit ZLA-30 ZLA-50 ZLA-70 ZLA-100 ZLA-150 ZLA-200 ZLA-250 Rated flow L/min 30 50 70 100 150 200 250 Vacuum Range Mpa -0.05~-0.099 Temperature Range 40~80 Oil pump pressure Mpa 0.05~0.3 Total Power kw 38 46 62 90 120 144 175 Power 50HZ 380V Working Noise db(A) 65 85 Cleanliness NAS1638 NAS 6 Breakdown Voltage kv 75 Water content PPM 3 Gas content in oil % 0.05 Filter precision µm 3 Inlet (outlet) diameter 25 32 32 42 50 60 60 Dimension mm L 1480 1670 1820 2000 2100 2300 2300 W 980 1150 1300 1500 1600 1800 1800 H 950 1000 1200 1300 1600 1600 1600 Dimension and weight will be changed with changing the technical specification.