Washable Dust Picker Remover Brush Roller Suppliers and Manufacturers

Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)

- Type: Staple Set (Tufted) Roller Brooms / Brushes; - Filaments Material: PP Wire / PBT Wire / PA Wire; - Filaments Diameter: PP/ PBT / PA 1.8 ~ 3.2 mm; - Hollow Shaft Material: Plastic; - Shaft Flange: At customers requested; - Brooms Size: ID 450 ~ 900 mm; - Functions:Road / Street / Outdoor Cleaning etc.; - Compatible Vehicle: Epole / Dulevo Diesel and Electric Sweeper etc.

Household items like Brush, Mop, Broom, Gloves, Husk, Lint Roller, Sponge, Dustpan Product of Indonesia

Commodity: Calcium chloride Molecular formula CaCl2 H.S code 28272000 Product feature Calcium chloride is an inorganic salt, which exists as solid or liquid. Solid calcium chloride is a white, crystal substance in the form of flake, granule, pellet or powder. With different crystallized water contents, it can be dihydrate or anhydrous. Liquid calcium chloride is a colorless, clear solution. As calcium chloride has such properties as quick dissolving, exothermic ability, attracting moisture from the air and surroundings, dissolving at very low temperature, Specifications: Analysis Item Standard Calcium chloride (CaCl2) 74%min,77% min,94%min Total Chlorinated Alkali: (NaCl) 5.0%max Magnesium Chloride(MgCl2) 0.5%max Insoluble matter in water 0.25%max Calcium Sulfate (CaSO4): 0.2%max Ferric Oxide (Fe2O3) 0.025%max Heavy Metal as Cu., Pb., Cd., Cr., Hg., As 0.005%max Application Mainly used in drying, melting snow for airport express and street, concrete desiccant and concreting fast, removing dust and oil industry. Exporting Packing :Plastic woven bag with PE ,25kg/50kg/1000kgs net weight or 25kg x 40 bags into one big bag or 40 bags on a pallet with shrink-wrapped Means of transportation :in containers or by bulk vessel with large quantity

Coco peat brick is also known as coir pith or coir dust, it’s made from coconut husks. Coco peat primarily consists of the coir fiber pith or coir dust which is obtained by processing coconut husk and removing the long fibers. Planet Coco’s peat brick is low in EC and have very low salt content. Our Coco peat is aged and composted for over 18 months and thorough washed. Our one liter brick can be expanded up to 8 liters by adding 2 liters of water. 650 Bricks are a perfect size to handle and it’s the perfect size for home gardeners. Usage Environmentally-friendly & sustainable organic alternative to peat moss. Used in greenhouses, vertical gardens, landscaping & grow bags.

Silicone Toilet Brush with Removable Holder TPR brush head - The brush head made of TPR material does not scratch the toilet and does not absorb hair/dirt. It is easy to clean. The special material makes the brush head more durable than conventional brushes, never wear or deform. 360�° thorough cleaning - The round brush head with dense soft bristles can efficiently reach into hard-to-reach areas such as grooves, dead corners or areas under the rim and allow for thorough cleaning. No single corner remains dirty. The handle is made of PP material and is installed rotatable. It is comfortable to catch and easy to disassemble. Quick drying holder - With unique hollow ventilation, the water on the brush head would dry efficiently after cleaning. The drawer design makes it easy to pour the extra water without water leaking or smelling bad due to accumulated water in the holder. Two placement options - The brush head with square base can be placed stably on the floor on the holder. With the included adhesive hook, you can also attach the holder to the wall, keeping the floor and base of the holder dry and tidy. This is not an obstacle when cleaning the floor of the bathroom or toilet. Additional information Weight 0.85 lbs Dimensions 8 x5 x 5 in Type TRP toilet brush with rope Material PP+Aluminum+TPR Color White + Gray Size 11*45cm

Fly Ash: Fly Ash is by product generated during combustion of coal, and comprises the fine particles that rise with the flue gases. Ash which is collected from the bottom is termed bottom ash. Fly ash is collected by electrostatic precipitators or other particle filtration equipment before the flue gases reach the chimneys of coal-fired power plants and together with bottom ash removed from the bottom of the furnace is in this case jointly known as coal ash. Depending upon the type of coal being used, the specification of Fly Ash varies considerably, but Fly Ash contains substantial amounts of silicon dioxide and calcium oxide (CaO), both being endemic ingredients in many coal-bearing rock strata. We are a reputed Fly Ash Exporter based in India and are supplying Fly Ash different cement, ready mix concrete, steel, refractories and construction industries. The Major Utilization Areas Of Fly Ash : - Manufacture of Portland Pozzolanic Cement & Performance improver in Ordinary Portland cement (OPC). - Part replacement of OPC in cement concrete. - High volume Fly Ash concrete. - Roller Compacted Concrete used for dam & pavement construction. - Manufacture of ash bricks and other building products. - Construction of road embankments, structural fills, low lying area development. - As a soil amender in agriculture and wasteland development. Types of Fly Ash: - According to the type of coal used fly is classified into two types. Anthracite and bituminous coal produces Fly Ash classified as class F. Class C Fly Ash is produced by burning lignite or sub-bituminous coal. Class C Fly Ash has self-cementing properties. - Class F and Class C Fly Ash are products of the combustion of coal in large power plants. Fly Ash is collected in electrostatic precipitators or baghouses, and then transferred to large silos for shipment. When needed, Fly Ash is classified by precise particle size requirements, thus assuring a uniform, quality product. - Class F Fly Ash is available in the largest quantities. Class F is generally low in lime, usually under 15 percent, and contains a greater combination of silica, alumina and iron (greater than 70 percent) than Class C Fly Ash. - Class C Fly Ash normally comes from coals which may produce an ash with higher lime content generally more than 15 percent often as high as 30 percent. Elevated CaO may give Class C unique self-hardening characteristics. Minimum Order Quantity : 1 container

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Root vegetable /shellfish cleaning peeling machine : Root vegetable/shellfish cleaning peeling machine adopts the principle of low speed brush cleaning and high speed peeling with sand roller.This machine has the characteristics of small energy consumption,small volume ,light weight,beautiful appearance and convenient operation.The box is made of high quality stainless steel material,no corrosion,clean and hygienic ,the roller is not easy to deform,the brush is made of nylon rope rolling ,durable . Capacity 300-800kg/hour ,power 1.5-2.2kw .

Root vegetable cleaning peeling machine : Root vegetable/shellfish cleaning peeling machine adopts the principle of low speed brush cleaning and high speed peeling with sand roller.This machine has the characteristics of small energy consumption,small volume ,light weight,beautiful appearance and convenient operation.The box is made of high quality stainless steel material,no corrosion,clean and hygienic ,the roller is not easy to deform,the brush is made of nylon rope rolling ,durable . Capacity 300-800kg/hour ,power 1.5-2.2kw .

Factory Automatic Hot Eye Onion peeling process machine,from small capacity to big capacity Onion peeling process: the onion is manually fed into the hopper --- the conveyor belt automatically feeds the onion into the peeling box for peeling --- after peeling, the onion goes into the peeling roller. Under the action of high-pressure air at the side, the first and second layers of the onion are peeled off and sent out to complete the whole processing process. Features: 1. Advanced technology, reasonable mechanism, beautiful appearance, safe and reliable use, all stainless steel. 2. Automatic peeling without damage. 3. The depth of peeling is even. 4. The feeding belt is used for automatic feeding, which is simple in design and convenient in use. 5. Less peeling, high recovery rate of finished products, and over 98% of finished products. 6. Mechanical processing eliminates the hidden danger of manual processing of infectious diseases and unsanitary products. Parameters 1.process arrange diameter of round shape onion 30-150mm. 2.capacity 1000-1500kg/h 3.Power 3kw 4.Voltage 380V 5.Air Compressor :flow 1.5m2/min, pressure 0.7MPa ,power 11kw 6.Machine size 1.5*1.3*1.4m 7.Weight 420kg Start working flowing: 1.Fill onion in the loading box 2.Start the pneumatic valve switch 3.Start the power-supply switch 4.According to onion drying or fresh to adjust loading speed button/air pressure ,in order to ensure the clean degree of removing onion skin 5.When finished adjusting ,The equipment operates normally and automatically.

Natural Sisal Fiber Type 1 Type 2 Type 3 Type 4 Sisal Fiber UG Grade Length: 110CM-130CM with a tolerance of 20%. Moisture: 10%-13% Impurity: 0-3% Classification per Grade: TYPE 1 - Colour whitish/soft cream, well brushed humidity maximum 14% without knots. Color: natural white, Brown and between white and brown. TYPE 2 - Colour cream/yellowish, well brushed humidity maximum 14% without knots. TYPE 3 - Colour cream/yellowish, well brushed humidity maximum 14%, without knots. REFUGOS (REJECT) - Colour brownish/green, humidity maximum 14%, presence of knots and high percentage of impurities. BUCHA (TOW) - Colour yellowish/brownish, humidity maximum 14%, presence of knots and a very high level of dust.

Natural Sisal Fiber Type 1 Type 2 Type 3 Type 4 Sisal Fiber UG Grade Length: 110CM-130CM with a tolerance of 20%. Moisture: 10%-13% Impurity: 0-3% Classification per Grade: TYPE 1 - Colour whitish/soft cream, well brushed humidity maximum 14% without knots. Color: natural white, Brown and between white and brown. TYPE 2 - Colour cream/yellowish, well brushed humidity maximum 14% without knots. TYPE 3 - Colour cream/yellowish, well brushed humidity maximum 14%, without knots. REFUGOS (REJECT) - Colour brownish/green, humidity maximum 14%, presence of knots and high percentage of impurities. BUCHA (TOW) - Colour yellowish/brownish, humidity maximum 14%, presence of knots and a very high level of dust.

Code 82700: Moisturizes, lightens the scar, hypoallergenic Features 1. Flesh color silicone sheeting with hypoallergenic adhesive. 2. Snug-fitting, washable and reusable for more than 15 times. 3. Pain-free and easy removal. Size: 1 cm x 10 cm x 1 sheet Material: PU, silicone gel

Nitrile Gloves Nitrile Medical Examination Gloves OEM customization Medical Powder Free gloves FORM FITTING, & AMBIDEXTROUS Smooth and easy to put on, with these ambidextrous gloves you will no longer have to struggle to find the right fit. As they conform nicely around your hand and fingers they allow for great dexterity, so you can proceed with your daily tasks without the slightest discomfort. SAFE FOR PROFESSIONAL, COMMERCIAL & HOME USE Our medical exam gloves are a must-have addition to the equipment of any doctor, nurse, dentist, caregiver and vet. They are also great as kitchen gloves for cooking and food prep, cleaning, painting, pedicure, hairdressers and other beauty services, technicians, engineers, lab workers and so much more. GREAT PROTECTION WITHOUT STRAINED HANDS Wearing gloves for a prolonged period may make your hands feel numb, stiff and strained. But that's not the case with the Medpride vinyl - nitrile blend powderless gloves that are so stretchy and comfortable you won't even notice them. Plus, they have a roller cuff for easy removal.

Alfalfa Pellets Thank you for contacting us. We can offer best quality Alfalfa Pellets. Further, this is a 100% Natural Product grown and cultivated in Gujarat State of India, the nutritional specifications are subject to vary as no additions of foreign matters are made to increase/control the nutritional specification of the same. Available In : 8 x 25 mm We produce widest range of Alfalfa Pellets for Animal Feeding Objective. We produce 8� mm Alfalfa Pellet and 10� mm Alfalfa Pellet for Animal Feed Forage Industry Alfalfa Pelleting Process Generally its grown during the period of November to April Months of the year in India and the cutting process begins from the 45th� day of the plantation. The field cut green alfalfa is spread on the agriculture land for sun drying process (which is generally called sun curing process). This is the most important phase of administration, wherein during the sun curing process the alfalfa leaves and stem has to be dried in such a manner that the leaves should not turn yellow or loose green pigments. After 7 days of meticulous administration, the green alfalfa is converted in to hay. The hay is loaded in trucks and transported to production side, where the first stage is to sieve (clean) the entire hay, so minor or major dust articles are removed from the same. After cleaning process the hard stem particles are removed through a mechanical machining process and the available residue is absolutely clean and dehydrated soft leaves and soft steam. The dehydrated alfalfa particles (leaves & steam) are grinded to a finer particles size. The overall texture of hay is now converted to Powder Form. The powdered alfalfa is then passed through 100 degree Celsius stream for about 8 minutes, which detoxifies the alfalfa from any toxic elements and also gets cooked at a very digestible ratio. The highly cooked alfalfa meal is then pelleted through feed extrusion methodology, during the process of pelleting again the cooked meal reaches to an extremely high temperature of 123 Degree Celsius, due mechanical thrust of the extruder in its 22 ft long barrel The extremely hot pellets are then cooled down to a room temperature level, enabling the moisture level below 12%. The above process produces the most advance format of Alfalfa Hay Pellet in 8 x 25 mm�  and 6 x 25 mm size absolutely hygienic for Animal and Poultry feeding Purpose Facts of Indian Alfalfa The pricing of the alfalfa hay / pellet is totally dependent of the physical hay recovery after sun curing process, which varies 10% to 15%, which means when 100 Kgs of green alfalfa is sun dried, the hay recovery varies between 10Kgs to 15 Kgs. The recoveries are totally dependent on the environmental factor and the water content within the stems of the alfalfa. Countries like Canada, Northern US, New Zealand and Northern European Countries donâ??t get direct sun light (rather they get inclined sun lig