Tublar Turbine Suppliers and Manufacturers

The tubular turbine is an axial flow turbine, in a straight or S-shaped configuration. A Tubular Turbine can be supplied for a head of 2 m to 30 m. The runner diameter is available from 0.8 m to 5.6 m. Power capacity is from 250 kW to 15 MW. This turbine has high efficiency and lower constructon cost.

The Axial turbine is for low head power plants. Water flows axially into and out of the turbine. Axial flow turbines fall into two categories, fixed blade runner and variable pitch runner, also known as a Kaplan turbine. Fixed blade turbines are very well suited to low head power plants with limited variation in head and load. Its main advantage is its simple design. When operated at fixed speed, maximum efficiency is achieved at the design head and water flow. Kaplan turbines are used for medium to large power stations where there are large variations in the head, water flow and load. Its main advantage is its ability to adapt to variable conditions with a high efficiency. The variable pitch runner is mechanically more complex than a fixed pitch runner. Axial flow turbines can be supplied for a head of 2m to 70 m. The runner diameter is available from 0.6 m to 5 m. Power capacity is from 55 kW to 50 MW.

Pelton turbine The runner has bucket shaped blades on the periphery. The jet of water is tangential to the runner. The characteristics are, high head applications, a simple design, few problems with cavitation, highly cost effective. Pelton turbines can be supplied for a head of 100m to 500 m. The runner diameter is available from 0.55 m to 1.5 m. Power capacity is from 200 kW to 10 MW. Inclined jet turbine: The water flows into and out of the runner at an angle to the main shaft. The characteristics are high efficiency over a wide range of water flow, more flexible installation options, somewhat more complex than a Pelton turbine. Inclined jet turbines can be supplied for a head of 60m to 300 m. The runner diameter is available from 0.32 m to 0.8 m. Power capacity is from 55 kW to 6.3 MW.

In a Francis turbine, the water flows radially into the turbine and axially out of the runner. The Francis turbine, invented by an American engineer in 1849, is the most widely deployed modern turbine. The main characteristics of the Francis turbine are - a wide range of water head, simple and reliable structure, and high efficiency. A Francis Turbine can be supplied for a head of 15 m to 250 m. The runner diameter is available from 0.4 m to 4.5 m. Power capacity is from 75 kW to 50 MW. New style francis turbine, compared to the old one, it has the advantages of convenient installation, high efficiency, low noise and compact structure.

Firewood, pellets from sunflower husks, bran and straw; briquettes from corn straw etc.; e bikes; small wind turbines.

Hydropower equipment, hydro turbine, hydropower plant, kaplan turbine, francis turbine, pelton turbine, tublar turbine, turgo turbine, turbine spare parts, generator, tiller, runner blade, water pump.Site survey & design, exporting, erection and commissioning, plant management and maintenance, technical support

turbine Material:low alloy Weight:60.7kg Process: investment casting+Machining Description:Turbine is a rotary mechanical device that extracts energy from a fluid flow and converts it into useful work

Material:low alloy Weight:60.7kg Process: investment casting+Machining Description:Turbine is a rotary mechanical device that extracts energy from a fluid flow and converts it into useful work

Turbine We offer the best competitive pricing for a large range of parts from nuts and bolts, gaskets, thermocouples, valves and sensors to major "Hot Gas Path" components such as nozzles, buckets, X-Fire tubes, combustion liners, fuel liners, fuel nozzles, and transition pieces. All of our parts carry a full one-year warranty against defects in material or workmanship.

Turbines This is heavy turbine ...Very useful..

Turbine Blower

Wind Turbine

Francis turbine, kaplan turbine, pelton turbine, turgo turbine, bulb turbine, gate valve, butterfly valve, ball valve, synchro generator, excitation system, electric and control system. No

Proven reliability and high efficiency makes Kessels multi-stage steam turbines vital partners with the power and process industries. High fuel and energy conversion costs demand that steam turbine efficiency be as much a consideration as reliability. Kessels industrial multi-stage steam turbine line helps you meet a variety of energy requirements in industrial environments. These turbines operate at speeds up to 12,000 RPM, with steam inlet conditions up to 105 bar at 560oC, and exhaust conditions up to 12 bar.

The condensing turbines take high pressure steam, expand it in turbine nozzles and blades, and exhaust it to a condenser at lower than atmospheric pressure. It is principally used when power must be generated with minimum steam consumption. The condensing turbine may also have bleed points (uncontrolled extractions) to satisfy steam e. These type of turbines find application mainly for power generation where bleed steam is required for feed water heating (hp heater, lp heater and deaerator requirement) and / or where bleed steam is utilized to meet small process demands.

MEGATRO is now offering different types of wind generators with competitive price, which including two types, vertical and horizontal type. It is used of wind energy in the wind farm, Energy Company and other fields. MEGATRO wind-driven generator, is one kind of electro-mechanical device that can transformed wind energy into the mechanical energy, then again transforms them into the electrical energy. It uses the wind power, gathers them to the battery charging and saves the electrical energy. Besides, it also gather the electrical energy transformation and alternating current supply which voltage and hertz is 220V/50HZ ,110V/60HZ,230V/50HZ. It has the advantages of no need the fuel and can't produce pollution and noises. And it has high efficiency and good low-speed, the speed regulating system adjusts automatically to wind speed, the whole system is easy to install and convenient to maintain. It is generally suitable for the areas when the wind resources are rich. And it is widely used in the areas when the electricity is not sufficient or the electrical network is not normal. The main applied fields are as follows: air conditioning refrigerator, the washer, the illumination, the television, the searchlight, the communication equipments, the power tool and others. Our wind generator' main parameters and sizes are as follows: 1 Machine Pattern: The horizontal (or vertical) axis approaches against the wind 2 Leaf Blade Pattern: Propeller 3 Leaf Blade Number: 3 pieces 4 Wind Wheel Diameter: 2.0 m, 2.5m, 2.6m, 2.8m, 3.2m, 4.0m, 5.0m, 7.0m, 8.0m, 12.0m. 5 Rated Speed: 160----400 revolutions/Minute, 6 Rated Power: 150W, 200W, 300W, 600W, 1000W, 1500W, 2000W, 3000W, 5000W, 10KW, 20KW, 30KW, 50KW 7 Working Voltages: 12V, 24V, 36V, 48V, 60V, 96V, 108V, 220V, 380V, 420V 8 Matches the accumulator cell: 480V, 9 Starting Wind Speed: 3.0 meters/ Second 10 Design Wind Speed: 8~ 9 meters/ Second 11 Operating Region: 3~20 rice/ Second 12 Hand of Rotation: Clockwise (face wind wheel) 13 The Wind cans the utilization factor: 0.4 14 High Speed Ratios: 6: 1 to 8: 1 15 Velocity Modulation Way: Leaning tail + electric brake 16 Sets Up an Altitude: 6-9meters Place of Origin: Qingdao, Shandong, China. Availability size: Based on the customer's requirements. Fabrication: Based on the customer's requirements and other technical data agreed by both parties. Package: packed with wooden case Terms of Payment: L/C, T/T Minimum Order Quantity: 1sets Port of Loading: Qingdao Port Delivery Time: one month or based on the customer's needs. Export standard package or as per client

In turkey we are producing high quality wind turbines .Please ask for our catalogs for detailed information. Tower type: composite coating over steel lattice Tower weight :18t Rotor blade type: horizontal axis, 3 blades

Hydraulic turbines.

Steam turbines.