Trench Mesh Reinforcement Suppliers and Manufacturers

Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam. Specification of trench mesh reinforcement Surface treatment:galvanized or drawn wire Material: R250N, D500N, D500L, D300E, D500E The Tensile strength is 300Mpa. The trench mesh was produced by standard AS NZS 4671-2001 Width: 0.2m - 2.3m Length: 6m REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 Trench mesh reinforcement for footing slab construction and Waffle rafts beam and piers And Alls of using is accordance to AS NZS 2870-2011. 1. Footing slap The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments. The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different. 2. Waffle rafts beam and piers The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft: (a). pier to be located on the intersection of every third internal beam. (b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.

Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam. Specification of trench mesh reinforcement Surface treatment:galvanized or drawn wire Material: R250N, D500N, D500L, D300E, D500E The Tensile strength is 300Mpa. The trench mesh was produced by standard AS NZS 4671-2001 Width: 0.2m - 2.3m Length: 6m REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 And Alls of using is accordance to AS NZS 2870-2011. 1. Footing slap The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments. The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different. 2. Waffle rafts beam and piers The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft: (a). pier to be located on the intersection of every third internal beam. (b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.

Trench Mesh products in 6.0m x (200mm, 300mm, 400mm, and 500mm) sheet sizes and are a general-purpose ribbed mesh sheet used to reinforce concrete slabs with a narrow profile. *SPECIFICATIONS* Material Carbon Steel Grade 500 Mpa Length 6000mm x (200mm, 300mm, 400mm, or 500mm); width is dependent on number of wires (3,4, 5, or 6) Main Wire: 7.60@100, 10.70@100, 11.90@100 mm Cross Wire: 4.00@300, 4.75@300 mm *STANDARDS* Manufactured in accordance with AS/NZS 4671:2019 ACRS Certified NOTE - Can be manufactured in accordance with various international standards (EN, BS, ASTM and AS/NZS) *PACKAGING* Unit of Measure Sheets Pack Type Bundles FCL Quantity 25MT

Reinforcing Trench Mesh made from CRB550(550MPa) ribbed wires. The reinforcing trench mesh products all come 6.0m longs, available in 3-Bar, 4-Bar, 5-Bar and 6-Bar, as well as 8, 11 and 12mm wires. Its long, narrow sheets of concrete reinforcing mesh, has the continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry walls. Joint reinforcement has long proven to be necessary for superior performance of masonry wall construction. Used specifically for residential footing trenches, paths or other narrow spaces. Length m Width m Longitudinal Wires mm Cross Wires mm Mass Kg 6.0 0.2 7.6 @ 100 4.77 @ 300 7 6.0 0.3 7.6 @ 100 4.77 @ 300 9 6.0 0.4 7.6 @ 100 4.77 @ 300 12 6.0 0.5 7.6 @ 100 4.77 @ 300 14 6.0 0.2 10.7 @ 100 4.77 @ 300 13 6.0 0.3 10.7 @ 100 4.77 @ 300 18 6.0 0.4 10.7 @ 100 4.77 @ 300 22 6.0 0.5 10.7 @ 100 4.77 @ 300 27 6.0 0.2 11.9 @ 100 4.77 @ 300 16 6.0 0.3 11.9 @ 100 4.77 @ 300 22 6.0 0.4 11.9 @ 100 4.77 @ 300 27 6.0 0.5 11.9 @ 100 4.77 @ 300 33

Trench Mesh All trench mesh sheets are supplied in 6m lengths at varying width increasing from 200mm in 100mm increments. Trench mesh is used for both footings 2 layers of trench mesh and slab edge thickening one layer trench mesh with sheet mesh over. You should normally allow 65mm minimum to the edges and bottom of the footings using plastic bar chairs or trench mesh supports to keep the mesh in place.  Trench mesh is designated as x-L8TM, x-L11TM or x-L12TM. The x is the number of main bars.

Trench Rib Mesh All trench mesh sheets are supplied in 6m lengths at varying width increasing from 200mm in 100mm increments. Trench mesh is used for both footings 2 layers of trench mesh and slab edge thickening one layer trench mesh with sheet mesh over. You should normally allow 65mm minimum to the edges and bottom of the footings using plastic bar chairs or trench mesh supports to keep the mesh in place.  Trench mesh is designated as x-L8TM, x-L11TM or x-L12TM. The x is the number of main bars.  3-L8TM has three bars, which are 8 mm in diameter.  4-L11TM has four bars, which are 11 mm in diameter.

Trench Mesh is made specifically for use in residential footing trenches. Made from grade D500L ribbed reinforcing wire, Trench Mesh is made using a variety of longitudinal wires up to 12mm diameter. Cross wires are â?¯at 300mm centres. Sheets are made in 6m lengths, with widths varying from depending on the number of longitudinal wires. The longitudinal wires are at 100mm centres. The product code, for example L8TM3, refers to the ductility grade (L), diameter of main wires (8) and the number of main wires (3). Other sizes are available, contact us for more information.

Led bulb, tube light, panel light, decoration light, wall light, steel wires, steel plate, stainless steel plate, twisted wire rods, galvanized wires, wire mesh, site fencing, mosquito mesh, thread rods, rebar, twisted rods, t bar, nuts and bolts, hardware, pvc pipes, upvc pipes, api pipes, melamine, mdf board, plywood, film faced, shuttering, packing, core veneer, face veneer, hdf molded door skin, door filler, tubular particle boards, pvc boards, wpc boards, doors, block board, hard board, gypsum board, canopy, carpet, flooring wooden, bamboo, laminated engineering, tiles, granite tiles, granite blocks, black galaxy, wash basin, water closets, washbasins, ss sinks, faucets, furniture, pvc edge bending, crew, locks, pvc seals, silicone cartridges, shower enclosures, shower door hinges, handles, knobs, brackets, slides, nails, solar panels, flexible solar panels, solar power station, battery, inverters, rechargeable fans, lights, spring, 3ply disposable face mask, oxygen concentrator ,.Buying office, oem, components sourcing, value added services

Welded Wire Reinforcement (WWR) provides the exact size of reinforcement where needed through variable bar size and spacing, thereby reducing steel waste. Plain Square Mesh sheets are a multi-purpose mesh and complies with AS/NZS 4671 : 2001 Steel reinforcing materials. Plain Square Mesh sheets are available in 6 x 2.4 m. Associated standards: AS/NZS 4671 : 2001 Steel reinforcing materials Application: Welded Wire Reinforcement can be used for: Slab on Grade reinforcement Floor and Walls Systems Topping Slabs Architectural precast wall panels Tilt-up construction wall systems Shear walls Retaining walls Mechanically Stabilized Earth (M.S.E.) reinforcement

reinforcing mesh SL82 1. Material: Low carbon steel ribbed wire 2. Standard: AS/NZS4671:2001 3. Main hole size: 200x200mm, edge 200x100mm 4. Wire diameter: main wire 7.6mm, 4 longitude edge wire 5.37mm 5. Sheet size: 2.4m x 6m 6. Application: bridge, road, building, sidewalk,etc. 7. Package: steel belt, pallet 8. Delivery: within 15 days for one container 9. Payment: T/T, 30% deposit, 70% by the copy of B/L

Concrete reinforcing mesh, trench rib mesh, welded wire mesh, galvanized wire, back wire, gabion box, temporary fence.

RL1218 concrete reinforcement welded mesh 25*11.90@100 by 30*7.60@200 Main hole size: 200x200mm, edge 200x100mm Sheet size: 2.4m x 6m

Concrete Reinforced Mesh is widely used as bridge reinforced mesh, road construction mesh, floor reinforced mesh, trench mesh, Concrete slab mesh, Masonry mesh and brick wall reinforced mesh, which is used in construction reinforcement, the ground for the tunnels, bridges, highway and airport, wharf and wall. It is a type of convenient and economical reinforcement option for modern concrete structures. Specification of concrete reinforced mesh: (1)Material:plain steel bar, stainless steel rebar rods. (2)Steel rods style: ribbed or smooth. (3)Rebar Diameter: 3 mm - 40 mm. (4)Mesh shape: square or rectangular . (5)Distance between rods : 50,100, 150, 200,300, 400 mm. (6)Mesh sheet width: from 650 mm to 3800 mm. (7)Mesh sheet length: 850 mm, 6 m, 9 m, 12 m. Features of concrete reinforced mesh: (1)High strength. (2)Anti-crack and anti-shock. (3)Hot-dip galvanized or epoxy coating after the manufactures (4)Anti-corrosion, acid-resisting. (5)Easy to install Applications of concrete reinforced mesh: (1)Concrete reinforced mesh is used as bridge reinforced construction and building, like bridge girders, bridge spans, bridge decks. (2)Concrete reinforcing mesh used in median barriers, tunnel segments, box culverts, airport and wharf. (3)Concrete reinforcing mesh used in residential, industrial and road construction, such as concrete footpaths and industrial and commercial ground slabs, precast panel construction and residential slabs and footings. (4)Constructional uses: block slab structure reinforcing, and hollowed slabs reinforcement, building wall reinforcement and support wall reinforcement. (5)Used as coal mine supporting mesh for coal mine roadway supporting.