Tobee 150mm vertical submerged chemical pump are designed for every other tank, pit or hole-in-the-ground slurry handling situation, TP150SV pumps are available in various standard lengths to suit common sump depths, for very deep sumps or where high shaft speeds limit the length of the pump, a suction extension pipe can be fitted to the bottom inlet to extend the depth of the pump by up to 2 metres. Tobee 150mm vertical submerged chemical pump specification: Size: 150mm Capacity: 108-576m3/h Head: 8.5-40m Speed: 500-1000rpm Eff.: 52% Power: Max.110kw Handling solids: 45mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc
Tobee 100mm vertical submerged chemical pump is mainly used in a variety of sump conditions, It can also be readily applied on floating dewatering or other floating pump platforms. As a true cantilevered vertical slurry pump, TP100RV vertical spindle pump does not have submerged bearings or seals, thus, eliminating the primary failure mechanism for similarly fielded pump lines. Tobee 100mm vertical submerged chemical pump Specification: Size: 100mm Capacity: 40-289m3/h Head: 5-36m Speed: 500-1200rpm Eff.: 62% Power: Max.75kw Handling solids: 32mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc
Tobee 300mm vertical submerged chemical pump is unique cantilevered design, The sump pumps doesnâ??t need any seal and seal water. The TP300TV pumps are preferred by many customers with special installation requirements and widely applied in sump. Its wear-resistant metal liner could handle abrasive slurries with rough particles and high concentration. Tobee 300mm vertical submerged chemical pump Specification: Size: 300mm Capacity: 288-1267m3/h Head: 6-33m Speed: 350-700rpm Eff.: 50% Power: Max.200kw Handling solids: 65mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc
Tobee 65mm vertical submerged chemical pump is mainly used to transfer high- hardness, strong-corrosion and high-concentration liquids that contain suspended solid particles, The metal lined and elastomer rubber lined is interchageable for different duties, such as finished ores, refuse ores, ashes, cinders, cements, mud, mineral stones and etc. Tobee 65mm vertical submerged chemical pump Specification: Size: 65mm Capacity: 18-113m3/h Head: 5-31.5m Speed: 700-1500rpm Eff.: 60% Power: Max.30kw Handling solids: 15mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc
Tobee 250mm vertical submerged chemical pump is centrifugal sump slurry pumps submerged in sump to work.It is designed for delivering abrasive, large particle and high density slurries. The pumps have no need of any shaft seal and sealing water. it can also be operated normally for insufficient suction duties. The submerged depth can be customed as different sump. Tobee 250mm vertical submerged chemical pump specification: Size: 250mm Capacity: 261-1089m3/h Head: 7-33.5m Speed: 400-750rpm Eff.: 60% Power: Max.200kw Handling solids: 65mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc
Tobee 200mm vertical submerged chemical pump are an ultra-heavy duty design for continuous operation, the bearing assembly design allows the pumps to operate in very tough conditions without damaging the bearing. Both high chrome alloy and elastomer wet end parts are suitable to the different applications, and the pumps use in many industries, various lengths and suction extensions are available to suit most sump depths. Tobee 200mm vertical submerged chemical pump Design Features: Less wear, less corrosion Wetted components are available in a wide range of alloys and elastomers. Tobee selects the optimum combination of materials for maximum resistance to wear in virtually any industrial application, including those demanding both abrasion and corrosion resistance, and where larger particles or high density slurries are encountered. Abrasion resistant Ultrachrome T05 alloy. Abrasion/corrosion-resistant Hyperchrome T49 alloy. Corrosion-resistant stainless steels. Natural and synthetic elastomers. No submerged bearing failures The robust cantilever shaft avoids the need for lower submerged bearings which are often the source of premature bearing failure. Heavy duty roller bearings, above mounting plate. No submerged bearings. Labyrinth/flinger bearing protection. Rigid, large diameter shaft. No shaft sealing problems The vertical cantilever design requires no shaft seal. No priming required. The top and bottom inlet design is ideally suited for â??snoreâ?� conditions. Less risk of blocking The screened inlets and large impeller passages reduce the risk of blockages. Zero ancillary water costs The vertical cantilever design with no gland or submerged bearings avoids the need for expensive gland or bearing flushing water. Tobee 200mm vertical submerged chemical pump On-site Applications: Mining Sump drainage Coal prep Mineral processing Mill sumps Tunnel Tailings Chemical slurries Ash handing Paper and Pulp Waste sludge Coarse sand Lime mud Phosphoric acid Sump Dredging Mill grinding Alumina Industry Power Plant Potash Fertilizer Plant Other industries
Tobee 40mm vertical submerged chemical pump works underwater for delivering heavy concentration abrasive & corrosive slurry with big particles. pump column is made by steel or elastomer covered steel, For rubber lined pump, all wetted parts are made by elastomer for delivering strong corrosion slurry. Tobee 40mm vertical submerged chemical pump specification: Size: 40mm Capacity: 7.2-29m3/h Head: 4-28.5m Speed: 1000-2200rpm Eff.: 40% Power: Max.15kw Handling solids: 12mm Materials: High chrome alloy, Rubber, Polyurethane,Ceramic etc
Our product ranges of different verticals . chemicals pet coke, urea, coal, sulphur granules, npk, ammonium sulphate, pure aluminium, meg, deg, teg, mea, dea, tea, sulphuric acid, etc fertilizer npk, urea, ammonium sulphate specialties metal cutting additives, water treatment chemicals ro antiscalant, non oxidising biocide glutaraldehyde, textile chemicals ecofriendly products coconut fibre, coconut pith, bentonite clay (bleaching earth), etc plant design and supply engineering service and material supply, electrical and instrumentation bulk, automation , telecom, piping , engineering skids, rotary (small size) , epc for lubricant batch plants medical items :syringes (luer slip), hypodermic needles technical consultancy for setting up of laboratory r & d (state of art facility) and qc for lubricants, fuel and petrochemicals.Trading house, sourcing agents, business house, , chemicals, petrochemicals, plant design and supplies, technical consultancy
Materials: carbon steel and stainless steel (302,304,304L,316,316L etc). Characteristics:The welded stainless steel water well screen is made up of rods and warp. The rod can be round wire, triangular wire or trapezoid wire. The warp is triangular wire (V-shaped wire). Water well screens have a structure and high open area, as well as accurate slot dimension. At the same time, water well screen have heat-resisting, anti-corrosive, good machine capability, last long, safety and reliability and so on characteristics. It can be used in many kinds of medium filtering. Uses: The strainer is a kind of filtered water tubing with the perforation .it can use with the deep well pump, dive the water pump, also may use in the water-treating equipment, the environmental protection, the sea water transforms into the industrial water and life use water desalination treatment, running water treatment, water softening treatment, the petroleum industry: The petroleum product terminal filters and the chemical acid, the alkali liquid filters, the ethyl alcohol and so on the organic solution recycling filters. Continuous slots significantly increase discharge area,thus providing greater access to water-bearing zone . We can produce this pipe with diameter 80mm-550mm ,slot size 0.1mm-10mm,length 50mm-5850mm .
Tobee WNQ Submerged Dredge Pumps are also known as onboard dredge pumps, It can either be installed onboard of the dredging vessels or in the suction pipe or cutter ladder as submerged pump. Onboard dredge pumps are the primary power source for transporting the mixture to the hopper or discharge location. The dredge pumps are also essential for mixture transport in stationary dredgers and at pipeline booster stations. The WNQ series dredge pumps are single-walled conventional and high performance types, complete with drive, support and control systems. They can respond to a wide range of operational requirements. Each offers benefits according to dredging materials, circumstances, and weight and space limitations. Design Features: Heavy Duty - a double-walled pump construction fully equipped with interchangeable wear parts. Excellent configuration for the most demanding operations. Performance - a single-walled construction furnished with, where possible, replaceable wear parts. An all purpose dredge pump and balanced option as regards weight, size and replaceable wear parts. Easy - for operations that are less demanding. This is a single-walled construction without any replaceable wear parts - a pump construction with as few components as possible.
Vertical Sump Pump or Long Shaft Pump. We manufactured vertical pumps for the applications with low net positive suction head, cryogenic temperatures where vertical lift is required and in also in sump and cooling water services. Our vertical pumps is specially designed for service in water, chemicals, sewage and slurries. Vertical pumps are cover a wide range of hydraulic condition to meet virtually every pumping service in the industry and optimum efficiency.
V4 Borewell Submersible Pumpset Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP) - Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. Single Phase available in 0.5 HP to 5.0 HP Three Phase available in 1.0 HP to 6.0 HP - Speed : 2880 RPM - Head Range : 10 Mtr. To 340 Mtr. - Discharge Range : 450 LPM to 12 LPM - Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0 - Degree of Protection : IP 58 - Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph - Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs, 2.2kW, 7.5 kW -1500 lbs. - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph Direct Online (D.O.L) - Maximum Starts Per Hour : 20 Times
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m�²/sec (max.) - Ph Value : 6.5 to 8.5
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Assay 99%
Heavy duty submerged slurry pumps are vertical, shaft driven centrifugal slurry pumps designed for transferring abrasive and high density slurries from sumps, pits and other submersible source. The position of the shaft of the vertical slurry pump is perpendicular to the horizontal plane, the pump end is under the water and the motor above the liquid level. Features -The rotor parts can be adjusted axially and supported by multiple points, so heavy duty cantilever sump pump can operate steadily and reliably. -The pump adopts a long shaft structure and can be inserted up to 10 meters deep. Shaft coupling is safe and reliable. Convenient disassembly. -The impeller is immersed in the medium when the pump starts, so it is easy to start, and there is no air exhaust problem. -The outlet flange is a half movable flange for easy connection. Series SP(R) slurry pump is centrifugal vertical sump pump, work under fluid. It widely used for delivery abrasive, high density slurry with large particle in the metallurgy, mine, power plant, chemical, and other industry. Shijiazhuang Jiemu Machinery Equipment Co.,Ltd is one of the leading private indenting firms of China having 15 years of experience in Mining, Fluid Transportation and Fire Emergency Field. It works on design theory of slurry pump and water pump, experimental researches of pump performance wear mechanism and new products developing, and involves in research, design, manufacturing and sales.
65 QV-SP Vertical Slurry Sewage Pump is a cantilever sump pump,Which work submerged to transport high abrasive and high density slurries with large particles.It doesn't need any seal water. Hard metal lined or fully rubber lined fitted.High capacity double suction semi-open impeller design.and suction agitator is also available.
Plunger Type Pumps, Hydraulically Actuated Diaphragm Type Pumps, Mechanically Actuated Diaphragm Type Pumps, Solenoid, Operated Diaphragm Dosing Pumps, Complete Skid Mounted Dosing Systems, Chemical Process Pumps, Seal free Magnetic Drive Pumps, Progressive Pumps, Y Type Strainers, Pulsation dampners, etc.
Tobee SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits.
Tobee SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits. Design Features: Less wear, less corrosion Wetted components are available in a wide range of alloys and elastomers, from which Weir Minerals selects the optimum combination of materials for maximum resistance to wear in virtually any industrial application, including those demanding both abrasion and corrosion resistance and where larger particles or high density slurries are encountered.
