Designations TIANQIU: LR03 IEC: LR03 Other: AAA, AM-4 Chemical system: Zinc-Manganese Dioxide Nominal voltage: 1.5V Nominal capacity: 1200mAh Shelf life:Three years after delivery under normal storage conditions.
Product Brands: ABC, ABC Alkaline. Available Variants: AAA, AA, C, D, 9V Product of Indonesia
Model: LR03 Size: AAA Duration: 140 mins Capacitance: 650 mAh Condition: 3.9¦¸ 24 hours discharge continuously, end point 0.9V Diameter: 10.15mm Height: 44mm Weight: 11.5g. Shrink packing, blister card packing, bulk packing.
1 Summary This specification defines the SUM for high Capacity Alkaline cells LR6 1.1 Type IECLR6 OtherAAE914006 JISAM3 1.2 Reference standard IEC 60086-1 --- Primary Batteries - Part 1: General IEC 60086-2 --- Primary Batteries - Part 2: Physical and electrical specification 1.3 Execution standard GB/T 8897.2 2 Chemistry composition Zinc ,EMD , Potassium hydroxide, Graphite 0.00% Mercury & Cadmium 3. Normal voltage1.5V 4. Average weight: 23.0g 5. Nominal Capacity 2500mAh (condition: 43 load resistance, discharge 4 hours per day at 20+/-2°C, end-point voltage 0.9V ) 6 Electrical performance Test conditionLoad Resistance ( ±0.5%) 3.9©Time0.3s, Temperature20±2ã O.C.V C.C.V Accept Level V V 30 days after delivery 1.55 1.45 45 for 3 months 1.52 1.40 MIL-STD105E?¡AQL=0.4 Normal temperature for 12 Months 1.52 1.40 7 Service Life Test condition: 20±2 and 60±15%RH (Discharge Method) Minimum Average Duration ITEM Load Cutoff 30days 45 for 3 Normal Temperature Time Resistance VoltageV After delivery months for 12 Months 43© 4h/d 0.9 90h 81h 81h 3.9© 1h/d 0.8 390min 361min 361min 10© 1h/d 0.9 18.5h 17 h 17 h (IEC ITEM) 1.8© 15sec/min 0.9 600 Cycles 540 Cycles 540 Cycles 250mA 1h/d 0.8 420min 380min 380min 3.9© 24h/d 0.9 350min 315min 315min (REF ITEM)
Cashew nuts, sisal fiber, battery scraps, used rails scraps, aluminum wire scraps, almond nuts, cloves, macadamia nuts, black pepper, white pepper.Distrubuting agent and trader
Drained battery scrap (free of battery acid/fluid) including lead plates and plastic/rubber casing complete with caps. Purity : Complete Battery with full contents, except the liquid Car batteries are treated as hazardous waste. Material Origin : Car Battery / Van Battery / marine batteries and industrial traction batteries. Drained Lead Car Battery Scraps (Rains) Drained Lead-Acid Battery Scrap (RAINS per ISRI Specifications). Our Acid Battery Scrap on 99.99%. . Automotive Waste Batteries completely washed, cleaned with lead acid contents. RAINs per ISRI Specifications) (Product Detailed SpecWET/DRY WHOLE INTACT CAR LEAD BATTERIES(RINKs and ifications) height :116mm and whight :310 gr height :123mm and whight :350 gr Used Auto Battery Scrap Drained lead battery scraps Lead Battery Plate Scrap Type Battery Scrap 20D 16H Lead Battery Plates Scrap Lead Battery Plate Scrap Type soft lead scrap Drained / Dry Whole Intact Lead Batteries (RAINS) Lead Battery Scrap >> Drained / Dry Whole Intact Lead Batteries (RAINS) SCRAP DRAINED/DRY WHOLE INTACT LEAD BATTERIES : To be free of any liquid. Cases to be either plastic or rubber and be complete including caps. Non-lead (ni-cad, ni-fe, carbonaire, etc.) not acceptable. Seller Listings Drained / Dry Whole Intact Lead Batteries (RAINS) 6V1.3AH sealed lead acid battery. 1/Product Specification: Item No.:DHB613; Voltage:6V; Normal capacity:1.3AH/20hr; Dimension(L*W*H):97*24*52mm; Total height(with terminal):57mm; Weight:0.30kg; 2/Product Feature: (1)Maintenance-free operation.there is no need to check specific gravity of the electrolyte or add water to battery during float service life. (2)Low self-discharge rate, small internal resistance. (3)The unique construction and sealing techniques of the battery, add the ABS plastic crust that guarantee leakproof operation in and position with no adverse effect to capacity or service life. (4)With our high quality lead-tin-calcium alloy grids, it has a long usage life and deep discharge recoverability. (5)No pollution and no harm.
Our Acid Battery Scrap on 99.99%. Monthly Supply Capacity: 500 - 1500 metric tons, Type: all kind of scrap batteries, Fe Content: HMS Fe Content (%): 100%) Drained Battery Scrap: Black Packaging Detail: Pallet with shrink wrapping Battery features: - Sealed and maintenance free operation battery - Non-Spillable construction design. - ABS Containers and Covers (UL94HB), UL94V-0 optional. - Safety valve installation for explosion proof. - High quality and high reliability. - Exceptional deep discharge recovery performance. - Low self discharge characteristic. - Flexibility design for multiple install positions. - No memory effec - CE certificate - Wide operating temperature range Battery Application: -Solar system - Alarm System - Cable Television - Communication Equipment - Control Equipment - Security System - Medical Equipment - UPS - Power Tools - Toys - Emergency Power System - LED Lig WE ARE TRADING MANUFACTURERS OF ALL TYPES OF used car scrap battery WORLDWIDE. Specifications we are offer 1.dry charged battery & MF battery 2.Meet all DIN & JIS standard 3.Powerful quick scrap used a car battery Specifications Specifications 1.dry charged battery & MF battery 2.Meet all DIN & JIS standard 3.Powerful quick start & long life 4.1-2 year used car scrap battery 2/Product Feature: (1)Maintenance-free operation.there is no need to check specific the gravity of the electrolyte or add water to a battery during float service life. (2)Low self-discharge rate, small internal resistance. (3)The unique construction and sealing techniques of the battery, add the ABS plastic crust that guarantees leakproof operation in and position with no adverse effect on capacity or service life. (4)With our high-quality lead-tin-calcium alloy grids, it has a long usage life and deep discharge recoverability. (5)No pollution and no harm. Drained Lead Car Battery Scraps (Rains) Drained Lead-Acid Battery Scrap (RAINS per ISRI
The primary use of Ammonium Sulphate is as a fertilizer for alkaline soils. In the soil the ammonium ion is released and forms a small amount of acid, lowering the pH balance of the soil, while contributing essential nitrogen for plant growth. The main disadvantage to the use of Ammonium Sulphate is its low nitrogen content relative to Ammonium Nitrate, which elevates transportation costs. It is also used as an agricultural spray adjuvant for water soluble insecticides, herbicides, and fungicides. There it functions to bind iron and calcium cations that are present in both well water and plant cells. It is particularly effective as an adjuvant for 2,4-D (amine), glyphosate and glufosinate herbicides.
Commodity : Soda Ash Light / Dense Molecular formula:na2co3 Molecule weight:105.99 H.S Code:28362000 Cas: 497-19-8 Properties : white crystal powder, easily soluble in water, water solution is alkali. Easily absorbing moisture and co2 if exposing in the air. Applications: mainly used in glass-manufacturing, chemical industry, metallurgy, paper, dye, synthetic washes and petrochemistry. Packing :25kg/ 40kg/50kg/750kg pp woven bag with waterproof pe inner , two layers Specifications standard : gb210.1-2004 Items : specification First grade : specification Second grade Total alkalinity(as na2co3 in dry base) %99.2% min98.8% min Chloride content(as nacl) %0.7% max0.9% max Iron content(as fe in dry base) /%0.003% max0.0035% max Sulphate content(as so4 in dry base) /%0.03% max0.03% max Water insoluble matter /%0.03% max0.03% max Loss on ignition a/ %0.5% max0.5% max
Mobile Phones Scrap, Cell Phone Scrap, Cell Phone Battery Scrap
Product Name Sodium Benzoate Specification Food Grade Appearance White Powder/Granular/Sphere Certification FDA, GMP, HACCP, ISO, KOSHER, QS, Halal Purity: 99.5% min [Molecular formula] C7H5NaO2 [Molecular weight] 144.11 [Use] widely used in food industry as Antiseptic, anti-animalcule and antifreezing agent used in food, medicine, tobacco, plating, printing and dyeing [Quality index] in accordance with GB1902-2005 standard for edible grade and BP98 and China national codex 2000 for medicinal grade Package: 25kg net packed in woven bag, or 600kg net packed in ton bag Container: 17MTS/20'FCL without pallets, 14MTS/20'FCL with pallets For extruded, 16MTS/20' container For powder: 17MTS/20' container For granule: 20MTS/20' container Item GB1902-94 version BP98 version China pharmacopoeia 2000 version Content(base on C7H5NaO2 dry basis),% 99.0 99.0-100.5 99.0 Drying loss,% 1.5 2.0 1.5 Dissolve Meet the stipulation Meet the stipulatio Transparency and color / Meet the stipulation Alkalinity acidity; Meet the stipulation Meet the stipulation Meet the stipulation Cchloride (base on Cl) 500PPm 200PPm/ Chloride(base on Cl),/ 300PPm/ Heavy metal(base on Pb) 10PPm 10PPm 10PPm As(base on As),2PPm/ 5PPm Sulfate (base on SO4),1000PPm // Readily oxidizable substance Passed the test/ o-benzene tricarbonic acid Passed the test/
Certification CE,UL,REACH,ROHS,MSDS Discharge Time >130min Norminal Voltage 1.5V Weight 11-12g Package Shrink package/Blister package/Customized Application Watches,Electric calculator,toys,Teaching machine,Currency detector,Electronic dictionary and so on
Type:LR1130H Norminal voltage:1.5V Norminal capacity:60mAh End point voltage:0.9V Dimension:3.05*11.6 mAh Weight:1.14g
Magnesia Bricks Description Magnesia Bricks are alkaline refractory materials. These products have over 90% magnesium oxide content and adopt periclase as the principal crystalline phase. Magnesia Bricks can be divided into two categories of Burnt Magnesia Bricks and Chemical Bonded Magnesite Brick. They have excellent performance of superior high temperature mechanical strength and volume stability. Magnesia Bricks can service in the high temperature of 1750.. They are ideal products for glass furnace application. Magnesia Bricks Features: It is a kind of alkaline refractory product with periclase as main phase magnesite-alumina spinel clinker as basic material. the product has such characteristics as good temperature vibration, good strength and volume stability in high temperature. Magnesia Bricks Application Basic open-hearth furnace for steelmaking Electric furnace bottom and wall Permanent lining of oxygen converter Non-ferrous metal metallurgy furnace Hyperthermia tunnel kiln Lining of rotary cement kiln Heating furnace bottom and wall Regenerative chamber of glass furnace Magnesia Bricks Properties High Refractoriness Good alkaline slag erosion resistance High apparent initial softening temperature Good thermal conductivity High thermal expansion Magnesia Bricks Manufacturing Process Burnt Magnesia Bricks are manufactured with magnesite clinker as the raw material and fired in the high temperature of 1550~1600 after smashing, burdening, mulling and molding. High-purity products can be fired in the temperature that over 1750. Chemical bonded magnesite brick is produced with certain chemical bonding through mixing, molding and drying.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Product name - A/AA/AAA grade pumpkin seed kernels GWS Broken - 3% Max Cultivation Type - Common Processing Type - Raw Style - Dried Ceitifications - ISO 9001,ISO 22000 Grade - high grade Usage - human consumption Crop - 2020 Color - dark green Moisture - 8 % Max MOQ - 1 Ton Storage - Dry Clean Place Avoid Sunlight Amixture - 0.3% Max Packing - 25kg plastic woven bag or according to your demands Purity -99.7%
Copper cathode, copper wire scrap, sunflower oil, soybeans seeds, used rails, palm oil, urea 46% nitrogen granular, white corn, sisal fiber, cashew nut, sesame seed, hardwood charcoal, a4 paper icumsa 45 sugar, wood pellets, paper scrap, used engines, yamaha cardboard engines, pet bittle scrap, almond nuts, pistachio nuts, battery scrap, computer scrap, phone scrap, beef meat, goat meat, lamb meat, wet salted cow, cocoa, arabica coffee.
Product Features: 1 All-in-one design, high integration and space saving installation 2 Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years 3 Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability 4 Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage 5 BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range 6 CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability 7 System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell 8 Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; 9 Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics 1 Small size and light weight, Maintenance-free 2 Environmental protection and pollution-free materials, no heavy 3 Accurately estimate the state of charge of the battery pack, that is, the remaining power of the battery, to ensure that the power of the battery pack is maintained within a reasonable range 4 Built-in BMS management system with comprehensive protection and monitoring control functions 5 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells 6 Main control MCU can be centrally controlled and manage peripheral settings (AC charging module, inverter module, solar charging module) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable
1 All-in-one design, high integration and space saving installation 2 Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years 3 Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability 4 Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage 5 BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range 6 CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability 7 System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell 8 Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; 9 Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics 10 Accurately estimate the state of charge of the battery pack, that is, the remaining power of the battery, to ensure that the power of the battery pack is maintained within a reasonable range 11 Built-in BMS management system with comprehensive protection and monitoring control functions 12 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells 13 Main control MCU can be centrally controlled and manage peripheral settings (AC charger, inverter, solar charger) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable
ESS 215KW Lithium Battery Energy Storage System 384VDC Rechargeable Lifepo4 Battery pack 280AH Energy Storage Battery 1. High energy density, small footprint, short construction period, strong environmental adaptability 2. Standardized components, modular architecture, easy for expansion 3. Battery module within the layered stack design, with more than 10 years of long design life 4. Efficient battery module and system cooling design 5. The use of international advanced IGBT and intelligent power module, with high power fast adjustment capability 6. BMS battery management system with SOC automatic calibration and high current active balance function, combined with the perfect operation control and management strategies to achieve accurate and efficient management 7. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system 8. Our BMS use NXP(USA) automotive-grade high performance chip, strong anti-interference, good reliability, wide temperature range. 9. We use brand new high quality A-grade battery power cell, longer service life. 10. Charging and discharging are controlled separately, more convenient and reliable to control charging and discharging. 11. Big color LCD touch screen display, easy setting and operation. 12. Can built in solar charge controller and AC-DC charger, our BMS can intelligently manage charger to charge battery well, BMS can communicate well with battery, solar controller, ac charger and inverter, one integrated intelligent monitoring system. 13. Approved by UL1741 certificate. 14. Accept customized product, our lithium battery system are widely used in many situations, such as: Different residential home, hotel, shop, factory, hospital, commercial buildings, electric car, RVs, Van, mobile dining car, heavy truck, different ship/boats, ice-cream car, outdoor camper,.etc. Applications: 1.Energy Storage --Solar-Wind Power System / City Grid (On/Off) / Community and Family 2.Back-up System and UPS --Telcom Base / CATV system / Computer Server Center / Medical Instrumnt / Military Equipment 3.Other Applications --Security and Electronics / Mobile POS, Mining Lihgt / Torch / LED Light / Emergency Light --RV Motorhome /Golf Carts Battery / Boat Marine Yachts / Electric Skateboard / Electric bike / Electric Scooter / Electric bicycle --LED Backup / Engine Starting Battery,etc.
