Resin Internal Grinding Wheel For Hvof Coating Suppliers and Manufacturers

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

Ginger (Zingiber Officinale) is a commodity that is highly valued in international markets for its aroma, pungency and high oil and Aleo resin content. Nigeria is the third largest exporter of ginger in the world after China and India. Most of the dried ginger that are available for international trade are simply sun dried over a few days, but artificial drying is also used in areas lacking a defined dry season to coincide with the harvest. The rhizome is dried to 10-12 percent moisture content. Dried ginger is usually presented in a split or sliced form. Splitting is said to be preferred to slicing, as slicing loses more flavor, but the sliced are easier to grind and this is the predominant form of dried ginger currently in the market

Mace Botanical: Myristica fragrans Family: N.O. Myristicaceae Hindi Name: Mace - Javitri General Description: Nutmeg, spice consisting of the seed of the Myristica fragrans, a tropical, dioecious evergreen tree native to the Moluccas or Spice Islands of Indonesia. Geographical Sources The nutmeg tree, Myristica fragrans, is indigenous to the Moluccas in Indonesia but has been successfully grown in other Asian countries and in the Caribbean, namely Grenada. Banda Islands, Malayan Archipelago, Molucca Islands, and cultivated in Sumatra, French Guiana Composition -> Nutmeg and mace contain 7 to 14 percent essential oil, the principal components of which are pinene, camphene, and dipentene. Nutmeg on expression yields about 24 to 30 percent fixed oil called nutmeg butter, or oil of mace. Dried kernel of the seed. Varieties -> Whole nutmegs are grouped under three broad quality classifications: 1. Sound: nutmegs which are mainly used for grinding and to a lesser extent for oleoresin extraction. High quality or sound whole nutmegs are traded in grades which refer to their size in numbers of nutmegs per pound: 80s, 110s and 130s (110 to 287 nuts per kg), or 'ABCD' which is an assortment of various sizes. 2. Substandard: nutmegs which are used for grinding, oleoresin extraction and essential oil distillation. Substandard nutmegs are traded as 'sound, shrivelled' which in general have a higher volatile oil content than mature sound nutmegs and are used for grinding, oleoresin extraction and oil distillation; and 'BWP' (broken, wormy and punky) which are mainly used for grinding as volatile oil content generally does not exceed 8%. 3. Distilling: poor quality nutmegs used for essential oil distillation.Distilling grades of nutmegs are of poorer quality: 'BIA' or 'ETEZ' with a volatile oil content of 8% to 10%; and 'BSL' or 'AZWI' which has less shell material and a volatile oil content of 12% to 13%. Method of Processing -> When fully mature it splits in two, exposing a crimson-coloured aril, the mace, surrounding a single shiny, brown seed, the nutmeg. The pulp of the fruit may be eaten locally. After collection, the aril-enveloped nutmegs are conveyed to curing areas where the mace is removed, flattened out, and dried. The nutmegs are dried gradually in the sun and turned twice daily over a period of six to eight weeks. During this time the nutmeg shrinks away from its hard seed coat until the kernels rattle in their shells when shaken. The shell is then broken with a wooden truncheon and the nutmegs are picked out. Dried nutmegs are grayish-brown ovals with furrowed surfaces. Large ones may be about 1.2 inches long and 0.8 inch in diameter. Taste and Aroma: Nutmeg has a characteristic, pleasant fragrance and slightly warm taste

Paprika is a spice made from the grinding of dried fruits of Capsicum annuum (e.g., bell peppers or chili peppers). In many European languages, the word paprika refers to bell peppers themselves. The seasoning is used in many cuisines to add color and flavor to dishes. Paprika can range from sweet (mild, not hot) to spicy (hot). Flavors also vary from country to country. Usage Paprika is used as an ingredient in a broad variety of dishes throughout the world. Paprika is principally used to season and color rices, stews, and soups, such as goulash, and in the preparation of sausages as an ingredient that is mixed with meats and other spices. Paprika can also be used with henna to bring a reddish tint to hair when coloring it. Paprika powder can be added to henna powder when prepared at home. Paprika is also high in other antioxidants, containing about 10% of the level found in berries. Prevalence of nutrients, however, must be balanced against quantities ingested, which are generally negligible for spices. Paprika oleoresin (also known as paprika extract) is an oil soluble extract from the fruits of Capsicum Annum Linn or Capsicum Frutescens(Indian red chillies), and is primarily used as a colouring and/or flavouring in food products. ... Oleoresin Paprika is produced by the extraction of lipids and pigments from the pods of sweet red pepper, Capsicum Annuum L. Grown in temperate climates. An oil soluble extract with it is widely used in processed foods such as sausage, dressings, dry soluble seasonings, food coatings, and snack food seasonings. Paprika Oleoresin, obtained from Capsicum, is a natural dye used as a colorant and a flavor enhancer in foods, meats and pharmaceuticals. It is obtained by percolation with a volatile solvent which should be removed subsequently, such as acetone, trichloroethylene, 2-propanol, methanol, ethanol and hexane. Capsaicin is the major flavouring compound, whereas capsanthin and capsorubin are major colouring compounds among variety of coloured compounds present in Paprika Oleoresin. Uses Foods coloured with paprika oleoresin include cheese, orange juice, spice mixtures, sauces, sweets and emulsified processed meats. In poultry feed it is used to deepen the colour of egg yolks.

Commodity: Synthetic Cryolite Formula: Na3AlF6 M.W.: 209.95 Properties: The product is a white crystalline powder or a sandy-size granularity, and a pinkish crystalline powder or a sandy-size granularity as well. Sp.gr.2.953.01g/cm3, melting point about 1000centigrade, specific heat 1.056j/gcentigradeat 18100centigrade. Its slightly soluble in water, but insoluble in anhydrous hydrogen fluoride. The content of its crystal water will be decreased while the increasing of the molecular ratio, therefore its loss on ignition will be also decreased while the increasing of the molecular ratio. After the paste of synthetic cryolite with different molecular ratio dehydrates, the loss on ignition at 800centigrade will appear 10.34%, 6.22% and 2.56% when the molecular ratio reaches 1.74, 2.14 and 2.63 reactively. Specifications: Appearance white powder F 52% min Al 12% min Na 33% max SiO2 0.36% max Fe2O3 0.08% max CaO 0.5% max P2O5 0.03% max SO4 0.6% max H2O 0.4% max Loss on ignition 2 % max Uses: Its mainly used as a flux in the aluminum smelting by fused-salt electrolysis; also an opalizer in the manufacture of enamel; an opacifier and auxiliary solvent of glass and enamel; an insecticide of crops; a flux in aluminum alloy casting; and in the production of ferrous alloy and effervescing steel; as well as a wear-resistant filler for resin and rubber-boned abrasive wheels. Packing & Storage: In plastic coating woven bags with plastic film inside, 25kg,40kgs, 50kgs or 1000kgs net each, or as the requirement of clients.Stored: in a cool , ventilated, dry place.

Product Name: Disposable Vinyl/Nitrile Blend Examination Gloves One-time use, no sterilization, no latex Single use, non-sterile, Latex free Model: S, M, L, XL Sizes: S, M, L, XL Color: blue, green, black, etc. Color: Blue, Green, Black etc. Structure: 5 fingers, with curling, regardless of left and right hands Structure: 5 fingers, beaded cuff for easy donning, ambidextrous Surface type: smooth surface Surface: Smooth Features : PVC/nitrile synthetic gloves are made of PVC resin and nitrile latex material. The product has PVC and The double advantage of nitrile gloves. The Vinyl/Nitrile Blend gloves is compounded with PVC paste and Nitrile latex, and the finished product has the advantage of both PVC and Nitrile glove. The donning feeling is better than vinyl gloves. Much softer than vinyl gloves Sturdy, wearable, longer wearing time than nitrile gloves The wearing time is longer than nitrile gloves. Has good wet hand wearability, easier to wear than nitrile and PVC gloves Easy donning with wet hands and easy donning than nitrile &vinyl gloves. PU coating, free of protein, effectively reduces the risk of allergies PU coating, with no protein in it, allergy risk is reduced effectively. Has better protection, has better acid resistance, alkali resistance and oil resistance Better protection, good resistance of acid, alkali and oil. Better cost-performance

Liquid Ethyl Acetate: Ethyl Acetate is an ester of Ethanol and Acetic Acid, (systematically Ethyl Ethanoate, commonly abbreviated EtoAc or EA) an organic compound having formula CH3COOCH2CH3. Liquid Ethyl Acetate is a colorless solvent has a characteristic sweet / fruity smell. We are a distinguished Liquid Ethyl Acetate Exporter based in India. Liquid Ethyl Acetate, offered by us, is perfect in formulation is well-tested. Further, we welcome bulk orders for Liquid Ethyl Acetate with complete sense of responsibility. Applications: - Ethyl Acetate is used in a variety of coating formulations such as epoxies, urethanes, cellulosic, acrylics and vinyl’s. - Applications for these coatings are numerous wood furniture and fixtures, agricultural, construction and mining equipment, auto refinishing, and maintenance and marine uses. - Ethyl Acetate has applications as a solvent in inks for flexographic and rotogravure printing. - It is used as an extraction solvent in the production of pharmaceuticals and food, and as a carrier solvent for herbicides. - High purity product can be used as a viscosity reducer for resins used in photoresist formulations in the electronics industry.

Product name: Internal and external cylindrical grinding machine Detailed product parameter description: Product model: Shanghai Machine Tool Factory Internal and External Cylindrical Grinding Machine M1432A Grinding diameter range 8-320mm Maximum grinding length 1000/1500/2000/3000mm Maximum workpiece weight 150kg Center height 180mm Maximum movement of worktable 1100/1600/2080/3100 Hydraulic moving speed of workbench 0.1~4 m/min Workbench rotation range -3 ~+7 /-3 ~+6 /-2 Maximum linear speed of grinding wheel 35m/s Grinding wheel specifications   600- 75 305mm 50 0 (50-70) -  203mm Headstock spindle speed 25,50,75,110,150,220 r/min Taper of spindle hole of movable headstock Morse signal 4 Fixed headstock spindle taper Morse signal 5 Total motor capacity 13kw Machine tool dimensions 490 0*1810*1515/5800*1810*1515 8000*1810*1515/11050*1870*1515 Machine weight 3700/4500/6000/7500kg

Kaolin: Kaolin uses are multiple and diverse. Kaolin are used as functional filler, extender, ceramic raw material and pigment because of its whiteness and fine particle size. Kaolin also hold importance as raw material in refractory applications, concrete, rubber and fiber glass manufacturing. We, as a Kaolin Exporter welcome any size of international orders from Middle East and other countries. Applications: Paper: Kaolin used as a coating pigment and as a filler to replace fiber. It possesses desirable optical properties. Concrete: Kaolin helps to improve strength and durability of concrete. When added to concrete mix, reacts with free lime released during cement hydration to produce additional cementitious material, resulting in an improved high performance concrete. Plastics : Kaolin is widely used as filler in the plastics industry because of its inert chemical nature and its unique size, shape and structure. Agriculture : It is used as a carrier and diluent in fertilizers, pesticides and related products. It is suitable as carrier because it aides the retention of the formulations on the plant. Rubber : It is commonly used as functional filler in rubber applications. While Kaolin improves overall performance for Rubber in general, different types of white pigment play specific roles in rubber application. Paint : Kaolin used as an extender in paints. It reduces the amount of expensive pigment such as Titanium Dioxide. It assists with desirable rheological properties that help maintain proper dispersion and provide bulk to the product. Ceramic : Kaolin improves whiteness and brightness of ceramic body. Good plasticity, good shrinkage, low water absorption and casting rate are also very important properties of kaolin.

Hand-made Bamboo Lamp, Southeast Asian Style, handicraft light 100% Bamboo, Eco-friendly, colored or natural, Coated with gloss paint, fumigated Use: Restaurants, Hotels, Wholesale Size: Customizable, as per catalogue Color: Natural Packing and Shipping: International Standard Delivery time: 15 - 30 days